TP-Link Auranet User manual

REV1.1.0
191001
2075
User Guide
Wireless Ceiling Mount Access Point

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark
of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without
permission from TP-Link Technologies Co., Ltd. Copyright © 2017 TP-Link Technologies
Co., Ltd.. All rights reserved.

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1）This device may not cause harmful interference.
2）This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to
only Mobile Configurations. The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning
(CAP300)
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
(CAP1200/CAP1750)
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
RF Exposure Information
This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of
exposure of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device used at 20 cm from your
body.
National Restrictions (CAP1200/CAP1750)
Restricted to indoor use.
Canadian Compliance Statement
This device complies with Innovation, Science and Economic Development Canada
license-exempt RSSs. Operation is subject to the following two conditions:
1）This device may not cause interference, and
2）This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1）l’appareil ne doit pas produire de brouillage;
2）l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si
le brouillage est susceptible d’en compromettre le fonctionnement.
Caution (CAP1200/CAP1750)
1）The device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems;

2）For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies
with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation
as appropriate; and
The high-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference
and/or damage to LE-LAN devices.
Avertissement (CAP1200/CAP1750)
1）Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable
aux systèmes de satellites mobiles utilisant les mêmes canaux;
2）Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s)
utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée
pour l’exploitation point à point et non point à point, selon le cas.
En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour
les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement
This equipment complies with ISEDC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements ISEDC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Innovation, Science and Economic Development Canada
Statement
CAN ICES-3 (B)/NMB-3(B)

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність
вимогам нормативних документів та вимогам, що передбачені чинними
законодавчими актами України.
Safety Information
When product has power button, the power button is one of the way to shut off the
product; When there is no power button, the only way to completely shut off power
is to disconnect the product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric
shock and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
Adapter shall be installed near the equipment and shall be easily accessible.
The plug considered as disconnect device of adapter.
Use only power supplies which are provided by manufacturer and in the original
packing of this product. If you have any questions, please don't hesitate to contact us.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電
信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
(CAP1200/CAP1750)
For EU/EFTA, this product can be used in the following countries:
Explanation of the symbols on the product label
Symbol
Explanation
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or dismantled
to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or
to the retailer when he buys a new electrical or electronic equipment.
AT
BE
BG
CH
CY
CZ
DE
DK
EE
ES
FI
FR
GB
GR
HR
HU
IE
IS
IT
LI
LT
LU
LV
MT
NL
NO
PL
PT
RO
SE
SI
SK

CONTENTS
About this User Guide.............................................................................................................................. 1
Introduction ...................................................................................................................... 2
Working Mode.................................................................................................................. 3
FIT Mode................................................................................................................................. 3
FAT Mode............................................................................................................................... 4
Status.................................................................................................................................. 7
Device Information ............................................................................................................. 7
Wireless Parameter............................................................................................................ 8
Wireless Service.................................................................................................................. 8
Wireless Client ..................................................................................................................... 9
Wireless............................................................................................................................10
Wireless................................................................................................................................11
WDS Settings .....................................................................................................................14
Advanced Settings ...........................................................................................................16
Band Steering.....................................................................................................................18
Network ............................................................................................................................20
Wireless MAC Filtering ....................................................................................................20
VLAN Settings....................................................................................................................21
System..............................................................................................................................23
AP Management ................................................................................................................24
Account ................................................................................................................................25
System Log .........................................................................................................................25
Time Setting........................................................................................................................26
Configuration Management...........................................................................................27
Firmware Upgrade ............................................................................................................27
Ping Watch Dog .................................................................................................................28

About this User Guide
When using this guide, please notice that features of the CAP may vary slightly
depending on the model and software version you have, and on your location, language,
and Internet service provider. All screenshots, images, parameters and descriptions
documented in this guide are used for demonstration only.
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied. Users must take full responsibility for their
application of any product.
Convention
Some models featured in this guide may be unavailable in your country or region.
For local sales information, visit http://www.tp-link.com.
Unless otherwise noted, the CAP or the device mentioned in this guide stands for
CAP300, CAP1200 and CAP1750. Due to the similarity of their software features, we
take CAP1200 for an example to illustrate Chapter 4 to Chapter 7.
More Info
The latest software can be found at Download Center at www.tp-link.com/support.
The Quick Installation Guide can be found where you find this guide or inside the package
of the CAP.
Specifications can be found on the product page at http://www.tp-link.com.
A Technical Support Forum is provided for you to discuss our products at
http://forum.tp-link.com.
Our Technical Support contact information can be found at the Contact Technical
Support page at www.tp-link.com/support.
1

Introduction
Auranet series products provide wireless coverage solutions for small-medium
business. They can either work independently in FAT mode or be centrally managed by
the wireless controller in FIT mode, providing a flexible, richly-functional but easily-
configured enterprise-grade wireless network for small and medium business.
“Celling lamp” appearance and easily mounting design with chassis make CAP easy to
be installed on a wall or ceiling and blend in with most interior decorations.
CAP:
Figure 1-1 Top View of the CAP
2

Working Mode
CAPs support two working modes including FIT mode and FAT mode. In FIT mode, APs
can be centrally managed by TP-Link’s wireless controller. The default FIT mode is used
when you want to deploy a large wireless network. The management of every single AP
in the network is complex and complicated. With the wireless controller, you can
centrally manage the mass APs simply in a web browser.
In FAT mode, you can log in to AP’s webpage to manage the AP alone. The FAT mode is
used in a small wireless network. The AP cannot be managed by wireless controller in
FAT mode.
FIT Mode
In the default FIT mode, CAP should be managed by the wireless controller. Please refer
to the Wireless Controller User Guide from our website at www.tp-link.com to learn
more information about configuring and using the CAPs by the controller.
3

Typical topology in FIT mode:
Figure 2-1 Typical Topology in FIT Mode
NOTE:
The IP address of the wireless
controller must be reachable for the CAPs in the
network.
FAT Mode
In FAT mode, you can log in to AP’s webpage to manage the AP alone. The FAT mode is
used in a small wireless network.
CAP
Wireless Controller
Manangement Host
Clients
CAP CAP
Switch
Router
Internet
4

Typical topology in FAT mode:
Figure 2-2 Typical Topology in FIT Mode
Follow the steps below to log in to the web interface.
1. Launch a web browser, enter 192.168.0.254 in the address field and press the Enter
key.
NOTE:
To log in to the device, the IP address of your PC should be set within the same
subnet addresses of the device. The IP address is 192.168.0.x (”x” is any number
from 1 to 253). Subnet Mask is 255.255.255.0.
2. Create a new username and password for login, and then click OK.
CAP
Router
Internet
Clients
5

Figure 2-3 Login
3. The webpage will be shown as below. Click the menu bar to configure the
corresponding parameters.
Figure 2-4 Status
TIPS:
Proceed to the following chapters for information on configuring the CAP in FAT mode.
CAP1200 is taken as an example.
6

Status
The
Status
page displays the device information, wireless parameter, wireless service
and wireless client of the CAP.
Figure 3-1 Status Page
Device Information
This section displays the information of hardware version, MAC address, IP address,
system time and running time of the CAP. If you want to modify the IP address of the CAP,
Please refer to AP Management. To modify the system time, please refer to Time
Setting.
Figure 3-2 Device Information
7

Wireless Parameter
This section displays the wireless mode, channel bandwidth, channel frequency and
WDS status of the device. Please refer to Advanced Settings to configure the wireless
mode, channel bandwidth and channel frequency and refer to WDS Settings to
configure the WDS feature.
Figure 3-3 Wireless Parameter
Wireless Service
In this section, you can check or edit the wireless service information of the CAP.
Figure 3-4 Wireless Service
Click the button to edit the corresponding wireless service entry. You can change the
SSID, Network type and password. Check or uncheck the status box to enable or disable
the wireless service as needed.
Figure 3-5 Wireless
8

NOTE:
If the wireless network is not encrypted, changing password here will encrypt the network
with WPA-PSK/WPA2-PSK. If the wireless network has been already encrypted, changing
password here will not change the encryption type.
Wireless Client
The wireless client table displays the information of the connected clients including their
MAC address, connected SSID and the connection time.
Figure 3-6 Wireless Client
9

Wireless
Wireless
page consists of Wireless, WDS Settings, Advanced Settings and Band
Steering.
Figure 4-1 Wireless Page
If you have made any change of the parameters, please click OK to make the
configuration take effect. There will be a blue bar at the top of the page to remind you to
10

save the configuration. Click Save when you finish all settings, otherwise all the settings
will be recovered to last saved settings at reboot or power off.
NOTE:
Proceed to the following chapter for information on configuring the wireless network of
the CAP. The configuring information of 2.4GHz is taken as the example.
Wireless
This section allows you to configure the wireless basic settings, such as SSID, network
type, security mode, and password of each wireless service entry.
Figure 4-2 Wireless
Click Add to create a new wireless service. Click button to edit the corresponding
wireless service.
SSID: Enter a character string no more than 32 characters to name your
wireless network. We suggest you to set an easy-to-remember SSID
to conveniently identify your wireless network.
Check the box of Enable Broadcast to allow this device to broadcast
its SSID. Therefore, the hosts within its wireless coverage could find
the wireless signals.
Network Type: Select the network type of the wireless network.
11

Guest Network: The hosts in a guest network cannot communicate
with hosts in other wireless networks.
Office Network: Functions as a normal wireless network.
Security Mode: Select the security mode of wireless network. If all the hosts are
allowed to access the wireless network without password, please
select None. For the safety of wireless network, you are suggested to
encrypt your wireless network. This device provides two security
modes: WPA/WPA2 (Wi-Fi Protected Access) and WPA-PSK/WPA2-
PSK (WPA Pre-Shared Key). WPA-PSK/WPA2-PSK is recommended.
Settings vary in different security modes as the details is in the
following introduction.
AP Isolation: Select this checkbox to enable the AP Isolation feature that allows
you to confine and restrict all wireless devices on your network from
interacting with each other, but still able to access the Internet. This
function will be disabled if WDS is enabled.
Enable Wireless
Network:
Check the box to enable this wireless network, allowing the hosts
connected to the wireless network to communicate with each other.
Security Mode
Following is the detailed introduction of security mode: WPA/WPA2 and WPA-PSK/WPA2-
PSK.
WPA-PSK/WPA2-PSK
Based on pre-shared key. It is characterized by higher safety and simple settings, which
suits for common households and small business. WPA-PSK has two versions: WPA-
PSK and WPA2-PSK.
Figure 4-3 Security Mode WPA-PSK/WPA2-PSK
Authentication
Type:
Auto: Select WPA or WPA2 automatically based on the wireless
station's capability and request.
WPA-PSK: Pre-shared key of WPA.
WPA2-PSK: Pre-shared key of WPA2.
12