TP-Link Auranet EAP330 User manual

7106506302 REV1.0.0
Specifications are subject to change without notice. TP-LINK is a registered
trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product
names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any
means or used to make any derivative such as translation, transformation,
or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
www.tp-link.com
›English
› Български
› Čeština
› Қазақша
› Lietuvių
› Magyar
›Polski
› Русский язык
› Română
› Slovenčina
› Srpski jezik
› Українська мова
Ceiling Mount Access Point
Installation Guide

CONTENTS
English..................................................................................................1
Български ............................................................................................7
Čeština ...............................................................................................13
Қазақша .............................................................................................19
Lietuvių ...............................................................................................25
Magyar................................................................................................31
Polski..................................................................................................37
Русский язык .....................................................................................43
Română..............................................................................................49
Slovenčina..........................................................................................55
Srpski jezik .........................................................................................61
Українська мова ................................................................................67

1
English
Note: The image may differ from the actual product.
Network Topology
A typical network topology for the EAP is shown below.
EAP Controller
A DHCP server (typically a router) is required to assign IP addresses to the EAPs
and clients in your local network. A computer running the EAP Controller software,
which can be in the same or different subnet with the EAPs, is used to centrally
manage the EAPs.
You can get the EAP Controller software from our website http://www.tp-link.com.
Hardware Installation
■Option1：
Ceiling Rail Mounting
Follow the steps below to install the EAP with the provided accessories:
1Position the Ceiling T-rail Clip and push the
movable part toward the rail base.
Controller
Host
Router Switch Clients
Ceiling T-rail Clip M3×6 Pan-head Screws (Qty.5)
Internet
EAP
EAP
EAP

2
English
2Use an M3×6 pan-head screw to secure the T-rail
Clip onto the ceiling rail.
3Attach the mounting bracket to the Ceiling T-rail
Clip using four M3x6 pan-head screws.
4Make the Ethernet Cable pass through the fixing
hole of the mounting bracket. Connect the cable
to the ETHERNET port and attach the EAP to the
bracket.
5Push the EAP along the direction of arrows until
it locks into place. Then adjust the cable to make
the exposed part hidden behind the EAP.

3
English
■Option2：
Ceiling Mounting
Follow the steps below to install the EAP with the provided accessories:
1Remove the ceiling tile.
2Place the mounting bracket in the center of
the ceiling tile. Mark the four positions of
the screw holes and a hole for the Ethernet
cable to feed through. Drill four 4mm holes
for the screws and a 10mm hole for the
Ethernet cable.
X4
3Secure the mounting bracket to the ceiling
tile using four M3x30 pan-head screws,
washers and wing nuts.
Washers
(Qty.4)
M3×30 Pan-head Screws
(Qty.4)
Wing Nuts
(Qty.4)
Hole for Ethernet cable

4
English
4Feed the Ethernet cable through the hole.
Then set the ceiling tile back into place.
5Connect the Ethernet cable to the
ETHERNET port and push the EAP along
the direction of arrows until it locks into place.
Then adjust the cable to make the exposed
part hidden behind the EAP.
■Option3：
Wall Mounting
Follow the steps below to install the EAP with the provided accessories:
1If your Ethernet cable feeds through the wall,
you can position the mounting bracket to make
the cable through the fixing hole. Mark the four
positions of the screw holes and then drill four
6mm holes.
X4
2Insert the plastic wall anchors into the 6mm
holes.
M3×28 Plastic Wall Anchors
(Qty.4)
M3×20 Self-tapping Screws
(Qty.4)

5
English
3Secure the mounting bracket to the wall
by driving the self-tapping screws into the
anchors. Make sure that the shoulders of the
mounting bracket are on the outside.
4Connect the Ethernet cable to the ETHERNET
port on the EAP and attach the EAP to the
mounting bracket.
5Push the EAP along the direction of arrows
until it locks into place, and then adjust the
cable to make the exposed part hidden behind
the EAP.

6
English
Power Supply
EAP can be powered via a PSE device (such as a PoE switch) or a power adapter.
■Via PoE Switch
Connect the Ethernet cable from the PoE switch to the ETHERNET port.
■Via Power Adapter
Plug one end of the provided power adapter into the POWER port of the EAP and
the other end to a standard electrical wall outlet.
Switch
PoE Switch

7
Български
Забележка: Изображението може да се различава от реалния продукт.
Мрежова топология
Типична мрежова топология за EAP (точки за достъп с протокол за
разширена автентификация) е показана по-долу.
EAP Controller
Необходим е един DHCP сървър (в типичния случай - рутер) за задаване
на IP адреси на EAP устройствата и клиентите във вашата локална мрежа.
Един компютър, на който върви софтуера EAP Controller, който може да
бъде в същата или различна подмрежа с EAP устройствата, се използва за
централно управление на EAP устройствата.
Можете да получите софтуера EAP Controller от нашия уебсайт http://www.tp-
link.com.
Инсталация на хардуера
■Опция 1: Монтаж на релса на тавана
Следвайте стъпките, описани по-долу, за да инсталирате EAP с доставените
в комплекта аксесоари:
1Позиционирайте стягата за релса на тавана
и натиснете движещата се част към основата
на релсата.
Контролер
хост
Рутер Суич Клиенти
Стяга за Т-образна
релса на тавана
M3×6 винтове с глава тип
звезда (5 бр.)
Интернет
EAP
EAP
EAP

8
Български
2Използвайте един M3×6 винт звезда, за да
закрепите стягата към релсата на тавана.
3Закрепете монтажната скоба към стягата на
релсата на тавана с четири M3x6 винтове с
глава тип звезда.
4Прокарайте Ethernet кабела през фиксиращия
отвор на монтажната скоба. Свържете кабела
към ETHERNET порта и закрепете EAP
устройството към скобата.
5Натиснете ЕАР устройството по посоката на
стрелките, докато щракне на място, както
е посочено. След това нагласете кабела,
за да скриете подаващата се част зад ЕАР
устройството.