Transition Networks SISPM1040-384-LRT-C User manual

Transition Networks Install Guide SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 1of 49
SISPM1040-384-LRT-C and SISPM1040-362-LRT
Managed Hardened PoE+ Switches
SISPM1040-384-LRT-C SISPM1040-362-LRT
Install Guide
33727 Rev. B

Transition Networks Install Guide SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 2of 49
Safety Warnings and Cautions
These products are not intended for use in life support products where failure of a product could reasonably be
expected to result in death or personal injury. Anyone using this product in such an application without express
written consent of an officer of Transition Networks does so at their own risk, and agrees to fully indemnify
Transition Networks for any damages that may result from such use or sale.
Attention: this product, like all electronic products, uses semiconductors that can be damaged by ESD (electrostatic
discharge). Always observe appropriate precautions when handling.
NOTE: Emphasizes important information or calls your attention to related features or instructions.
WARNING: Alerts you to a potential hazard that could cause personal injury.
CAUTION: Alerts you to a potential hazard that could cause loss of data, or damage the system or equipment.
SISPM1040-384-LRT-C and SISPM1040-362-LRT Install Guide, 33727 Rev. B
Record of Revisions
Rev Date Description of Changes
A 6/22/17 Release at HW v1.01 and SW v7.10.
B 2/21/18 Update front panel art and text and add certification and compliance information. Add PoE information.
Trademark notice: All trademarks and registered trademarks are the property of their respective owners. All other
products or service names used in this publication are for identification purposes only, and may be trademarks or
registered trademarks of their respective companies. All other trademarks or registered trademarks mentioned
herein are the property of their respective holders.
Copyright restrictions: © 2017-2018 Transition Networks, Inc. All rights reserved. No part of this work may be
reproduced or used in any form or by any means (graphic, electronic, or mechanical) without written permission
from Transition Networks.
Address comments on this product or manual to:
Transition Networks Inc.
10900 Red Circle Drive, Minnetonka, MN 55343
tel: [phone] | toll free: 1.800.526.9267 | fax: [phone]
[email protected] | [e-mail] | [email protected]
web: https://www.transition.com

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 3of 49
Contents
Safety Warnings and Cautions................................................................................................................. 2
1. Introduction ................................................................................................................................... 5
Product Descriptions .................................................................................................................. 5
Ordering Information ................................................................................................................. 5
Manual Overview ....................................................................................................................... 5
Front Panel ................................................................................................................................. 6
LED Descriptions......................................................................................................................... 7
ALM (Alarm) LED................................................................................................................8
Front Panel 2-Position DIP Switch ............................................................................................ 10
Rings Support ........................................................................................................................... 11
RESET Button ............................................................................................................................ 12
Front Panel Ground Screw........................................................................................................ 12
2. Installing the Switch..................................................................................................................... 13
Package Contents ..................................................................................................................... 13
Unpacking................................................................................................................................. 13
Desktop Mounting.................................................................................................................... 13
DIN Rail Mounting .................................................................................................................... 14
Wall Mounting (Optional)......................................................................................................... 15
Connecting Ports ...................................................................................................................... 16
Installing SFP Modules.............................................................................................................. 16
Connecting to DC Power........................................................................................................... 17
Connecting the DI/DO Relay Wires........................................................................................... 18
3. Initial Switch Configuration.......................................................................................................... 19
Initial Switch Configuration via Web Browser .......................................................................... 19
Initial Switch Configuration Procedure ............................................................................19
Initial Switch Configuration via CLI ........................................................................................... 20
4. Troubleshooting........................................................................................................................... 21
Basic Troubleshooting .............................................................................................................. 21
Troubleshooting LED Indications .............................................................................................. 22
LED Summary............................................................................................................................ 23
PoE Modes and Compliance..................................................................................................... 24

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 4of 49
Troubleshooting PoE Problems................................................................................................. 26
Related Manuals....................................................................................................................... 28
Record Device and System Information ................................................................................... 29
Device Label and Packaging Label ............................................................................................ 30
5. Features and Specifications ......................................................................................................... 31
Key Features ............................................................................................................................. 31
Software Features..................................................................................................................... 33
MTBF Specifications ................................................................................................................. 36
Shared Features........................................................................................................................ 37
Shared Certifications and Compliance ..................................................................................... 38
Cable Specifications.................................................................................................................. 38
Power Supply Features and Specifications............................................................................... 39
Industrial Power Supply 25105................................................................................................. 39
Industrial Power Supply 25104................................................................................................. 40
Power Supply Built-in DC OK Relay Contact.....................................................................41
Power Supply Terminal Block Pin Number Assignments (TB1) ........................................41
Power Supply Terminal Block Pin Number Assignments (TB2) ........................................41
Power Supply Voltage Adjustment...................................................................................41
Power Supply Dimensions - 25104 (SDR-240-48).............................................................42
Dimensions (in mm) - 25104 (SDR-240-48)......................................................................42
6. Regulatory and Safety Information.............................................................................................. 43
Compliance and Safety Statements.......................................................................................... 43
Declaration of Conformity........................................................................................................ 43
High Risk Activities Disclaimer.................................................................................................. 44
Cautions and Warnings............................................................................................................. 44
Electrical Safety Warnings ........................................................................................................ 45
Class I Division 2 ....................................................................................................................... 46
7. Service, Warranty & Tech Support............................................................................................... 47
Warranty................................................................................................................................... 47
Contact Us ................................................................................................................................ 48

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 5of 49
1. Introduction
Product Descriptions
Transition Networks’SISPM1040-384-LRT-C is a fully managed PoE+ switch suitable for connecting and powering
devices in hardened environments. It can supply up to 30 Watts per port on all eight ports simultaneously.
Transition Networks’SISPM1040-362-LRT is a fully managed PoE+ switch suitable for connecting and powering
devices in hardened environments. It can supply up to 30 Watts per port on all four PoE ports simultaneously.
These switches include embedded Device Management System (DMS) software that provides the advanced
tools necessary for total management of all IP addressable devices. The unique DMS provides security
integrators with lower overall cost, less downtime and easier management of the entire PoE+ network.
These switches are hardened switches certified to operate reliably in harsh environments such as factory floors,
outdoor enclosures, or other challenging environments. These switches are appropriate for use in Hazardous
locations, Railway, Marine, Transportation, and Substation environments.
Ordering Information
#
Description
SISPM1040-362-LRT
Managed Hardened PoE+ Switch; provides (6) 10/100/1000Base-T PoE+ RJ45 ports +
(2) 100/100Base-X SFP ports and one RJ45 Console port.
SISPM1040-384-LRT-C
Managed Hardened PoE+ Switch; provides (8) 10/100/1000Base-T PoE+ RJ45 ports +
(4) 100/100Base-X SFP ports and one RJ45 Console port.
Optional Accessories
(sold separately)
25104
Optional Industrial Power Supply: Input: 85-264 VAC, 124-370 VDC.
Output: 48~55 VDC, 5.0A, 240 Watts.
25105
Optional Industrial Power Supply: Input: 85-264 VAC, 124-370 VDC.
Output: 48~55 VDC, 2.5A, 120 Watts
WMBH-01
Wall Mount Bracket for SISPM1040-384-LRT-C, SISPM1040-362-LRT
SFP Modules
Transition Networks offers a full line of small form factor pluggable (SFP)
transceivers. For more information, see the TN SFP webpage.
Manual Overview
This manual describes how to install, configure, and troubleshoot the PoE+ Switches, including how to:
•Install the switch
•Check switch status by reading the LED indicators
•Reset the switch to restore the switch to factory defaults
•Use a Web browser to initially configure the switch
•Troubleshoot the switch
The SISPM1040-362-LRT and SISPM1040-384-LRT-C differ mainly in port count as noted in this manual.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 6of 49
Front Panel
The switch front panel provides the ports, LEDs, DIP switch, RESET button, etc. as shown below.
Figure 1: Front Panel

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 7of 49
LED Descriptions
The front panel LEDs provide switch status as follows:
Power LEDs (P1 and P2): indicate whether the switch is powered up
correctly.
SYS (System) LED: indicates if the system is ready or not.
ALM (Alarm) LED: indicates if the system is operating normally.
RM (Ring Master) LED: indicates if Ring Master(s) or Slave is enabled.
RC (Rapid Chain) LED: indicates the status of the Rapid-Chain.
Port Status LEDs: indicate the current status of each port. Check these LEDs to determine the port status.
The following tables details the functions and descriptions of these LED indicators.
Table 1: Power LEDs
LED Color State Description
P1
(Power1) Green
On The switch is powered ON correctly.
Off The switch is not receiving power from power1.
P2
(Power2) Green
On The switch is powered ON correctly.
Off The switch is not receiving power from power2.
Table 2: System LED
LED Color State Description
SYS
(System) Green
On The switch is ready.
Off The switch is not ready.
Table 3: Alarm LED
LED Color State Description
ALM
(Alarm) Red
On An abnormal state, such as temperature, voltage, or DC
power1/2 was detected in the switch.
Off The system is normal.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 8of 49
ALM (Alarm) LED
The ALM (Alarm) LED lights if the monitored temperature or internal voltages are
exceeded.
Issue critical stage for High / Low Voltage alarm (Power A or B Voltage)
Lit Alarm LED in RED Color if Test-point (max) < Volts or if Test-point (min) < Volts.
V1 (PHY, TTL, LED, SFP): (max: 3.465V, min: 3.135V) (+- 5%)
V2 (MAC): (max: 2.625V, min: 2.375V) (+- 5%)
V3 (MAC, DDR): (max: 1.575V, min: 1.425V) (+- 5%)
V4 (MAC): (max: 1.05V, min: 0.95V) (+- 5%)
Issue critical stage for High Temperature alarm: Lit Alarm LED in RED Color if Test-point (max) < temperature
max: 100'C.
You can view temperature and voltage settings at Monitor > Port > SFP Detail Info.
You can you view and configure current trap event severity parameters via the Web Interface at Configuration >
System > Alarm Notification > Trap Event Severity.
You can use the more flash:TLV-config command to view the Factory alarm voltage and temperature:
SISPM1040-362-LRT# more flash:TLV-config
goldenkey
!
Factory hw-ver v1.01
!
Factory mech-ver v1.01
!
Factory platform-name IPGS-2708A
Factory poe-power 120
Factory alarm temperature 75 100
Factory alarm voltage 0.85 1.15 2.805 3.795 2.125 2.875 1.53 2.07
Factory fac-mac 00-40-C7-12-12-63
Factory serialno A084117AR0100003
!
end
SISPM1040-362-LRT#

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 9of 49
Check the port status by reading the LED behaviors per the table below.
Table 4: Port Status LEDs
LED Color State Description
RJ45
Ports
UP
Green On
The port is enabled and has established a link to connected device, and the
connection speed is 1000Mbps.
Green Blinking
The port is transmitting/receiving packets, and the connection speed is
1000Mbps.
Amber On
The port is enabled and has established a link to connected device, and the
connection speed is 10/100Mbps.
Amber Blinking
The port is transmitting/receiving packets, and the connection speed is
10/100Mbps.
-- Off
The port has no active network cable connected, or it has not established a
link to a connected device. Otherwise, the port may have been disabled via
the switch user interface.
RJ45
Ports
Down
Green On The port is enabled and supplying power to connected device.
Amber On An abnormal state, such as overload status, has been detected in the switch.
-- Off
The port has no active network cable connected, or it is not connected to a
PoE PD device. Otherwise, the port may have been disabled via the switch
user interface.
SFP
Ports
Green On
The port is enabled and has established a link to a connected device, and the
connection speed is 1000Mbps.
Green Blinking
The port is transmitting/receiving packets, and the connection speed is
1000Mbps.
Amber On
The port is enabled, has established a link to connected device, and the
connection speed is 100Mbps.
Amber Blinking
The port is transmitting/receiving packets, and the connection speed is
100Mbps.
-- Off
The port has no active network cable connected, or it has not established a
link to a connected device. Otherwise, the port may have been disabled via
the switch user interface.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 10 of 49
Table 5: RM (Ring Master) and RC (Rapid-Chain) LEDs
LED
RM (Ring Master)
RC (Rapid-Chain)
Off
disable
disable
Green
Ring Master is Enabled
Rapid-Chain (Active path)
Amber
Ring Slave is Enabled
Rapid-Chain (Backup path)
Blink Amber Error: More than one Master in this ring.
Error: Rapid-Chain Switch did not find the
other Rapid-Chain Switch partner (active &
backup).
Front Panel 2-Position DIP Switch
The DIP switches are used for Single Ring and Ring Failover quick settings as
described below. See the Web User Guide or the CLI Reference for more
information on Ring configuration and setup.
Table 6: DIP Switch Descriptions
RM RC R-Ring Settings Ring Port 1 Ring Port 2
RM (Ring
Master) LED
RC (Rapid-
Chain) LED
Off Off R-Ring Slave
Maximum Even
Port Number
Maximum Even
Port Number
Lit Amber Off
ON Off R-Ring Master
Maximum Odd
Port Number
Maximum Even
Port Number
Lit Green Off
Off ON R-Ring Failover Maximum odd
Port Number
Maximum Even
Port Number Off
Lit Green (Active
Path)
Lit Amber
(Backup Path)
ON ON
R-Ring Settings by
Software
-- -- -- --
1. The default DIP switch settings are both Off, meaning that Rings are configurable via the Web, telnet, and
Console.
2. Change the DIP switch settings to “deactivated” (both to ON), so that the software configuration is not
restricted.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 11 of 49
Rings Support
The switches support several Ring configurations:
1. Multiple Rapid Ring
2. Single Rapid Ring
3. Ring-to-Ring
4. Dual-Ring Configuration
5. Rapid Chain (Rapid Backup)
6. EPS (Ethernet Protection Switching) per ITU-T G.8031.
7. ERPS (Ethernet Ring Protection Switching) per ITU-T G.8032.
The DIP switches are used for Single Ring and Ring Failover quick settings (see DIP switch description above).
See the Web User Guide or the CLI Reference for more information.
Note that Spanning Tree must be disabled for Rapid Ring operation.
EPS and ERPS are standard protocols that can be used between various vendor switches.
Rapid Rings protocols are only for Transition Networks switches that support Rapid Rings protocols.
Notes:
1. The DIP Switches are only for Single Ring and Ring Failover.
2. DIP Switch settings have higher priority than software configuration.
3. Any Port can be configured as a Ring Connecting port.
4. The DIP switch can only set Single Ring and Rapid-Chain preferences.
5. Multiple Ring, Dual Ring, and Ring-to-Ring can only be set by software.
6. When the DIP Switch is not set to SW Mode, set DIP switch to Priority, By-pass SW.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 12 of 49
RESET Button
By pressing the RESET button for a specific amount of time, you can:
Reset the Switch: to reboot and get the switch back to the previous
configuration settings saved.
Restore the Switch to Factory Defaults: to restore the original factory default settings back to the switch.
Use the table below to determine which task is being performed by reading the LED behaviors while pressing
the RESET button. When the LED behaviors are correctly displayed, release the RESET button.
Table 7: RESET Button Description
Task to perform Press RESET for SYS LED Behavior Port Status LED Behavior
Reset the Switch 2 ~ 7 seconds Blinking Green ALL LEDs are Off.
Restore to Defaults 7 ~ 12 seconds Blinking Green ALL LEDs stay lit.
After you release the RESET button, wait a few moments for LED activity to stop.
Front Panel Ground Screw
The front panel grounding screw ( ) can be used for grounding.
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the ground screws to the grounding
surface prior to connecting devices.
ATTENTION:
This case must be earth grounded.
No DC input may be earth grounded.
Use Isolated Power Supply.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 13 of 49
2. Installing the Switch
Package Contents
Verify that you have received the items below. Contact your sales representative if any item is missing.
Please save the packaging for possible future use.
•One Switch
•One Terminal Block
•One printed Quick Start Guide (not shown)
•One DIN Rail mounting bracket and two screws
•One DB-9 to RJ-45 Console Cable
•Rubber Feet
•Power Supply (one or two; optional)
Unpacking
Unpack and verify the contents in their install location, and continue with one of the mounting procedures
below (Desktop, DIN Rail, or Wall mounting).
Desktop Mounting
1. Remove the Rubber feet from the adhesive.
2. Attach the feet to the four corners of the bottom of the switch.
3. Make sure the cables can reach the switch and that the switch is stable.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 14 of 49
DIN Rail Mounting
1. Attach the DIN Rail mounting kit to chassis back panel. Insert screws and tighten with a screwdriver.
Figure 2: Attaching DIN Rail Kit to the Switch
2. Insert the upper lip of the DIN rail into the DIN-rail mounting kit. Press the switch towards the DIN rail until it
snaps into place.
Figure 3: Insert switch to the DIN Rail
3. Make sure that the switch is attached securely to DIN Rail.
Figure 4: The switch attached to DIN Rail

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 15 of 49
Wall Mounting (Optional)
See the WMBH-01 manual for more details.
1. Attach the wall mounting plates to rear panel of the chassis. Insert screws and tighten then with a
screwdriver to secure the plates.
Figure 5: Attaching Wall Mounting Plates to the Switch
Figure 6: Wall Mounting Plate Dimensions
2. Install user-supplied screws on the appropriate location on the wall.
3. Make sure the switch is attached securely to wall.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 16 of 49
Connecting Ports
1. Connect the provided DB-9 to RJ-45 Console Cable to a PC or Terminal.
2. Connect the Ethernet RJ45 Ports to the Ethernet cables/far end devices. Only connect PDs which support
power input in 48~56V range to prevent damage to PDs.
Installing SFP Modules
On the SISPM1040-384-LRT-C, you can install or remove an SFP module from a SFP port without having to power
off the switch.
Note: Use UL Listed Transceiver SFPs rated 3.3Vdc, Laser Class 1. See the SFP manual for cautions and warnings.
1. Insert the module into the SFP port.
2. Press firmly to ensure that the module seats into the connector.
Figure 7: Installing an SFP Module into an SFP Port

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 17 of 49
Connecting to DC Power
The upper Euro Block provides DC Power Inputs P1 and P2. See Power Supply Features and Specifications on
page 37.
ATTENTION:
This case must be earth grounded.
No DC input may be earth grounded.
Use Isolated Power Supply.
1. Insert the negative/positive DC wires into the V- and V+ terminals, respectively.
2. To keep the DC wires from pulling loose, use a small flat-blade screwdriver to tighten the wire-clamp screws
on the front of the terminal block connector.
3. Insert the terminal block connector prongs into the terminal block receptor.
4. Insert the negative/positive DC wires into the power supply V- and V+ terminals and tighten. See Power
Supply Features and Specifications on page 37.
5. Plug the power supply into an appropriate AC outlet.
6. Check the SYS LED. If it is ON, the power connection is correct.
Figure 8: Connecting DC Power

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 18 of 49
Connecting the DI/DO Relay Wires
The lower Euro Block provides connection of the optional DI/DO Relay wires.
Figure 9: Connecting DI/DO Relay Wires
1. Insert the negative (ground)/positive DI/DO Relay wires into the +and -terminals, respectively.
2. To keep the DI/DO Relay wires from pulling loose, use a small flat-blade screwdriver to tighten the wire-
clamp screws on the front of the terminal block connector.
3. Insert the terminal block connector prongs into the terminal block receptor.
Notes:
Digital Output (relay): 24VDC/1A.
Digital Input: level 0 (Low) -> 0V to 6V, level 1 (High) -> 10V to 24V.
You can configure the normal modes of digital input/output (DI/DO) via the Web UI at the Home > Configuration
> System > Digital I/O page. See the Web User Guide.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 19 of 49
3. Initial Switch Configuration
Initial Switch Configuration via Web Browser
After powering up the switch for the first time, you can perform the initial switch configuration using a web
browser. For managing other switch features, refer to the Web User Guide for details.
To begin the initial configuration stage, you need to reconfigure your PC’s IP address and subnet mask to make
sure the PC can communicate with the switch. After changing PC’s IP address (for example, 192.168.1.250), then
you can access the Web interface of the switch using the switch’s default IP address as shown below.
Note: You can also skip step 1 to 3, by pressing WinKey+R and type ”ncpa.cpl” command to get to step 4
directly.
The initial switch configuration procedure is as follows:
□The factory default IP address is 192.168.1.77
□The factory default Subnet Mask is 255.255.255.0
Initial Switch Configuration Procedure
The initial switch configuration procedure is as follows:
1. Power up the PC that you will use for the initial configuration. Make sure the PC has the Ethernet RJ45
connector to be connected to the switch via standard Ethernet LAN cable.
2. Reconfigure the PC’s IP address and Subnet Mask as below, so that it can communicate with the switch.
The method to change the PC’s IP address (e.g., for a PC running Windows® 7/8.x/10) is as follows:
Step 1: Type “network and sharing“ into the Search box in the Start Menu
Step 2: Select Network and Sharing Center
Step 3: Click on Change adapter settings on the left of the PC screen.
Note: You can also skip step 1 to 3, by pressing WinKey+R and type ”ncpa.cpl” command to get to step 4
directly.
Step 4: Right-click on your local adapter and select Properties
Step 5: In the Local Area Connection Properties window highlight Internet Protocol Version 4 (TCP/IPv4)
then click the Properties button.
Step 6: Select the radio button Use the following IP address and enter in the IP for the PC (e.g. any IP
address not in use, and in between 192.168.1.2 and 192.168.1.254), Subnet mask (e.g.
255.255.255.0), and Default gateway that corresponds with your network setup. Then enter your
Preferred and Alternate DNS server addresses.
Step 7: Click OK to change the PC’s IP address.
3. Power up the switch for its initial configuration, and wait until it has finished its start-up processes.

Transition Networks Install Guide, SISPM1040-384-LRT-C & SISPM1040-362-LRT
33727 Rev. B https://www.transition.com Page 20 of 49
4. Connect the PC to any port on the switch using a standard Ethernet cable, and check the port LED on
the switch to make sure the link status of the PC’s is OK.
5. Run your Web browser on the PC, and enter the factory default IP address, to access the switch’s Web
interface.
If your PC is configured correctly, the login page of the switch displays as shown in Figure 10 below.
Figure 10: Web Interface Login page
If you do not see the above login page, please perform the following steps:
- Refresh the web page.
- Check if there is an IP conflict issue.
- Clean browser cookies and temporary Internet files.
- Check your PC settings again and repeat step 2.
6. Enter the factory default Username (admin) and Password (admin) on the Login page.
7. Click “Login” to log into the switch. The startup page displays; see the Web User Guide.
Note: The factory default Username (admin) and the factory default Password (admin) are case-sensitive.
Initial Switch Configuration via CLI
Use an RJ-45 cable to connect a terminal or PC/terminal emulator to the switch port to access the CLI.
Attach the RJ-45 serial port on the switch front panel to the cable for Telnet/CLI configuration.
Attach the other end of the DB-9 cable to a PC running Telnet or a terminal emulation program such as
HyperTerminal or TeraTerm.
After powering up the switch for the first time, you can perform the initial switch configuration using the CLI
(Command Line Interface). For managing other switch features, refer to the CLI Reference for details.