Travis Industries 99000154 User manual

Sturbridge Blower
(Part # 99000154)
Page 1 of 4 12/4/02 Travis Industries, Inc.
Compatibility
• Lopi Sturbridge Cast Gas Stove
Packing List:
• Blower • Blower Cover • Wiring Harness • Snap Disk • Power Cord • Strain Relief
• (4) Nuts & (4) Washers • (4) Grommets with Spacers • Rheostat Control Rod • 1/16” Hex Wrench
• Rheostat Knob • Remote Receiver Heat Shield (used only if using a remote)
Important Warnings
5 Turn the gas control valve to off and make sure the appliance has fully cooled prior to conducting service.
6 This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and
should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the
grounding prong from this plug.
Installation
1 Slide the thermodisk into the holder underneath the firebox.
Snap Disk Bracket
(attached to stove)
Snap Disk

Sturbridge Blower
(Part # 99000154)
Page 2 of 4 12/4/02 Travis Industries, Inc.
2 Attach the blower following the directions below.
Slide the fan mounting plate into
the slot on each of the rubber
grommets.
Fan Mounting Bracket
(attached to stove)
Rubber Grommet
(with spacer)
Nut
Slide the rubber grommets (with spacers inserted
inside) onto the fan mounting plate and attach
using the included washers and nuts.
Blower Mounting Bracket
11/32" Nutdriver
Washer
c
Attach the grommets (with spacers) to
the right side fan mounting bracket with
the included nuts and washers.
a
b

Sturbridge Blower
(Part # 99000154)
Page 3 of 4 4/8/04 Travis Industries, Inc.
3Attach the wiring harness following the directions below (do not plug in the power cord at this time).
Do not plug
the heater in
until
installation is
complete.
Attach the black and white wires
labeled “Blower” to the blower
(orientation does not matter).
11/32" Nutdriver
Remove one of the nuts holding
the blower in place. Insert the
screw through the eyelet on the
green ground wire and replace.
b
c
d
Route the wires labeled “Valve
on/off”and “Solenoid”under
the burner pan to a location
near the gas control valve (they
are for the optional modulating
remote).
a
Attach the two black wires
labeled “Snap Disk”to the
snap disk (orientation does
not matter).
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
f
e
Insert the molex connector on the power cord through the
hole on the blower cover and attach it to the molex
connector on the wiring harness. With the outer black
casing of the power cord 1" through the hole, install the
strain relief. The strain relief is best installed using pliers to
compress the two sides while pushing it into the hole.
Attach the two black wires labeled
“Rheostat”to the rheostat wires
(orientation does not matter).

Sturbridge Blower
(Part # 99000154)
Page 4 of 4 12/4/02 Travis Industries, Inc.
4Attach the blower cover and rheostat control rod (and knob) following the directions below. Make sure all of
the wiring is placed away from the blower impeller and the bottom of the burner. Use lock ties, if necessary,
to ensure no wires are damaged.
b
c
Remove the three screws used
to attach the blower cover from
the back of the stove.
a
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
1/16" Allen
Attach the
rheostat control
rod to the
rheostat.
Position the blower cover in
place from below, making sure
the rheostat control rod inserts
through the hole on the control
box.
Attach the rheostat knob.
1/4" Nutdriver
Rheostat Control Rod
Rheostat
d
5 Plug the blower in. Let the heater achieve operating temperature and test blower operation.
6If using a remote, use the included remote receiver heat shield as shown below.
If using the remote, place the
remote receiver inside the heat
shield and place the heat shield on
this ledge under the firebox.
Remote Heat Shield
NOTE: before installing,
bend these tabs up.