Travis Industries Lopi 99000123 User manual


Lopi Insert Fan
Installation Instructions
Page 1 of 3 17601771 - 10/10/2022 © Travis Industries, Inc.
Compatibility
SKU 99000123 – Answer Insert, Revere Insert, 1750 Insert, 1250 Insert
SKU 99000126 – Freedom Insert
SKU 99000132 – Evergreen Insert
Items Required
3/8” Nut Driver
Phillips Screwdriver

Standard Screwdriver
Slip Joint Pliers
(
if switchin
g
power cord to left side
)

Packing List
 BlowerAssembly
Air Control Extension Rod (99000132 ONLY) 
To Switch the Power Cord to the Left Side:
The power cord is installed on the right side from the factory. If you would rather have the cord on the left side of
the blower assembly, use a pair of slip-joint pliers to disconnect the strain-relief which holds the power cord in
place. With the power cord slackened, the Molex connectors that attach the power cord to the blower assembly
may be disconnected. Pry the push plug from the left side of the blower assembly and insert it into the hole on
the right side. Pull the left side Molex connector out from behind the deflection plate and cut the nylon tie that
holds the wire back. Insert the Molex connector on the power cord through the hole on the left side of the blower
assembly and attach it to the left side Molex connector. Route the wire directly behind the blower cage. Place the
strain-relief over the power cord (it should be in the same location on the power cord as before – approximately 2”
from where the wires split). Insert the strain-relief into the hole on the left side until the strain-relief locks in place.
Make sure the power cord, wires, or Molex assembly do not interfere with the movement of the impellers.
Remove the strain relief by
squeezing it from the top and
bottom with a pair of pliers.
Disconnect the Molex plug inside the blower
assembly. Remove the power cord by pulling
it out of the hole exposed by removing the
strain relief.
Remove the push plug from
the left side and insert it into
the hole on the ri
g
ht side.
Installation
1. Use a 3/8” nut driver to remove the
(2) mounting bolts from the front of
the insert

Lopi Insert Fan
Installation Instructions
Page 2 of 3 17601771 - 10/10/2022 © Travis Industries, Inc.
NOTE: This step is for the
Evergreen Insert Only. If
installing on a different appliance
skip to step #3.
2. Use a Phillips screwdriver to
remove the knob from the air
control rod on the appliance.
Screw the included 4" air
control extension rod onto the
air control rod and then install
the knob onto the end of the
extension (see right).
3. Remove the (2) Phillips
head screws that secure the
rheostat mounting plate to
the blower assembly (set
the screws aside for
reinstallation). Lift the
rheostat mounting plate out
of the way but leave the
wires connected. You will
now see the (2) holes on
the blower assembly used
to mount the assembly.
4. Place the blower assembly
into position under the
ashlip of the insert. Align
the mounting holes in the
blower assembly with the
holes in the insert. Secure
the blower assembly to the
insert using the mounting
bolts removed in step 1.
NOTE: Before tightening the screws with a 3/8” nut driver, lift the blower up so it tucks underneath the ashlip and
make sure no wires will be pinched.
5. Put the rheostat mounting
plate back in place and
secure it to the blower
assembly using the (2)
Phillips screws removed in
step 2.
6. Plug the power cord running from the blower into a grounded 110-volt electrical outlet.


Lopi Insert Fan
Installation Instructions
Page 3 of 3 17601771 - 10/10/2022 © Travis Industries, Inc.
Blower Operation
The blower will not start until the appliance is up to temperature, activating a thermodisk, which then
allows power to the motors. Once up to temperature, the blower will operate at the speed determined by
the position of the blower knob (see the illustration below). The blower will shut off automatically once the
appliance cools.
OFF
Turn the dial all the
way counter-clockwise
until it clicks off.
HIGH
The high position is all the
way counter-clockwise,
without clicking off.
LOW
Turn the dial a
l
the way
clockwise.