Travis Industries 99300687 User manual

GAS Fireplace, AGP Pellet Stove or GAS Insert Remote Control Installation Instructions
(LEAVE THE INSTRUCTIONS FOR THE HOMEOWNER)
The Thermostat Wall Wireless Transmitter is a six button transmitter, which turns the GAS Fireplace, AGP
Pellet Stove or GAS Insert ON/OFF manually or acts as a thermostat. The display of the transmitter shows
the clock, current room temperature, target temperature, timer setting, on/off status, low battery indicator and
“*child-proof*”.
Installation Precautions:
The Thermostat Wall Wireless Remote Control is tested safe when installed in accordance with this
installation manual. It is your responsibility to read all instruction before starting installation and to follow
these instructions carefully during installation.
The Thermostat Wall Wireless Remote Control MUST be installed by a qualified service technician.
The Thermostat Wall Wireless Remote Control is carefully engineered and MUST be installed only as
specified. If you modify it or any of its components, you may possibly cause a fire hazard.
FCC Requirements
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 to the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiver antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Canadian Equipment Requirements
This digital apparatus does not exceed the (class A/Class B)* limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le
present appareil numerique n'met pas de bruits radioelectriques depassant les limites applicables aux
appareils numeriques (de la class A/de la class B)* prescrites dans le Reglement sur le brouillage
radioelectrique edicte par le ministere des Communications du Canada.
This device complies with RSS-210 of Industry and Science Canada. Operation is subject to the following
two conditions : (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
All wiring should be done by a qualified electrician and shall be in compliance with local codes and with the
National Electirc Code ANSI/NFPA No. 70-current (In the United States), or with the current CSA C22.1
Canadian Electirc Code (in Canada).
Page 1 of 3
99300687
Thermostat Wall Wireless AGP Pellet Stove
GAS Fireplace, Pellet or GAS Insert Only

Page 2 of 3
1.0 Installation Instruction for AGP Pellet Stove
1.1 Installing the Receiver
1 Remove the side cover and access panel to both sides of the unit.
2 Remove the thermostat bracket and cover plate on the right side.
6 Program the receiver to the remote as per the instructions.
7 Replace access panels and side covers.
3Connect wires from the thermostat receiver to the wires labeled “TSTAT” from the main wire harness
on the left side of the unit (orientation does not matter).
4Attach the thermostat receiver to the thermostat bracket with 4 screws.
5 Replace the receiver and bracket into the cutout on the side of the unit (the cover plate can be
discarded).

Page 3 of 3
1.3 Installing the Remote wall mount Transmitter
1 Install the Wall Mount bracket horizontally onto the wall using the screws provided. See figure 4.
2 Slide the Wall Mount Transmitter onto the Wall Mount bracket as shown is figure 5.
figure 4
figure 5
AM
SET TEMP
F
ROOM TEMP
TIMER
Figure 3
FIREPLACE REMOTE
PRESS
TO OPEN
OFF
ON
REMOTE
BAT.LOW
PRESS
TO OPEN
BAT.LOW
OFF REMOTE ON
3 Installing the Remote Receiver to a Wall Mount:
- Secure the Remote Receiver to the wall mount.
- Use the screws provided to secure the face plate to the Remote Receiver. See Figure 2.
4 Put the switch cap to the slide switch.
5 Slide the battery compartment into the Remote Receiver. See Figure 3.
Figure 2
Installation of the
Receiver to a
Junction Box
FIREPLACE REMOTE
PRESS
TO OPEN
OFF
ON
REMOTE
BAT.LOW
1.2 Installing the Receiver for Gas Fireplace or Insert Wall Mount
1 Make sure the slide switch on the Remote Receiver is at the OFF position.
2 Gas Appliance Receiver Wire Installation (See Figure 1)
We recommend the receiver wires to be installed in a parallel circuit with the on/off switch (switch must
be in "OFF" position for remote to work). See the directions below for this type of installation..
Figure 1
Remove the
wires from the
on/off switch.
Attach the wires removed in
step "a" to the "Y" jumper wires
and attach the jumpers to the
on/off switch (orientation does
not matter).
Receiver
Wires
Back of
on/off switch
Attach the receiver wires to
the "Y" jumper wires
(orientation does not matter).
"Y" Jumper
Wires

Page 1 of 6
Figure 2
1.2 WALL MOUNT CHANGING BATTERIES: see Figure 2
BEFORE YOU BEGIN:
Warning Read all of the safety precautions in the owner's manual included with your GAS Fireplace,
AGP Pellet Stove or GAS Insert before using this remote control. The thermostat is not
intended for unattended use.
1.0 INSTALLING FRESH BATTERIES:
Note: It is not necessary to re-set your private code when Installing Fresh Batteries. The GAS
Fireplace, AGP Pellet Stove or GAS Insert MUST be OFF before replacing transmitter batteries.
Press and then Release
PRESS
TO OPEN
Fresh Alkaline
AAA Batteries.
AM
F
ROOM TEMP
TIMER
SET TEMP
Figure 1
Fresh Alkaline
AA Batteries.
PRESS
TO OPEN
Press and then Release (BATTERY COMPARTMENT)
1 The Remote WALL MOUNT uses 3 AAA-size batteries. Replace these batteries at least every 6 months
or when the Low battery indicator on the LCD is on.
2 Press the battery compartment slightly into the Remote WALL MOUNT and then release. The battery
compartment will pop out of the Remote WALL MOUNT.
3 Slide open the battery door and replace batteries.
4 Replace the battery door and slide the battery compartment back into the Remote WALL MOUNT.
5 After you take out the batteries, wait for at least 1 minute before putting fresh batteries into the Remote
WALL MOUNT and Receiver.
6 Use fresh alkaline batteries only.
1.1 RECEIVER CHANGING BATTERIES: see Figure 1
1 The Remote Receiver uses 4 pieces AA-size batteries. Slide the slide switch at the Remote Receiver to
the Off position.
2 Press the battery compartment slightly into the Remote Receiver and then release. The battery
compartment will pop out of the Remote Receiver.
3 Slide open the battery door and replace batteries.
4 Replace the battery door and slide the battery compartment back into the Remote Receiver.
99300687
Thermostat Wall Wireless AGP Pellet Stove
GAS Fireplace, Pellet or GAS Insert Only
GAS Fireplace, AGP Pellet Stove or GAS Insert Remote Control Operating Instructions For The Homeowner
Slide open the battery door

Page 2 of 6
A. Settings : see Figure 3
1 Press and hold clock button for about 2 seconds.
2 The hour display will flash. Use the Up and Down buttons to set the hour.
3 Press the clock button again and the minute display will flash. Use the Up and Down buttons to set the
minutes.
4 Press the clock button again and the oF or oC display will flash. Use the Up and Down button to select the
Remote Transmitter to display temperature in oF or oC.
5 Press the clock button again to exit setting.
2.0 OPERATION INSTRUCTIONS:
2.1 Wall Mount Transmitter Operation
The Thermostat Wall Wireless AGP Remote Control has 3 operating modes. They are: Manual, Auto and
Timer. Use the Up and Down buttons to set the target temperature between 45oF and 90 oF, or 8 oC and
32 oC.
WARNING: THE REMOTE WALL MOUNT WILL AUTOMATICALLY SWITCH OFF THE GAS Fireplace,
AGP Pellet Stove or GAS Insert WHEN THE BATTERIES IN THE REMOTE WALL MOUNT IS LOW.
B. Manual Mode: see Figure 4
1 Press the Manual On/Off button once to light the GAS Fireplace, AGP Pellet Stove or GAS Insert. Push the
button again to turn it off.
2 In Manual mode the Remote Transmitter will not turn the GAS Fireplace, AGP Pellet Stove or GAS Insert off
even if the room temperature exceeds the target temperature.
3 The GAS Fireplace, AGP Pellet Stove or GAS Insert will automatic turn off after 6 hours.
Fahrenheit or
Celsius display
"CLOCK"
button
Hour and minute
Display
"UP" and "DOWN"
buttons
Manual button
Figure 3
Figure 4

Page 3 of 6
E. Child-Proof Function : see Figure 7
1 There is a CHILD-PROOF switch at the back of the Remote Transmitter.
2 Slide the CHILD-PROOF switch to position marked C/P to activate the CHILD-PROOF function and the
child-proof function icon will appear on the LCD.
3 In CHILD-PROOF the Remote Transmitter will not operate the Remote Receiver until the "child-proof"
code is used or the switch is returned to the other position.
4 Press the Up and Down buttons in the following sequence: Up-Down-Down-Up-Down, within 2seconds,
button function will be temporarily restored, the child-proof function icon will disappear from the LCD.
5 If no button is pressed within 2 minutes, the Remote Transmitter will return to the Child-Proof function and
the child-proof function icon will reappear on the LCD until the Child-Proof switch is slide back to the
other position.
Set temperature
Adjust temperature
Control
1. Press the "TIMER" button the "---"
will start to flash.
2. Use the "UP" and "DOWN" buttons
to set the Time.
3. Press Manual or Auto On/Off
buttons to start the timer.
D. Timer Mode: see Figure 6
1 You can set the timer to the length of time you want the GAS Fireplace, AGP Pellet Stove or GAS Insert to
operate (1 to 120 minutes).
2 Press the "TIMER" button once. The Timer display "----" will blink.
3 Press the Up and Down buttons to set the timer. The LCD will display the time chosen.
4 The timer setting can be cancelled at any time by press and hold the "TIMER" button.
5 Press Manual or Auto On/Off button to turn on the GAS Fireplace, AGP Pellet Stove or GAS Insert.
6 The GAS Fireplace, AGP Pellet Stove or GAS Insert will turn off at the end of the timer setting.
C. Auto Mode: see Figure 5
1 Set the desired target temperature.
2 Press the Auto On/Off button once to activate the Auto mode. In Auto Mode the Remote Transmitter will
automatically turn on the GAS Fireplace, AGP Pellet Stove or GAS Insert when the room temperature is
below the target temperature and turn off the GAS Fireplace, AGP Pellet Stove or GAS Insert when the
room temperature is above the target temperature.
3 Press Auto On/Off button or Manual On/Off buttons to turn off the GAS Fireplace, AGP Pellet Stove or
GAS Insert (if it is already on) and exit Auto Mode.WARNING: IT TAKES SOME TIME FOR THE
RECEIVER TO RESPOND TO THE TRANSMITTER.DO NOT PRESS THE MANUALOR AUTO
ON/OFF BUTTONS MORE THAN ONCE WITHIN 2 SECONDS FOR CORRECT OPERATION.
Figure 5
Figure 6

2.2 RECEIVER OPERATION: see figure 8
The Remote Receiver has 3 operation modes. They are ON, OFF and Remote modes.
A. “ON” Mode: The Receiver will turn on the GAS Fireplace, AGP Pellet Stove or GAS Insert and not
responding to the
wall mount Transmitter.
B. “Remote” Mode:
The Receiver will respond to the Wall Mount Transmitter and turn the Fireplace, Pellet
Stove or Insert on and off accordingly.
C. “OFF” Mode: The Receiver will Close the GAS Fireplace, AGP Pellet Stove or GAS Insert and not
responding to the wall mount Transmitter .
GAS Fireplace, AGP Pellet Stove or
GAS Insert Controlled by Remote
GAS Fireplace, AGP Pellet Stove
or GAS Insert Off
GAS Fireplace, AGP Pellet Stove
or GAS Insert On
Low Battery
Indicator
OFF REMOTE ON
BAT.LOW
PRESS TO OPEN
OFF REMOTE ON
BAT.LOW
PRESS TO OPEN
OFF REMOTE ON
BAT.LOW
PRESS TO OPEN
Figure 8
Figure 7
ATTENTION: IMPORTANT SAFETY FEATURE see figure 9
6HR Safety Timer(FACTORY DEFAULT IS “ON”)
Enable - Timer Set to “ON”
In case of Transmitter failure (Malfunction / Battery run out) or out of transmission range, The Receiver will
shut down the GAS Fireplace, AGP Pellet Stove or GAS Insert automatically after 6Hr of no Transmitter
signal detection.
Disable - Timer Set to “OFF”
The Receiver & GAS Fireplace, AGP Pellet Stove or GAS Insert will continue operate in the last setting and
will not shut off automatically even in case of Transmitter failure. (Note: Not recommended)
Figure 9
TIMER
ON OFF
6Hr
First 2Hr since last
signal received Following 4Hr 6
th
Hr since last
signal received
ON Intermittent and
Check For Transmitter Signal
Shut down if no
signal received
NOTE: AUTO MODE ONLY
Page 4 of 6
To unlock Child-Proof, press.
UP-DOWN-DOWN-UP-DOWN
Child-Proof off
Child-Proof on
C-P
C-P
The words "Child-Proof"
appear here when Child-
Proof feature is turned on.
The words "Child-Proof" will
disappear from the LCD.
The "Child-Proof " will
disappear from the LCD.
C-P
1 2 3 4 5 6
DIPON
Receiver / GAS
Fireplace, AGP Pellet
Stove or GAS Insert
Status

3.1 Coding Instructions: see figure 11
1 There are code switches at the back of the Remote Wall Mount. Slide the code switches to you choice of
ON or OFF positions. FACTORY SETTING IS ALL 'OFF'.
2 Make sure the slide switch on the Remote Receiver is at the OFF position.
3 Take the Remote Wall Mount close to the GAS Fireplace, AGP Pellet Stove or GAS Insert or the Remote
Receiver (less than 2-10 feet from the GAS Fireplace, AGP Pellet Stove or GAS Insert or Remote
Receiver is recommended.)
4 Slide the slide switch on the Remote Receiver to REMOTE position.
5 Install fresh AAA alkaline batteries into the Remote Wall Mount.
6 Press any button on the Remote Wall Mount. The Remote Receiver will produce a 'beep' sound when it
receives the code from the Remote Wall Mount. The system is now ready to operate.
7 If you do not hear a 'beep' sound from the Remote Receiver, removes batteries from the Remote Wall
Mount and slide the slide switch on the remote receiver to OFF position, wait for 1 minute, and repeat
step 3 to 6.
8 If you desire to operate multiple Remote Receivers with the one Remote Wall Mount, continue to hold the
button on the Remote Wall Mount as you bring the Remote Wall Mount within 5 feet of each Remote
Receiver then slide the slide switch on the Remote Receivers to the REMOTE position. Each will
acknowledge receipt of coding with a beep.
Page 5 of 6
RECEIVED,
FCC ID:EPK10305
Acumen
IC:2887A-10305
INTERFERENCE AND
(1) THIS DEVICE MAY NOT CAUSE
(2) THIS DEVICE
INTERFERENCE THAT MAY CAUSE
Model No.: WMT103
HARMFUL
TWO CONDITIONS:
MUST ACCEPT ANY INTERFERENCE
UNDESIRED OPERATION.
INCLUDING
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING
Figure10
3.0 IMPORTANT SAFETY FEATURE: See Figure 10.
You can set a private code into your system to prevent accidental operation by another transmitter nearby.
Note: User must repeat SET PRIVATE CODE every time they change the code.
Switch Receiver
to Remote
2'~10'
Figure 11
Select Code
Position
1 2 3 4 5 6
ON
Switch off
the Receiver
Install 3AAA Batteries
C-P
1 2 3 4 5 6
DIPON
Install 4AA Batteries
BAT.LOW
OFF REMOTE ON
BAT.LOW
OFF REMOTE ON

Page 6 of 6
FCC Requirements
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 to the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiver antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio TV technician for help.
Canadian Equipment Requirements
This digital apparatus does not exceed the (class A/Class B)* limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le
present appareil numerique n'met pas de bruits radioelectriques depassant les limites applicables aux
appareils numeriques (de la class A/de la class B)* prescrites dans le Reglement sur le brouillage
radioelectrique edicte par le ministere des Communications du Canada.
This device complies with RSS-210 of Industry and Science Canada. Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
All wiring should be done by a qualified electrician and shall be in compliance with local codes and with the
National Electirc Code ANSI/NFPA No. 70-current (In the United States), or with the current CSA C22.1
Canadian Electirc Code (in Canada).