Trevi 211 User manual

Dear Customer
Congratulations! You have purchased a pool of superior quality and durability. To achieve the best possible results,
follow the instructions carefully. Failure to follow the installation procedures may result in damage to your pool or
property and void your warranty. We recommend that you make a preliminary study of the instruction booklet to
familiarize yourself with the different parts of your pool. Make sure that you understand each step thoroughly before
you begin assembling.
We wish you a most pleasant and refreshing summer.
We strongly recommend having your pool installed by a professional.
WARNING: Be sure you have read and understand the “Safety Information” sheets
before you begin your pool installation.
WARNING: For your safety, your pool is not designed for diving and/or jumping head first.
Please do not dive. Diving may result in permanent injury or death.
ASSEMBLY INSTRUCTIONS
OVAL POOLS
WITH SIDE SUPPORTS
Trevi 211 / 213
SITE PREPARATION
1
Chart 1.1 - Grass removal area (Figure 1.1)
1.67m (5' 6")
1.67m (5' 6")
3.35m (11')
3.35m (11')
6.09m (20' 0")
7.01m (23' 0")
2.99m (9' 10")
3.91m (12' 10")
10'x19' 2.75m (9' 0")
10'x22' 3.65m (12' 0")
1.67m (5' 6") 3.35m (11') 5.18m (17' 0") 2.08m (6' 10")
10'x16' 1.82m (6' 0")
2.43m (8' )
2.89m (9' 6")
4.87m (16')
5.79m (19')
9.44m (31' 0")
10.36m (34' 0")
4.82m (15' 10")
4.82m (15' 10")
15'x30' 4.57m (15' 0")
18'x33' 4.57m (15' 0")
1.98m (6' 6")
2.43m (8' )
3.96m (13')
4.87m (16') 7.62m (25' 0")
3.91m (12' 10")
2.99m (9' 10")
12'x24' 3.65m (12' 0")
15'x24' 2.75m (9' 0")
1.98m (6' 6") 3.96m (13') 5.79m (19' 0") 2.08m (6' 10")
12'x18' 1.82m (6' 0")
7.62m (25' 0")
MODEL
DISTANCE (A-B) RADIUS (R) WIDTH (D) TOTAL LENGHT (E) CORRIDOR (F)
1.98m (6' 6") 3.96m (13')6.70m (22' 0") 2.99m (9' 10")
12'x21' 2.75m (9' 0")
When selecting the site for your pool, take into account city by-laws regarding fences and utilities laws pertaining to electrical cables
as well as the landscaping which you are planning once the pool is installed.
40317_ V4_2021-05-23
A-FRAME

Chart: Sand quantity
1) Drive a stake into the ground at points A and B respecting the
distance of the straight section between those two points (A-B).
2) Draw two half circles respecting the radius (R).
3) Join the two half circles with straight lines respecting the width
between these two lines (D).
4) Verify that the total length is consistent. (E)
5) Add 89cm (36”) wide trenches on each side, respecting the
length (F)
6) Remove all grass from the area you have just outlined.
SITE PREPARATION (continued)
1
SITE LEVELLING
2
AB
A-B
R
R
D
91cm(36”)
E
F
POOL WALL
AREA TO OUTLINE
Figure 1.1
SITE LEVELLING
For an oval pool, the bottom must absolutely be levelled, using a
carpenter's level and a straight plank. Eliminate any protrusions.
Ensure that the surface is free of debris such as rocks, wood, etc.
TRENCHES FOR BUTTRESS ASSEMBLIES
1) Dig trenches to a depth equal to the thickness of the patio blocks
(2” thick slabs recommended). (Refer to illustrations for trench lay-
out details).
2) Make sure trenches are smooth and leveled without compacting
them.
3) Place and level patio blocks into trenches. Make sure that the
top of the slab is level with the pool area. And bottom of framework
must be level with pool area.
In order to ensure proper water drainage around the pool, a 2-degree
slope needs to be erected around the perimeter of the pool. THE
MANUFACTURER WILL NOT BE HELD RESPONSIBLE FOR ANY LI-
ABILITY SHOULD THIS STEP BE OMITTED.
10x16, 10x19 10x22, 12x18, 12x21, 12x24 15x24, 15x30 18x33

Dig a hole 30 cm (12") wide by approximately 25 cm (10") deep in
the center of the circumference.
From the center hole to the projected location of the pool motor, dig
a 15 cm (6") wide trench. Place the removed soil aside to be used
later to cover the hose.
Bottom Drain Assembly
Place teflon tape around the threaded plug. Screw in drain holes
using large pliers. Glue the connector in the appropriate opening.
Take one of the two rubber rings and adjust it to the top of the drain,
aligning the holes carefully. Secure with strips of adhesive tape to
prevent sand from penetrating inside the holes once the drain has
been installed.
Secure one end of the long black or white hose inside the drain
spout. First apply glue on the drain spout and inside the drain end,
then secure with one or two collars.
Cut the hose so that it ends with the stone dust (or sand). Measure
the pool radius from the center of the drain, then add 15 cm (6").
Place the assembled bottom drain in the hole so that it is approxi-
mately 1.3cm (1/2") higher than the surface soil. Bury the hose,
levelling the drain as much as possible. Compact the soil, using
your feet and a tampering tool as well.
Mix three (3) shovels of stone or sand dust with one half shovel of
pure cement, adding a small quantity of water, then pour the cement
around the drain until it reaches 1.3 cm (1/2") from the top.
BOTTOM DRAIN ASSEMBLY (if applicable)
3
1) Study illustrations and chart carefully. You are now ready to as-
semble the metallic tension straps. Refer to indications on the chart
for the exact number of tension straps per row according to their
respective pool size.
TENSION STRAPS ASSEMLBY
4
Chart
345 66
333 45
91215 2430
354
334
91516
POOL SIZE 10x16 10x19 10x22 15x30 18x33
ROWSTOASSEMBLE
TENSION STRAPSQUANTITY (TOTAL)
STRAPSPERROW
12x18 12x21 15x24
4
3
12
12x24

1) Refer to Illustration 5.1. Assemble the buttress post to the
bottom brace using two (2) bolts and nuts (BB) 1/4"#20 X 5/8"
(6,35 mm X 15,88 mm).
2) Refer to Illustration 5.2. Assemble the lower part of the angle
brace using bolts and nuts 1/2" X 1" (12,7 mm X 25,4 mm) and
four (4) washers, two on each side.
Remember to insert one washer between the bottom brace and the
angle brace.
Next, assemble the other side of the angle brace to the buttress post
with two (2) bolts ans nuts (BB)1/4" #20 X 5/8" (6,35 mm X 15,88
mm).
TENSION STRAPS ASSEMLBY (continued)
4
2) Refer to Illustration 4.1: If there is more than one metallic
strap per row, assemble the straps together using 4 bolts and nuts
(BB) 1/4" #20 X 5/8" (6,35 mm X 15,88 mm), taking care of plac-
ing the bolt head on top.
3) Refer to Illustration 4.2.: Attach the assembled tension straps
to bottom braces on both sides, using four (4) bolts and nuts (BB)
1/4" #20 X 5/8" (6,35 mm X 15,88 mm), taking care of placing
the bolt head on top.
BUTTRESS POSTS ASSEMBLY
5
STRAPS
BOLT 1/4”X 5/8”
NUT 1/4”
BOTTOM BRACE
PATIO BLOCK
BOLT 1/4”-20X 5/8”
NUT 1/4”
STRAPS
BOTTOM
BRACE
Illustration 4.1 Illustration 4.2
PATIOBOCK
BOLT 1/4”-20X 5/8”
NUT 1/4”
BUTTRESS
POST
BOTTOM
BRACE
Illustration 5.1
BOLT 1/4”-20X 5/8”
NUT 1/4”
BUTTRESS
POST
BOTTOM
BRACE
NUT 1/2”BOLT 1/2”X 1”
WASHER
WASHER
ANGLE
BRACE
Illustration 5.2
Donot use impact guntoscrew thetension straps.
Minimumtorqueforceof 60inch
poundstomaximumof 85 inch pounds.

SHORT
END
1STBOTTOM TRACK
ROUNDSECTION
1ST BOTTOM PLATE
ROUNDSECTION
LONGEND
BOTTOM TRACK SHORT END
FASTENER
BOLT
1/4”-20X 5/8”
NUT 1/4”
Illustration 7.1
*Resin track 211 only.
1) Position the buttress posts assembled in step 5 on the patio
blocks in the trenches previously placed.
2) Refer to Illustration 6.1 : Once the buttress posts are placed
on the patio blocks, assemble the bearing plate in front of the but-
tress posts and on the tension straps. Fix the bearing plate using
eight (8) bolts and nuts (BB) 1/4"#20 X 5/8" (6,35 mm X 15,88
mm), taking care of placing the bolt head on bearing plate and nut
on buttress post.
BEARING PLATE ASSEMBLY
6
Start with round section, refer to illustration 7.1 :
Assemble the track fastener at the bottom of the four buttress posts
with bolt and nut 1/4" #20 X 5/8" (6,35 mm X 15,88 mm).
Inset the short end of the first round section bottom track in the fas-
tener at the bottom of the last buttress post of the straight section.
Place the first bottom plate of the round section, at the other end of
the bottom track.
Round section, refer to Illustration 7.2 :
Using the round section bottom tracks and the bottom plates, start
with the first plate of the round section. Repeat this procedure until
the half circle is completed.
Refer to Illustration 7.3. :
Before going to the next step, make sure that the centre of the pool
is properly squared and the metallic tension straps are straight with
no buckles.
ROUND SECTION BOTTOM TRACKS ASSEMBLY
7
Illustration 7.3
Illustration 6.1
Illustration 7.2

WALL INSTALLATION
8
Add sand.
Choose the filter location beside a round section (never in a straight
section). The starting point should be at that location where the
skimmer and return holes are, and as close as possible to the fil-
tration system. When installing the steel wall, it is important to
do so in a location protected from the wind or on a day without
any wind.
Before uncoiling the wall, make sure the pre-punched holes for the
skimmer and pump return are at the top and facing the planned lo-
cation of your filter.
End
BOTTOM PLATE
Begin inserting the wall into the bottom tracks in the middle of a
bottom plate. At first, the wall is kept in place with one or two stakes
and strings (or extra persons). One person uncoils the wall on a
beam or a plank, while a second person inserts it in the bottom
tracks. Do not uncoil more than 3 m (10') of wall before you install
a support bar or stake and string to reinforce the structure.
Once the wall is completely uncoiled, you may find that it is too
long or that both ends do not meet by a few centimetres. If such is
the case, adjust tracks and bottom plates until wall holes line up. If
this does not work, roll up the wall again, check measurements as
per Illustrition 1.1, adjust tracks and plates, if applicable, and uncoil
the wall again. If the spread is too wide, measure the wall and check
it against the chart below.
Join both ends of the wall by orienting folds outward to hide the ex-
clamation icon. (Illustration 8.1)
Note: If the wall is attached properly, you should no longer see
the exclamation icon. If you can always see the icon, you must
reverse the overlap.
Insert bolts and nuts in every hole and tighten with wrench (screw
head on water side of wall). Tape over screw heads with duck tape.
Chart
Illustration 8.1
Donot use impact gunfor wall
screws.
Minimumtorqueforceof 60inch
poundstomaximumof 85 inch pounds.
Outsideof pool
Insideof pool
Fold
Fold
BOLT End
Start
NUT
Insideof pool
Outsideof pool
!
IMPORTANT! Installing the wall joint in non-compliance with the specifications dictated by the manufacturer will void the warranty.
A
faulty installation will cause the wall/joint to split which could result in serious and/or fatal injuries!
MODELS10x16 18x33
ACTUAL LENGHT
OF THE WALL
10x19 10x22 12x18 12x24 15x24 15x30
43' 8" 49' 8" 55' 9" 49' 81/2" 61' 93/8" 77' 21/2" 86' 71/2"
(13,30m)(15,14m)(17,00m)(15,16m)(18,83m)(19,88m)(23,53m)(26,40m)
65' 21/2"
12x21
55' 93/8"
(17,00m)
PLANKS
ST
SAND
TA
AKESAND
STRINGS
DET
TA
AIL 8.1

You can now spread approximately 10 cm (4") of compacting sand
all around the inside base of the wall in order to protect the liner
from the cutting edges of the bottom tracks and the stone dust (if
applicable), or install a prefabricated cove if available.
SAND BASE FINISHING
Level finishing sand one last time. Make sure that any sharp stones,
debris or roots have been removed from the surface. For better pro-
tection, spray sand with water and pack it once more until the base
is nicely even.
SAND BASE FINISHING
9
Before pulling the liner up against the wall, insert a vacuum cleaner
hose down into the pump return hole to approximately 15 cm (6")
from the ground.
Maintain the hose in place with adhesive tape. Don't forget to block
the skimmer hole with adhesive tape to prevent air from leaking in.
Place the unfolded liner in the center of the pool area at right angles
with the skimmer hole. Make sure you wear light, flat-soled shoes
to walk on the sand as the slightest heel mark could be visible once
the pool is filled.
Carefully unfold the liner, bringing the bottom-sidewall seam close
to the wall base. Make sure that the side with the protruding seams
faces downward or that the patterned side faces upward.
Lift up a section of the liner over the top of the wall leaving a 10 cm
to 15 cm (4" to 6") fringe outside the wall. Secure the liner with a
plastic coupler (sold separately). Install the top track on the wall
then install the top plates on top of each upright.
At this point, the liner may be too tight, making it difficult to drape
the overlap or, on the contrary, too loose. In such cases, you will
have to redistribute the tension in the liner by removing some of the
couplers and readjusting the liner.
VINYL LINER INSTALLATION
10
LINER
WALL
30 cm (12")
10 cm (4")
SAND COVE
(or PREFAB COVE) BOTTOM
TRACK
PUMP RETURN HOLE
VACUUM CLEANER
INNER WALL
GROUND LEVEL
15 cm (6")
OVERLAP
LINER
RESIN TOP
TRACK
WALL
PLASTIC
COUPLER
(SOLDSEPARATELY)
STEEL
TOPTRACK
PLASTIC
COUPLER
(SOLDSEPARATELY)
211 213

VINYL LINER INSTALLATION (continued)
10
Installation detail of a bead liner with top track.
Hang the liner on the top of the wall and install the top track to se-
cure.
Start the vacuum cleaner to allow the liner to adhere to the wall and
check for excess tension at the bottom or for wrinkles. Adjust the
liner by removing wrinkles if needed, lift or lower it in order to ensure
a perfect fit.
Fill the pool with water up to the base of the wall before stopping
and removing the vacuum cleaner.
PUMP RETURN FITTING
After you remove the vacuum cleaner, you may install the return fit-
ting. Place the return fitting ring against the liner and adjust it so
that it is perfectly aligned with the hole in the wall. When the ring is
properly positioned and secured, cut the liner in the middle of the
ring.
Insert the return fitting from the inside, placing the first gasket be-
tween the return fitting and the liner and the second between the
wall and the liner. Then tighten the outside ring with large pliers, tak-
ing care not to crease the liner.
BOTTOM DRAIN (optional)
Find the holes through the middle of the liner and screw the ring
and gasket in against the liner before cutting the liner in the middle
of the ring, then screw on the drain cover.
UPRIGHT POST TOP PLATE (round section)
11
U-BEAD
LINER
RESIN TOP
TRACK
WALL
STEEL
TOPTRACK
Put the top plate on the upper side of the upright, and se-
cure with two (2) screws “Z” on each side.
‘’Z’’
SCREW
UPRIGHT
TOP
PLATE
211 213

UPRIGHT POST INSTALLATION
12
For the round section:
Attach the uprights to the bottom plate with two (2) screws “Z”,
which you will find in the hardware bag.
Uprights must be installed outside the flanged part of the bottom
plate and into the two notchs of the bottom track.
TOP SEAT INSTALLATION
13
Be sure to have a vertical (plumb) upright before fixing the top seat.
Place the top seat on the upper side of the upright.
Center the top seat between the two uprights and secure with four
(4) screws “Z”.
‘’Z’’
SCREW
BOTTOM
PLATE
‘’Z’’SCREW

SEAT CAP INSTALLATION
14
Put the seat cap on the inside section of the seat and interlock with
the upright. Secure the seat cap with one (1) screw “Z”.
Snap the solar cap on top of the seat cap and interlock it on the bot-
tom.
SECURITY LABELS INSTALLATION
15
SEAT CAP
TOP SEAT
SOLAR
CAP
SEAT CAP
‘’Z’’
SCREW
TOP SEAT
Install the four (4) safety labels (DANGER) supplied with your pool
as follows: two (2) labels visible at the entrance to the pool and two
(2) visible at the main access of the backyard.
Important: if you require additional labels, please contact us at
Trevipools.com
Install a minimum of three (3) safety labels (supplied with the liner)
inside the pool so that at least one label is visible no matter where
the bather enters the water (see drawing for positionning)
LABEL

FILTRATION SYSTEM ASSEMBLY
16
PARTS LIST
17
* SEE DRAWING PARTS NEXT PAGE
Assemble skimmer, inlet, drain, filter, pumps, hoses according to separate
manufacturer’s instructions.
Note: See 'Safety Information" Manual.
NOTE: Please confirm quantities with checklist included in each box.
POOL WALL (finishedlenght, inch)
BOLT & NUT FOR52" (OR54")WALL
POOL LINER
PLASTICCOUPLER(SOLDSEPARATELY)
TOPSEAT - ROUNDSECTION
TOPSEAT- STRAIGHT SECTION
BOTTOM PLATE
UPRIGHT 52'' orUPRIGHT 54''
TOPPLATE - ROUNDSECTION
SEAT CAP
TOPTRACK - ROUNDSECTION
TOPTRACK - STRAIGHT SECTION
BUTTRESS ASSEMBLY
BUTTRESS POST
TOPPLATE -
STRAIGHT SECTION
NUT 1/2" (12,7 mm)
WASHER1/2" (12,7 mm)
TENSION STRAP
1/4" #20X 5/8" (6,35mm X 15,88 mm)SCREW & FLANGE NUT
STANDARDSCREW (SCREW #14 ,1" LENGHT)
ITEMDESCRIPTION
AA
BB
CC
DD
A
B
C
D
E
F
G
J
L
O
P
Q
R
S
U
UU
V
X
Y
BB
Z
SEAT CAPEXTENSION - STRAIGHT SECTION
N
SOLARCAP
H
BOTTOM BRACE
ANGLE BRACE
BEARINGPLATE
BOLT 1/2" X 1" (12.7mm X 25.4 mm)
PATIOBLOCK
BOTTOM TRACK - ROUNDSECTION
TRACK FASTENER
K

U
O
Z
Q
V
B
L
S
R
F
UU
N
Y
X
BB
Z
P
Z
BB
BB
BB
BB
H
K
PARTS LIST
18
H
AA
F
G
Z
Z
Z
Z
CC
DD
D
BB
ROUND SECTION STRAIGHT SECTION
BB Z U
UU V