Trevi 228 User manual

When selecting the site for your pool, take into account city by-
laws regarding fences and utilities laws pertaining to electrical
cables as well as the landscaping which you are planning once
the pool is installed.
1) Drive a stake into the ground at points A and B respecting the
distance of the straight section between those two points (A-B).
It is important that your A and B measurements are exact to chart
1.1 to ensure proper installation and avoid problems further on.
2) Draw two half circles respecting the radius (R).
3) Join the two half circles with straight lines respecting the width
between these two lines (D).
4) Verify that the total length is consistent. (E)
5) Add 6”(15cm) wide trenches on each side, respecting the
length (F)
6) Remove all sod from the area you have just outlined.
Dear Customer
Congratulations! You have purchased a pool of superior quality and durability. To achieve the best possible results,
follow the instructions carefully. Failure to follow the installation procedures may result in damage to your pool or
property and void your warranty. We recommend that you make a preliminary study of the instruction booklet to
familiarize yourself with the different parts of your pool. Make sure that you understand each step thoroughly before
you begin assembling.
We wish you a most pleasant and refreshing summer.
We strongly recommend having your pool installed by a professional.
WARNING: Be sure you have read and understand the “Safety Information” sheets
before you begin your pool installation.
WARNING: For your safety, your pool is not designed for diving and/or jumping head first.
Please do not dive. Diving may result in permanent injury or death.
ASSEMBLY INSTRUCTIONS
OVAL POOLS NBS
Trevi 228/230/248/250/278/280
SITE PREPARATION
1
E
F
A-B
R
R
POOL WALL (dash line)
AREA TO OUTLINE
SOD REMOVAL
D
6” (15 cm)
6” (15 cm)
Figure 1.1
Chart 1.1 - Grass removal area (Figure 1.1)
1.67m (5' 6")
1.67m (5' 6")
3.35m (11')
3.35m (11')
6.09m(20' 0")
7.01m (23' 0")
2.99m(9' 10")
3.91m (12' 10")
10'x19'2.75m (9' 0")
10'x22'3.65m (12' 0")
1.67m (5' 6")3.35m (11')5.18m (17' 0")2.08m (6' 10")
10'x16'1.82m (6' 0")
2.43m (8' )
2.89m(9' 6")
4.87m (16')
5.79m(19')
9.44m(31' 0")
10.36m (34' 0")
4.82m (15' 10")
4.82m (15' 10")
15'x30' 4.57m (15' 0")
18'x33'4.57m (15' 0")
1.98m (6' 6")
2.43m (8' )
3.96m (13')
4.87m (16')7.62m (25' 0")
3.91m (12' 10")
2.99m(9' 10")
12'x24' 3.65m (12' 0")
15'x24' 2.75m (9' 0")
1.98m (6' 6")3.96m (13')5.79m(19' 0")2.08m (6' 10")
12'x18'1.82m (6' 0")
7.62m (25' 0")
MODEL
DISTANCE (A-B) RADIUS (R) WIDTH (D) TOTAL LENGHT (E) CORRIDOR (F)
1.98m (6' 6")3.96m (13')6.70m(22' 0")2.99m(9' 10")
12'x21'2.75m (9' 0")
40305_ V7_2022-05-27
NBS

SITE LEVELLING
2
SITE LEVELLING
For an oval pool, the bottom must absolutely be levelled, using a
carpenter's level and a straight plank. Eliminate any protrusions.
Ensure that the surface is free of debris such as rocks, wood, etc.
TRENCHES FOR BUTTRESS ASSEMBLIES
1) Dig trenches to a depth equal to the thickness of the patio blocks
(2” thick slabs recommended) and the thickness of the buttress
assembly beam 8cm (3 1/4”).
(Refer to illustrations for trench layout details).
2) Make sure trenches are smooth and leveled without compacting
them.
3) Place and level patio blocks into trenches. Make sure that the
top of the slab is 8cm (3 1/4”) deep. Top of framework must be
level with pool area.
Chart: Sand quantity
3.05 mx 6.70 m(10’ x 22’)2Tons 1 Ton
3.05 mx 5.79m(10’ x 19’)2Tons 1 Ton
3.05 mx 4.87 m(10’ x 16’)2Tons 1 Ton
3.65mx 6.40m(12’ x 21’)2Tons 1 Ton
2Tons
3.65mx 5.48m(12’ x 18’)2Tons 1 Ton
10" 10" 10"
(25cm) (25cm) (25cm) (25cm)
118" (299 cm)
48" (121cm) (12x21)
10"
3-1/4" (8cm)
DEEP
31" (79cm)
6"
(15cm)
R
10x19, 15x24, 12x21
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
36"(92cm) (10x19)
96"(243cm) (15x24)
Trenches for patio blocks
Soil/pool area
10" 10" 10"
(25cm) (25cm) (25cm)
82"(208 cm)
60" (152cm) (12x18)
6"
R
10x16, 12x18
26"
(66cm)
26"
(66cm)
48" (122cm)
48" (122cm)
3-1/4" (8cm)
DEEP
31" (79cm)
(43cm)
17"
(15cm)
36"(92cm) (10x16)
Trenches for patio blocks
Soil/pool area
10" 10" 10"
(25cm) (25cm) (25cm) (25cm) (25cm)
154" (391cm)
60" (152cm) (12-24)
10" 10"
3-1/4" (8cm)
DEEP
26"
31" (79cm)
6"
(66cm)
R
10x22, 12x24
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
(15cm)
36"(92cm) (10x22)
Trenches for patio blocks
Soil/pool area
10" 10" 10"
(25cm) (25cm) (25cm) (25cm) (25cm)
190" (482 cm)
96"(243cm)
10" 10"
3-1/4" (8cm)
DEEP
26"
31" (79cm)
6"
(66cm)
R
15x30
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
(15cm)
(25cm)
10" 26"
(66cm)
Trenches for patio blocks
Soil/pool area
10" 10" 10"
(25cm) (25cm) (25cm) (25cm) (25cm)
190" (482 cm)
132"(335cm)
10" 10"
3-1/4" (8cm)
DEEP
26"
31" (79cm)
6"
(66cm)
R
18x33
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
(15cm)
(25cm)
10" 26"
(66cm)
Trenches for patio blocks
Soil/pool area

Dig a hole 30 cm (12") wide by approximately 25 cm (10") deep in
the center of the circumference.
From the center hole to the projected location of the pool motor, dig
a 15 cm (6") wide trench. Place the removed soil aside to be used
later to cover the hose.
Bottom Drain Assembly
Place teflon tape around the threaded plug. Screw in drain holes
using large pliers. Glue the connector in the appropriate opening.
Take one of the two rubber rings and adjust it to the top of the drain,
aligning the holes carefully. Secure with strips of adhesive tape to
prevent sand from penetrating inside the holes once the drain has
been installed.
Secure one end of the long black or white hose inside the drain
spout. First apply glue on the drain spout and inside the drain end,
then secure with one or two collars.
Cut the hose so that it ends with the stone dust (or sand). Measure
the pool radius from the center of the drain, then add 15 cm (6").
Place the assembled bottom drain in the hole so that it is approxi-
mately 1.3cm (1/2") higher than the surface soil. Bury the hose,
levelling the drain as much as possible. Compact the soil, using
your feet and a tampering tool as well.
Mix three (3) shovels of stone or sand dust with one half shovel of
pure cement, adding a small quantity of water, then pour the cement
around the drain until it reaches 1.3 cm (1/2") from the top.
BOTTOM DRAIN ASSEMBLY (if applicable)
3
1) Refer to Illustration 4.1. To assemble, join splice brackets (R)
to the foot beam (Q) using the bolt 1/2 "X 3" X #13 (12.7 mm x
76.2 mm) (U), nuts (UU ) and washers (V). Remember to insert a
spacer (T) inside the foot beams aligned to each bolt.
STRAIGHT SECTION BUTTRESS ASSEMBLY
4
SPLICE BRACKET (R)
WASHER 1/2” (V)
NUT 1/2” (UU)
FOOT BEAM (Q)
SPACER (T)
BOLT 1/2” X 3” (U)
SPACER
(
T
)
Illustration 4.1

BUTTRESS POST
SPACER (T)
BOLT 1/2” X 3” (U)
NUT 1/2” (UU)
WASHER 1/2” (V)
SPACER (T)
2) Refer to Illustration 4.2. Assemble the buttress post using
bolts 1/2" X 3" X #13 (12,7 mm X 76,2 mm) (U), nuts (UU) and
washers (V). Remember to insert a spacer (T) and two washers
(V) inside the butress post aligned to each bolt.
3) Refer to Illustration 4.3. Cover the bolt heads with bolt cap
covers (W) and insert the styrofoam block (X) at both ends of foot
beam.
STRAIGHT SECTION BUTTRESS ASSEMBLY (continued)
4
1/2” BOLT CAP COVER (W)
STYROFOAM CAP (X)
FOOT BEAM (Q)
STYROFOAM CAP (X)
Illustration 4.3
Illustration 4.2
1) Position the buttress posts assembled in Step 4 on the patio
blocks in the trenches previously dug.
2) Refer to Illustration 5.1 : Once the buttress posts are placed in
the trenches, assemble the straight section bottom tracks between the but-
tress posts by fixing them on the bottom track jonction and fix them to the
foot beams using standard screws #14.
3) Refer to Illustration 5.2 : Fix the pressure plates between the
foot beams with four (4) standard screw ‘’Z’’.
BOTTOM TRACKS (straight section) AND PRESSURE PLATES
5
Illustration 5.1
BOTTOM TRACK
STRAIGHT SECTION
STANDARDSCREW #14
BOTTOM TRACK JONCTION
SCREW
METAL TRACK
RESINE
TRACK
STANDARD
SCREW #14
PRESSURE PLATE
Illustration 5.2

Start with round section, refer to illustration 7.1 :
Place the short end of the bottom track on the last buttress post
from the straight section and secure it with a standard screw # 14
(metal track only). Place the first bottom plate of the round section,
at the other end of the bottom track.
Round section, refer to Illustration 7.2 :
Using the round section bottom tracks and the bottom plates, start
with the first plate of the round section. Repeat this procedure until
the half circle is completed.
Refer to Illustration 7.3. :
Before going to the next step, make sure that the centre of the pool
is properly squared and the metallic tension straps are straight with
no buckles. The two measurements, D1 and D2, should be exactly
the same. If they are not, adjust one entire straight side as neces-
sary. This is a very important step, do not continue until meas-
urements are identical.
SHORT END
BOTTOM TRACK
STRAIGHT SECTION
1STBOTTOM TRACK
ROUNDSECTION
1ST BOTTOM PLATE
ROUNDSECTION
LONGEND
228-248
228-248
230-250
230-250
SCREW
1) Study illustrations and chart carefully. You are now ready to as-
semble the metallic tension straps. Refer to indications on the chart
for the exact number of tension straps per row according to their
respective pool size.
2) Refer to Illustration 6.1: If there is more than one metallic
strap per row, assemble the straps together using 4 bolts and nuts
(BB) 1/4" #20 X 5/8" (6,35 mm X 15,88 mm), taking care of plac-
ing the bolt head on top.
3) Attach the assembled tension straps to the foot beams on both
sides, using four (4) standard screws ‘’Z’’.
TENSION STRAPS ASSEMLBY
6
ROUND SECTION BOTTOM TRACKS ASSEMBLY
7
POOL SIZE 10x16 10x19 10x22 15x30 18x33
345 6 6
ROWSTOASSEMBLE
TENSION STRAPSQUANTITY (TOTAL)
STRAPSPERROW222 2 2
3 4 5 12 18
12x18 12x21 15x24
344
222
688
12x24
5
2
10
Chart
BUTTRESS ASSEMBLY
BOLT 1/4” X 5/8”
NUT 1/4”x 5/8’’
TENSION
STRAPS
SCREWS(Z)
Illustration 6.1
D1
D1
D2
D2
Illustration 7.3
Do not use impact gun to screw the tension straps.
Minimum torque force of 60inch
pounds to maximum of 85 inch pounds.
Illustration 7.1
Resin track 228-248-278
Metal track 230-250-280 Illustration 7.2

WALL INSTALLATION
8
Add sand.
Choose the filter location beside a round section (never in a straight
section). The starting point should be at that location where the
skimmer and return holes are, and as close as possible to the fil-
tration system. When installing the steel wall, it is important to
do so in a location protected from the wind or on a day without
any wind.
Before uncoiling the wall, make sure the pre-punched holes for the
skimmer and pump return are at the top and facing the planned lo-
cation of your filter.
D
ST
SAND
PLANKS
TA
AKESAND
STRINGS
End
BOTTOM PLATE
Begin inserting the wall into the bottom tracks in the middle of a
bottom plate. At first, the wall is kept in place with one or two stakes
and strings (or extra persons). One person uncoils the wall on a
beam or a plank, while a second person inserts it in the bottom
tracks. Do not uncoil more than 3 m (10') of wall before you install
a support bar or stake and string to reinforce the structure.
Once the wall is completely uncoiled, you may find that it is too
long or that both ends do not meet by a few centimetres. If such is
the case, adjust tracks and bottom plates until wall holes line up. If
this does not work, roll up the wall again, check measurements as
per Illustrition 1.1, adjust tracks and plates, if applicable, and uncoil
the wall again. If the spread is too wide, measure the wall and check
it against the chart below.
Join both ends of the wall by orienting folds outward to hide the ex-
clamation icon. (Illustration 8.1)
Note: If the wall is attached properly, you should no longer see
the exclamation icon. If you can always see the icon, you must
reverse the overlap.
Insert bolts and nuts in every hole and tighten with wrench (screw
head on water side of wall). Tape over screw heads with duck tape.
Chart
Illustration 8.1
WARNING : Neveruse an impactgunfor wall screws.
Minimumtorqueforce of 60 inchpoundsto
maximumof 85 inchpounds.
Outsideof pool
Insideof pool
Fold
Fold
BOLT End
Start
NUT
Insideof pool
Outsideof pool
!
IMPORTANT! A non-compliance installation according to manufacturers' instruction will void the warranty.
A faulty installation will cause the wall or joint to split open which could result in serious and/or fatal injuries!
MODELS10x16 18x33
ACTUAL LENGHT
OF THE WALL
10x19 10x22 12x18 12x24 15x24 15x30
43' 8" 49' 8" 55' 9" 49' 81/2" 61' 93/8" 77' 21/2" 86' 71/2"
(13,30m)(15,14m)(17,00m)(15,16m)(18,83m)(19,88m)(23,53m)(26,40m)
65' 21/2"
12x21
55' 93/8"
(17,00m)

You can now spread approximately 4" (10 cm) of compacting sand
all around the inside base of the wall in order to protect the liner
from the sharp edges of the bottom wall tracks and the stone dust
(if applicable), or install a prefabricated cove if available.
SAND BASE FINISHING
Level finishing sand one last time. Make sure that any sharp stones,
debris or roots have been removed from the surface. For better pro-
tection, spray sand with water and pack it once more until the base
is smooth and even.
SAND BASE FINISHING
9
Before pulling the liner up against the wall, insert a vacuum cleaner
hose down into the pump return hole to approximately 15 cm (6")
from the ground.
Maintain the hose in place with adhesive tape. Don't forget to block
the skimmer hole with adhesive tape to prevent air from leaking in.
Place the unfolded liner in the center of the pool area at right angles
with the skimmer hole. Make sure you wear light, flat-soled shoes
to walk on the sand as the slightest heel mark could be visible once
the pool is filled.
Carefully unfold the liner, bringing the bottom-sidewall seam close
to the wall base. Make sure that the side with the protruding seams
faces downward or that the patterned side faces upward.
Lift up a section of the liner over the top of the wall leaving a 10 cm
to 15 cm (4" to 6") fringe outside the wall. Secure the liner with a
plastic coupler (sold separately). Install the top track on the wall
then install the top plates on top of each upright.
At this point, the liner may be too tight, making it difficult to drape
the overlap or, on the contrary, too loose. In such cases, you will
have to redistribute the tension in the liner by removing some of the
couplers and readjusting the liner.
VINYL LINER INSTALLATION
10
30 cm)12" (
LINER
4'' (10 cm)
WALL
SAND COVE
(or PREFAB COVE)
SAND BOTTOM
2'' (5 cm)
PUMP RETURN HOLE
VACUUM CLEANER
INNER WALL
GROUND LEVEL
15 cm (6")
OVERLAP
LINER
RESIN TOP
TRACK
WALL
PLASTIC
COUPLER
(SOLDSEPARATELY)
STEEL
TOP TRACK
PLASTIC
COUPLER
(SOLDSEPARATELY)
228/248/278 230/250/280

VINYL LINER INSTALLATION (continued)
10
Installation detail of a bead liner with top track.
Hang the liner on the top of the wall and install the top track to se-
cure.
Start the vacuum cleaner to allow the liner to adhere to the wall and
check for excess tension at the bottom or for wrinkles. Adjust the
liner by removing wrinkles if needed, lift or lower it in order to ensure
a perfect fit.
Fill the pool with water up to the base of the wall before stopping
and removing the vacuum cleaner.
PUMP RETURN FITTING
After you remove the vacuum cleaner, you may install the return fit-
ting. Place the return fitting ring against the liner and adjust it so
that it is perfectly aligned with the hole in the wall. When the ring is
properly positioned and secured, cut the liner in the middle of the
ring.
Insert the return fitting from the inside, placing the first gasket be-
tween the return fitting and the liner and the second between the
wall and the liner. Then tighten the outside ring with large pliers, tak-
ing care not to crease the liner.
BOTTOM DRAIN (optional)
Find the holes through the middle of the liner and screw the ring
and gasket in against the liner before cutting the liner in the middle
of the ring, then screw on the drain cover.
UPRIGHT POST TOP PLATE (round section)
11
U-BEAD
LINER
RESIN TOP
TRACK
WALL
STEEL
TOP TRACK
Slide the top plate on the upper side of the upright, and secure with
one (1) screw “Z”.
SCREW ‘’Z‘’
228/248/278 230/250/280

UPRIGHT POST INSTALLATION
12
TOP SEAT INSTALLATION
13
Attach the uprights to the bottom plate with two (2) screws “Z”,
which you will find in the hardware bag.
Uprights must be installed outside the flanged part of the bottom
plate and into the two notchs of the bottom track.
Be sure to have a vertical (plumb) upright before fixing the top seat.
Place the top seat on the upper side of the upright.
Center the top seat between the two uprights and secure with four
(4) screws “Z”.
SCREW ‘’Z‘’
‘’Z’’SCREW
BOTTOM
PLATE

SEAT CAP INSTALLATION
14
SECURITY LABELS INSTALLATION
15
The homeowner is responsible to install all safety labels.
SSE Labels (4) :
The safety labels shall be visible from any potential entry points of
the pool. Also, make sure to install safety labels at all access points
of your yard.
PAPTH Label (1) :
The safety label shall be placed at the entrance of the pool, visible
and never covered.
Put the seat cap on the inside section of the seat and interlock with
the upright. Secure the seat cap with one (1) screw “Z”.
Snap the cap logo on top of the upright and secure the bottom with
one (1) screw ‘’Z’’.
Important: if you require additional labels, please contact us at
Trevipools.com

FILTRATION SYSTEM ASSEMBLY
16
PARTS LIST
17
* SEE DRAWING PARTS NEXT PAGE
Assemble skimmer, inlet, drain, filter, pumps, hoses according to separate
manufacturer’s instructions.
Note: See 'Safety Information" Manual.
POOL WALL (finished lenght, inch)
BOLT & NUT FOR 52" (OR 54")WALL
POOL LINER
PLASTICCOUPLER(SOLDSEPARATELY)
TOP SEAT - ROUNDSECTION
TOP SEAT - STRAIGHT SECTION
BOTTOM PLATE
UPRIGHT 52'' or UPRIGHT 54''
TOP PLATE - ROUNDSECTION
SEAT CAP
TOP TRACK - ROUNDSECTION
TOP TRACK - STRAIGHT SECTION
BUTTRESS ASSEMBLY
BUTTRESS POST
TOP PLATE -
STRAIGHT SECTIONS
FOOT BEAM
SPLICE BRACKET
PRESSURE PLATE
SPOOL SLEEVE
BOLT 1/2" X 3" X #13 (12,7 mm X 76,2 mm)
NUT 1/2" (12,7 mm)
WASHER1/2" (12,7 mm)
BOLT CAPCOVER
FOOT BEAM STYROFOAM CAP
TENSION STRAP
1/4" #20 X 5/8" (6,35 mm X 15,88 mm)SCREW & FLANGE NUT
STANDARD SCREW (SCREW #14 ,1" LENGHT)
ITEMDESCRIPTION
AA
BB
CC
DD
A
B
C
D
E
F
G
J
K
L
O
P
Q
R
S
T
U
UU
V
W
X
Y
BB
Z
SEAT CAPEXTENSION - STRAIGHT SECTION
N
TRACK TIE PLATE
M
SOLARCAP
H
BOTTOM TRACK - ROUNDSECTION
BOTTOM TRACK -
STRAIGHT SECTION
NOTE: Please confirm quantities with checklist included in each box.

PARTS LIST
18
BB Z
T
U
UU V
ROUND SECTION STRAIGHT SECTION
Z
Z
C
D
H
J
AA
BB
DD
A
FZ
E
G
Z
CC
K
L
F
Z
P
BB
N
Z
O
TZ
W
UV
R
Q
X
UU
Z
S
M
BB
V
Y

SAFETY AND FUN GO
TOGETHER!
SAFETY INFORMATION
Read this before installing your above-ground pool.
12 775, Brault Street, Mirabel, Quebec, Canada J7J 0C4
Phone: [phone]

The pool is subject to wear and deterioration if not maintained prop-
erly. Certain types of excessive or accelerated deterioration can lead
to failure of the pool’s structure, which may release large quantities
of water that could cause bodily harm, death and property damages.
In order to ensure proper water drainage around the pool, a 2-degree
slope needs to be erected around the perimeter of the pool. THE
MANUFACTURER WILL NOT BE HELD RESPONSIBLE FOR ANY LI-
ABILITY SHOULD THIS STEP BE OMITTED.
Before installing your pool, you should check local regulations such
as building codes, zoning requirements and electrical codes to de-
termine whether a building permit or electricity permit is required to
install your pool. Local regulations may ask you to make sure your
backyard meets set-back requirements, install gates, barriers or
other safety devices, or meet other conditions.
WARNING: All pool components, such as the filtration system,
pump and heater and other objects, should be positioned so that
people cannot use them to gain access to the pool or the deck.
Positioning such objects too close to the pool may allow people
access to the pool while unattended and may cause them serious
injury or death.
We strongly recommend having your pool installed by a professional.
We are not responsible for faulty installation of the pool, we are not
affiliated with any pool installer and assume no responsibility or lia-
bility for the purchaser’s or a professional installer’s errors in in-
stalling your pool. NO DIVING, NO JUMPING and PREVENT
DROWNING stickers are provided with your pool. These stickers
must be affixed to the interior of the pool above the water line, or
any place where the pool users can see them clearly before entering
the pool. If you need more stickers or if some are missing, you can
order these by calling 1 888-777-0447
Although we do not manufacture pool ladders, every pool must have
an ANSI APPROVED pool ladder for proper entering and exiting of
the pool. The proper use of the pool ladder by pool users is an inte-
gral part of general pool safety (Please refer to your pool ladder
safety instructions).
For your protection and for the safety of others, we
recommend that lifesaving equipment be on hand near
the pool at all times.
We recommend that you purchase one of the following:
A light, strong and rigid pole, frequently referred to as a Shepard’s
Crook, at least twelve feet long or a throwing rope at least ¼ inch in
diameter and as long as 1.5 times the maximum width or diameter
of your pool. The rope should be firmly attached to a coast guard-
approved buoy with an outside diameter of approximately 15 inches.
Although we do not manufacture ladders, the proper
use of the ladder by pool users is an integral part of
general pool safety.
NSPI standards require all pools to have an approved
ladder attached for proper access to and from the pool.
The purchaser should follow the pool ladder manufac-
turer’s installation instructions.
Please follow these rules regarding the use of the ladder:
• Only one person on the ladder at a time.
• The user should face the ladder whether going in or out
of the pool.
• NO DIVING or JUMPING from the ladder steps or
the ladder’s platform.
• Check all nuts and bolts regularly to make sure the ladder is safe.
• Inform others of the rules pertaining to the use of ladder and steps.
GENERAL INFORMATION
SAFETY EQUIPMENT
LADDER SAFETY

USAGE SAFETY INFORMATION
1 • Share safety instructions with family, friends, pool watchers or
neighbors.
2 •The installer of the vinyl liner shall affix on the original or re-
placement liner, or on the pool structure, all safety signs in accor-
dance with the manufacturer’s instructions. The safety labels shall
be placed above the water line.
3 • Never dive, jump or slide into an above ground swimming
pool. Diving, jumping or sliding may result in permanent injury or
death. Use a pool ladder or step to enter the pool smoothly, feet
first. The owner must follow the ladder manufacturer’s instruction
and safety warning.
4 • Never swim alone.
5 • Don’t enter the pool if you have been using alcohol or drugs,
because your reaction time may be too slow.
6 • Adult supervision is always necessary. Never take your eyes
off children or swimmers in the water or near the pool, not even
for a minute. Designate an adult “pool watcher”. Make sure that
you or your pool watcher are able to intervene in less then 10
seconds to save a life or avoid injury.
7 • If a child is missing; always look in the pool first.
8 • Be proactive to prevent death or disability.
9 •The pool owner or “pool watcher” should learn CPR (Car-
dioPulmonary Resuscitation) and should teach children and other
people how to swim.
10 • Winter or solar covers are not intended to act as safety bar-
riers. The cover must be completely removed when the pool is in
use. A person may become trapped under a pool cover, which
may result in severe bodily injuries, including death.
11 •Keep rescue equipment such as life rings and reaching
poles etc, by the pool. Please consult you municipality to get a
rescue equipment list.
12 • An emergency phone number such as: nearest available
police, fire, ambulance and/or rescue unit, must be visible from
pool area. A functioning and/or cellular phone must be reachable
within 10 seconds.
13 • Avoid entrapments. Suction from a pool drain or skimmer
can trap an adult or children underwater:
• Hair can get caught in faulty drain cover.
• Arms, legs and fingers can become lodged in a suction open-
ing.
• Any body part that can cover a drain can cause injuries.
• Jewelry or bathing suits can become entangled in a faulty drain
cove.
A pool with broken, loose, missing or non compliant drain cover
should be considered as dangerous and should not be used.
14 •Lighting, when installed, shall be in concordance with the
National Electrical Code.
15 • During nighttime pool use, artificial lighting must be used to
illuminate pool, all safety signs, ladders, steps, deck surface and
walkways.
16 • All electrical appliances must be kept away from the pool,
and not be reachable by pool users.
17 • The pool deck should be kept clean and clear of objects to
avoid tripping or slipping. The deck should have a non-slip sur-
face.
18 • Do not sit, dive, climb or stand on the top rails of the pool.
19 • It is important that all users be able to see the bottom of the
pool. Foggy water must be cleared up before entering the pool.
20 • Steps and pool ladders should be secured and locked or re-
moved when the pool is not in use. Swimming pool barriers or
fences with self-latching and self-closing gates which prohibit
children or other people from gaining access to the pool must be
installed around the pool to avoid injury or death. The latch should
be out of reach of children. Consult your municipality for more
details and specifications.
Amended 03/06/2022

Choisissez l'emplacement idéal pour votre piscine en tenant
compte des lois municipales sur la distance des clôtures, celles
des services publics sur la distance des fils électriques, ainsi
que l'aménagement paysager prévu après l'installation.
1) Plantez un pieu aux points A et B en respectant la distance de la
section centrale entre ces deux points (A-B). Il est important que
vos mesures A et B soient exactes au tableau 1.1 pour assurer une
installation correcte et éviter des problèmes ultérieurs.
2) Tracez deux demi-cercles selon le bon rayon (R).
3) Joignez les deux demi-cercles par des lignes droites en s’assur-
ant de respecter la largeur entre ces deux lignes (D).
4) Vérifiez que la longueur totale soit conforme (E)
5) Ajoutez ensuite sur chaque côté des tranchées d’une largeur de
15cm (6”) et d’une longueur correspondante (F).
6) Enlevez la pelouse sur toute la surface délimitée.
E
F
A-B
R
R
MUR DE LA PISCINE
(ligne pointillé)
LIMITE DE DÉTERREMENT
ENLÈVEMENT
DU GAZON
D
15 cm (6”)
15 cm (6”)
Cher(e) client(e),
Félicitations, vous avez fait l'acquisition d'une piscine d'une qualité et d'une durabilité supérieures. Suivez
les instructions attentivement pour obtenir les meilleurs résultats possibles. Toute dérogation à la marche à suivre
peut occasionner des dommages à votre piscine ou à votre propriété et annuler votre garantie. Nous vous suggérons
de lire attentivement les instructions au préalable afin de vous familiariser avec les différentes pièces de votre piscine.
Assurez-vous de bien comprendre toutes les étapes avant de commencer l'assemblage.
Nous vous souhaitons un été des plus agréable et rafraîchissant.
Nous recommandons fortement de faire installer votre piscine par un professionnel.
AVERTISSEMENT : Assurez-vous d’avoir lu le manuel “ Information de sécurité ”
avant de commencer l’installation de votre piscine.
AVERTISSEMENT : Votre piscine n'est pas conçue pour le plongeon et/ou les sauts tête
première. Pour votre sécurité, abstenez-vous de plonger car ceci pourrait causer de graves
lésions ou entraîner la mort.
INSTRUCTIONS D’ASSEMBLAGE
PISCINES OVALES NBS
Trevi 228/230/248/250/278/280
PRÉPARATION DE L’EMPLACEMENT
1
Figure 1.1
Tableau 1.1 - Zones de déterrement (Figure 1.1)
1,67m (5' 6")
1,67m (5' 6")
3,35m (11')
3,35m (11')
6,09m (20' 0")
7,01m (23' 0")
2,99m (9' 10")
3,91m (12' 10")
NOM DU MODÈLE
DISTANCE (A-B) RAYON (R) LARGEUR (D) LONGUEUR TOTALE (E) TRANCHÉE (F)
10'x19'2,75m (9' 0")
10'x22'3,65m (12' 0")
1,67m (5' 6")3,35m (11')5,18m (17' 0")2,08m (6' 10")
10'x16'1,82m (6' 0")
2,43m (8' )
2,89m (9' 6")
4,87m (16')
5,79m (19')
9,44m(31' 0")
10.36m (34' 0")
4,82m (15' 10")
4,82m (15' 10")
15'x30' 4,57m (15' 0")
18'x33'4,57m (15' 0")
1,98m (6' 6")
2,43m (8' )
3,96m (13')
4,87m (16')7,62m (25' 0")
3,91m (12' 10")
2,99m (9' 10")
12'x24' 3,65m (12' 0")
15'x24' 2,75m (9' 0")
1,98m (6' 6")3,96m (13')5,79m (19' 0")2,08m (6' 10")
12'x18'1,82m (6' 0")
7,62m (25' 0")
1,98m (6' 6")3,96m (13')6,70m(22' 0") 2,99m (9' 10")
12'x21'2,75m (9' 0")
40305_V7_2022-05-27
NBS

NIVELLEMENT DU TERRAIN
Pour une installation de piscine ovale on doit absolument faire un fond
plat. Nivelez la surface très attentivement en utilisant un niveau de
menuisier et une planche très droite. Éliminez toutes les petites
buttes de terre. Assurez-vous d'avoir un terrain exempt de tous
débris tels que pierres, bois, etc.
TRANCHÉES POUR L’EMPLACEMENT DES ÉQUERRES
(COULOIRS)
1) Creusez des couloirs pour atteindre une profondeur égale à la
somme de l’épaisseur des dalles de ciment (dalles de 2” recom-
mandées) et de l’épaisseur des équerres 8cm (3 1/4”). (Se référer
aux illustrations pour le dessin des couloirs).
2) S’assurez que ces couloirs soient plats et de niveau sans les
compacter.
3) Disposez les dalles de ciment dans les tranchées en s’assurant
qu’elles soient de niveau et que le dessus des dalles arrive à 8cm
(3 1/4”) de profondeur. Une fois que les équerres y sont déposées,
le dessus des équerres doit être de niveau avec la surface du sol
prévue pour la piscine.
NIVELLEMENT DU TERRAIN ET EXCAVATION
2
Tableau: Quantités de sable
3,05 mx 6,70 m(10’ x 22’)2Tonnes 1 Tonne
3,05 mx 5,79 m(10’ x 19’)2Tonnes 1 Tonne
3,05 mx 4,87 m(10’ x 16’)2Tonnes 1 Tonne
3,66 mx 6,40m(12’ x 21’)2Tonnes 1 Tonne
3,66 mx 5,48m(12’ x 18’)2Tonnes 1 Tonne
10" 10" 10"
(25cm) (25cm) (25cm) (25cm)
118" (299 cm)
48" (121cm) (12x21)
10"
3-1/4" (8cm)
Profondeur
31" (79cm)
6"
(15cm)
R
10x19, 15x24, 12x21
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
36"(92cm) (10x19)
96"(243cm) (15x24)
Tranchées pour dalles de ciment
Surface du sol
10" 10" 10"
(25cm) (25cm) (25cm)
82"(208 cm)
60" (152cm) (12x18)
6"
R
10x16, 12x18
26"
(66cm)
26"
(66cm)
48" (122cm)
48" (122cm)
3-1/4" (8cm)
Profondeur
31" (79cm)
(43cm)
17"
(15cm)
36"(92cm) (10x16)
Tranchées pour dalles de ciment
Surface du sol
10" 10" 10"
(25cm) (25cm) (25cm) (25cm) (25cm)
154" (391cm)
60" (152cm) (12-24)
10" 10"
3-1/4" (8cm)
Profondeur
26"
31" (79cm)
6"
(66cm)
R
10x22, 12x24
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
(15cm)
36"(92cm) (10x22)
Tranchées pour dalles de ciment
Surface du sol
10" 10" 10"
(25cm) (25cm) (25cm) (25cm) (25cm)
190" (482 cm)
96"(243cm)
10" 10"
3-1/4" (8cm)
Profondeur
26"
31" (79cm)
6"
(66cm)
R
15x30
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
(15cm)
(25cm)
10" 26"
(66cm)
Tranchées pour dalles de ciment
Surface du sol
10" 10" 10"
(25cm) (25cm) (25cm) (25cm) (25cm)
190" (482 cm)
132"(335cm)
10" 10"
3-1/4" (8cm)
Profondeur
26"
31" (79cm)
6"
(66cm)
R
18x33
26"
(66cm)
26"
(66cm)
26"
(66cm)
(43cm)
17"
48" (122cm)
48" (122cm)
(15cm)
(25cm)
10" 26"
(66cm)
Tranchées pour dalles de ciment
Surface du sol

Creusez un trou de 30 cm (12") de largeur par environ 25 cm (10")
de profondeur en plein centre de la circonférence.
Creusez une tranchée d'environ 15 cm (6") de largeur à partir du
trou central jusqu'à l'emplacement du moteur de la piscine. La terre
retirée sera déposée à côté de la tranchée car elle servira à enterrer
le tuyau.
Assemblage du drain
Placez du téflon autour du bouchon fileté et vissez-le dans le trou
du drain. Collez le raccord dans l'ouverture prévue à cet effet.
Prenez une des rondelles de caoutchouc et ajustez-la sur le dessus
du drain en prenant bien soin d'aligner les trous. Fixez-la ensuite
avec des lanières de ruban adhésif afin d'éviter que le sable ne
pénètre dans les trous une fois le drain installé.
Fixez une des extrémités du long tuyau noir ou blanc dans l'embout
du drain, en prenant soin au préalable d'appliquer de la colle sur
l'embout du drain et à l'intérieur de l'extrémité du tuyau. Et, surtout,
entourez-le d'un ou deux collets.
Coupez le tuyau de façon à ce qu'il se termine avec la fin de la pous-
sière de roche ou de sable. On calcule le rayon de la piscine plus
15 cm (6") à partir du centre du drain.
Placez le drain de fond assemblé dans le trou de façon à ce qu'il
soit environ 1,3 cm (1/2") plus haut que la terre de surface. Enterrez
le tuyau en plaçant le drain le plus possible de niveau. Compactez
avec les pieds et le pilon.
Mélangez trois pelletées de poussière de roche ou de sable avec
une demi-pelletée de ciment pur et un peu d'eau et coulez ce ciment
autour du drain jusqu'à 1,3 cm (1/2") sous le dessus du drain.
INSTALLATION DU DRAIN DE FOND (optionnel)
3
1) Se reférer à l’illustration 4.1. Pour assembler, fixez les équerres
(R) à l’omega de base (foot beam) (Q) à l'aide du boulon 1/2" X 3" X
#13 (12,7 mm X 76,2 mm) (U) des écrous (UU) et des rondelles
(V). N’oubliez pas d’insérer un tube d’espacement (T) à l’intérieur
des omégas vis-à-vis chaque boulon.
ASSEMBLAGE DES POTEAUX DE RENFORT SECTION DROITE
4
ÉQUERRE (R)
RONDELLE 1/2” (V)
ÉCROU 1/2” (UU)
OMÉGA DE BASE (Q)
TUBE D’ESPACEMENT (T)
BOULON 1/2” X 3” (U)
TUBE D’ESPACEMENT
(
T
)
Illustration 4.1

POTEAU DE RENFORT
BOULON 1/2” X 3” (U)
RONDELLE 1/2” (V)
ÉCROU 1
/
2”
(
UU
)
TUBE D’ESPACEMENT (T)
TUBE D’ESPACEMENT (T)
2) Se reférer à l’illustration 4.2. Fixez les poteaux de renfort à l'aide
du boulon 1/2" X 3" X #13 (12,7 mm X 76,2 mm) (U) des écrous
(UU) et des rondelles (V). N’oubliez pas d’insérer un tube d’espace-
ment (T) ainsi que deux rondelles (V) à l’intérieur des poteaux de
renfort vis-à-vis chaque boulon.
3) Se reférer à l’illustration 4.3. Recouvrir les têtes de boulon avec
les capuchons pour boulons (W) et insérer les embouts de mousse
(X) aux deux extrémités des omégas de base (foot beam).
ASSEMBLAGE DES POTEAUX DE RENFORT (suite)
4
CAPUCHON POUR BOULON 1/2” (W)
EMBOUT DE MOUSSE (X)
OMÉGA DE BASE (Q)
EMBOUT DE MOUSSE (X)
Illustration 4.3
Illustration 4.2
1) Positionnez les poteaux de renfort assemblés de l’étape 4 sur
les dalles dans les tranchées préalablement creusées.
2) Se reférer à l’illustration 5.1 : une fois les poteaux de renfort
disposés dans les tranchées, insérez l’attache de rainure dans les rain-
ures de la section droite entre les poteaux de renfort et fixez-les sur
les omégas de base (foot beam) à l’aide de vis standards ‘’Z’’.
3) Se reférer à l’illustration 5.2 : fixez les plaques de pression
entre les omégas de base (foot beam) à l’aide de quatre (4) vis
standards ‘’Z’’.
RAINURES SECTION DROITE ET PLAQUES DE PRESSION
5
Illustration 5.1
RAINURE DU BAS
SECTION DROITE
VISSTANDARD #14
ATTACHE DE RAINURE
VIS
RAINURE
DE MÉTAL
RAINURE
DE RÉSINE
VISSTANDARD #14
PLAQUE DE PRESSION
Illustration 5.2

1ERERAINURE DU BAS
SECTION RONDE
1EREPLAQUE DU BAS
SECTION RONDE
BOUT
COURT
RAINURE DU BAS
SECTION DROITE
BOUT LONG
228-248
230-250
VIS
228-248
230-250
1) Consultez les illustrations et le tableau et étudiez-les attentive-
ment. Vous pouvez maintenant assembler les bandes de tension
métalliques. Référez-vous aux indications du tableau pour le nombre
de rangées de bandes métalliques à assembler et le nombre de ban-
des par rangée en fonction des dimensions de piscine.
2) Se reférer à l’illustration 6.1: S’il y a plusieurs bandes par
section, assemblez les bandes de tension ensemble avec 4 boulons
et écrous (BB) 1/4" #20 X 5/8" (6,35 mm X 15,88 mm), en prenant
soin de placer la tête du boulon sur le dessus.
3) Fixez les bandes de tension ainsi assemblées aux omégas de
base (foot beam) des deux côtés, à l'aide de quatre (4) vis stan-
dards ‘‘Z’’.
ASSEMBLAGE DES BANDES DE TENSION
6
Début de la section ronde, se reférer à l’illustration 7.1 :
Placez le bout court de la rainure sur le dernier poteau de renfort
de la section droite et fixez-la à l’aide d’une vis standard ‘’Z’’(rainure
de métal seulement). À l’autre bout de la rainure, placez la première
plaque du bas de la section ronde.
Section ronde, se reférer à l’illustration 7.2 :
Prenez les rainures du bas et les plaques du bas et commencez par
la première plaque de la section ronde. Répétez jusqu'à ce que le
"demi-cercle" soit complété.
Se reférer à l’illustration 7.3. Avant de procéder à l’étape suivante,
assurez-vous que le centre de votre piscine soit au trait carré et que
les bandes de métal soient bien tendues. Les deux mesures, D1 et
D2, doivent être identique. C'est une étape très importante, ne
continuez pas tant que les mesures ne sont pas identiques.
ASSEMBLAGE DES RAINURES DES SECTIONS RONDES
7
Tableau
POTEAUX DE RENFORT
ASSEMBLÉS
BOULON 1/4” X 5/8”
ÉCROU 1/4”x 5/8’’
BANDESDE TENSION
VIS(Z)
Illustration 6.1
D1
D1
D2
D2
Illustration 7.3
Illustration 7.1
Rainures résine 228-248-278
Rainure métal 230-250-280 Illustration 7.2
MODÈLE 10x16 10x19 10x22 15x30 18x33
345 6 6
NOMBRE DE RANGÉESÀ ASSEMBLER
NOMBRE DE BANDESTOTAL
NOMBRE DE BANDESPARRANGÉE 222 2 2
3 4 5 12 18
12x18 12x24 15x24
354
222
6108
12x21
4
2
8
Ne pas utiliser de pistolet à chocs (impact gun)
pour visser les bandes de tension.
Serrage minimum de 60livres pouce
et maximum de 85 livres pouce.