Tripp Lite 108 User manual

Smart CAT5 Switch - 108
and 116
Quick Start Guide
1. Introduction
To take advantage of the full range of features, we recommend you read the softcopy
User Guide after performing the Quick Start procedure. It’s in PDF format on the
supplied CD or on our website www.minicom.com in the S
upport section.
Access and control multiple multi-
platform computers from one Keyboard Video
Mouse (KVM) console with the Smart CAT5 Switch (Smart CAT5) system. The Smart
CAT5 comes in 108 and 116 models. Connect up to 8 computers to the 108 model, and
up to 16 to the 116 model.
2. System components
The Smart CAT5 system consists of:
Smart CAT5 Switch 108 or 116
RICC on Cable (ROCS) - PS/2, USB
CAT5 cables (1.5m provided)
RS232 Serial cable
Rack mounts for the Smart CAT5
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright
©2012 Tripp Lite. All rights reserved.
and 116
To take advantage of the full range of features, we recommend you read the softcopy
User Guide after performing the Quick Start procedure. It’s in PDF format on the
upport section.
platform computers from one Keyboard Video
Mouse (KVM) console with the Smart CAT5 Switch (Smart CAT5) system. The Smart
CAT5 comes in 108 and 116 models. Connect up to 8 computers to the 108 model, and
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
©2012 Tripp Lite. All rights reserved.

SMART CAT5 SWITCH – 108/116
1
3. The Smart CAT5 system configuration
Figure 1 illustrates the basic configuration of the Smart CAT5 system.
Figure 1 Smart CAT5 system configuration
4. The Smart CAT5 models
The figure below illustrates the rear panel of the Smart CAT5 116. The 108 model is
the same but with only 8 Computer ports.
Figure 2 Smart CAT5 116 rear panel
5. Pre-installation guidelines
Switch off all computers
Place cables away from fluorescent lights, air conditioners, and machines that are
likely to generate electrical noise
Ensure that the maximum distance between each computer and the Smart CAT5,
does not exceed 10m/33ft
Workstation
To servers
MINICOM
POWER
100-240 VAC 50/60 Hz 12345678
10 11 12 13 14 15 169 COMPUTER
www.minicom.com
SMART CAT5 SWITCH 116
RoC/RICCs
to servers
POWER
100-240 VAC 50/60 Hz 12345678
10 11 12 13 14 15 169 COMPUTER
www.minicom.com

QUICK START GUIDE
2
6. Connecting the Smart CAT5 system
Each computer / server is directly connected to the Smart CAT5 via the appropriate
ROC using CAT5 cable in a star configuration. No external power is needed at the
remote ROCs. The ROCs draw their power from the computer’s keyboard port (ROC
PS/2) or from the USB port (ROC USB). The figures below illustrate the ROC PS/2
and ROC USB.
Figure 3 ROC PS/2 Figure 4 ROC USB
Connecting the KVM console
Connect a KVM console to the Smart CAT5 as illustrated in Figure 1 above.
Connecting a ROC to each computer
Connect the ROCs as detailed in the figures above.
Connecting the CAT5 cables
1. Connect one connector to the ROC’s RJ45 port.
2. Connect the other connector to one of the Smart CAT5’s Computer ports.
3. Follow the above 2 steps for each computer.
7. Connecting the power supply
1. Connect the Smart CAT5 to the power supply using the Power cable provided. Use
only power cord supplied with the unit.
2. Switch on the computers.
8. Operating the Smart CAT5 system
Below is a brief outline of how to switch between computers. See the softcopy User
Guide for the full operating details.
To computer’s
keyboard port
To computer’s
mouse port
To computer’s
Video card
To computer’s
USB Port
To computer’s
Video Card

SMART CAT5 SWITCH – 108/116
3
Switch between the connected computers by either
The front panel Select buttons
Keyboard hotkeys - To switch to the next computer forwards press Shift then,
+. Release Shift, before pressing +. To switch to the next computer backwards
press Shift then, -. Release Shift, before pressing -.
Control software (See softcopy User Guide)
The OSD
The OSD is also the place to adjust various settings as explained in the softcopy User
Guide.
When switching computers the illuminated LED of the top row indicates which
computer is currently selected.
9. The OSD
To display the OSD:
Press Shift twice. The OSD Main window appears.
Navigating the OSD
To navigate up and down use the Up and Down arrow keys.
To exit the OSD press Esc.
10. Selecting a computer
To select a computer:
1. Navigate to the desired computer line.
Or, type the port number of the desired computer.
2. Press Enter. The selected computer is accessed. An OSD label appears showing
which computer is accessed.
Note! When the OSD is displayed you cannot select computers using the front panel
Select buttons or the keyboard hotkeys.
11. Resetting the switch
To reset the switch press the 2 front panel Select buttons simultaneously. The ROCs
are unaffected by this reset.
For the rest of the configuration and operating instructions please see the softcopy User
Guide on the supplied CD or on our website
http://www.minicom.com/supportuserguides.htm
201204197 • 933194_EN