Triton Tyne User manual

2180417B October 2005
INSTALLERS PLEASE NOTE THESE INSTRUCTIONS ARE TO BE LEFT WITH THE USER
Installation
Instructions
TYNE
Monobasin tap

Monobasin tap
2
INTRODUCTION
This guide contains all the neccessary fitting
instructions for your Unichrome monobasin tap.
Note: This basin tap is suitable for use with
single holed style basins only.
Please read this guide carefully before beginning
your installation.
The tap installation must be carried out by a
suitably competent person and in the sequence
of the instruction book.
Care taken during the installation will ensure
long life and trouble free operation from your
tap.
DO NOT choose a position where the tap
could become frozen.
Replacement parts can be ordered from Triton
Customer Service (see back page).
WATER PRESSURE
This tap is suitable for all water pressures and
should be fitted in accordance with Water
Regulations.
Pressure range - 0.1 bar to 10 bar
COMPONENTS
The tap set comprises of the following:
1 Monobasin tap
2 Silicon seal
3 Silicon seal
4 Horseshoe plate
5 Stud
6 Retaining nut
- Steel braided hoses (2 off)
7 Plunger control rod
8 Fixing block
9 Plunger
10 Upper waste outlet
11 Upper silicon seal
12 Lower silicon seal
13 Lower waste outlet
14 Control lever
Check that all parts are correct (fig.1).
1
2
3
4
5
8
6
14
7
9
10
11
12
13
Fig.1

3
Monobasin tap
INSTALLATION
DO NOT use jointing compounds on any
pipe fittings for the installation.
Fitting the tap
Screw the stud into the hole in the base of the
tapunit and secure. Fit the steel braided hoses
into the hot and cold inlets (fig.2) and tighten
to secure.
Seat the silicon seal into the recess in the base
of the basin. Feed the braided hoses through
the collar and opening in the basin and place
the tapassembly in place. Make sure the tapand
silicon seal sit correctly on the basin.
Slide the remaining silicon seal and horseshoe
plate over the stud and secure the tap assembly
in place using the nut provided (fig.3).
Note: DO NOT overtighten the nut as this
may damage the tapunit and basin.
Fitting the waste unit
Take the waste assembly apart, as shown in
(fig.4).
Insert the control lever through the opening
in the side of the lower waste outlet. Fit the
retaining nut and tighten. Finger tight should
be sufficient.
Slide the silicon seal onto the upper waste outlet
and fit the lower silicon seal onto the lip on
the lower waste outlet (fig.5). Place the upper
waste fitting into the drainage hole in the basin.
Screw the lower waste outlet into the upper
waste outlet - DO NOT tighten at this stage.
Align the lower fitting such that the control arm
faces towards the rear of the basin and secure.
Slide the top half of the plunger control rod
through the opening in the rear of the tapunit.
From the underside of the basin, screw the
lower section of the control rod into the top rod
and tighten.
Push the control lever down and then slide the
Upper waste outlet Lower silicon seal
Upper silicon seal Lower waste outlet
Retaining nut
WARNING!
The tap must not be positioned
where it will be subject to freezing
conditions.
Fig.4
Stud
Braided
hoses
Fig.2
Tap
Silicon seal
Basin
Silicon seal
Horseshoe
plate
Stud
Nut
Fig.3

Monobasin tap
4
fixing block onto the control lever. The fixing
block is designed to move along the lever to
allow for correct positioning (Fig.6).
Slide the fixing block so that the control rod can
fit through the block (Fig.7). Tighten the screw
to secure the plunger control rod.
Place the plunger in the waste assembly. To alter
the plunger gap, remove the plunger and adjust
the screw in the plunger base (Fig.8).
FINISHING THE INSTALLATION
IMPORTANT: Before completing the
connection of the water supply to the inlets
of the mixer, flush out the system to remove
any debris in the pipework. This can be done
by connecting a hose to the pipework and
turning on the mains water supply long
enough to clear the debris to waste.
Connect the steel braided hoses to the hot
and cold supplies using standard ½” BSP tap
connectors.
Connect the waste outlet to standard 1¼” waste
trap.
Slide the control rod
into the fixing block
and secure
Fixing block
Control lever
Control rod
Fig.7
Fixing
block
Control
lever
Control rod
Slide fixing block
into position
Fig.6
Basin
Upper waste
outlet
Lower waste
outlet
Lower silicon seal
Upper silicon
seal
Control
lever
Nut
Fig.5

5
Monobasin tap
OPERATION
The tap has handwheel controls for both hot
and cold.
To close the waste gate pull the control rod at
the rear of the unit upwards (Fig.9). This will
drop the plunger into the outlet. To open the
waste gate push the rod down.
CLEANING
IMPORTANT: DO NOT use abrasive or solvent
cleaning fluids. The tapunit should be cleaned
using a soft cloth and warm water. Any stains
should be removed using washing up liquid.
SPARE PARTS
Description Part No.
¼ turn ceramic valve (½”) 83308060
Handwheel 83308230
Complete anti-splash tap 83308070
Adjust the
screw length to
alter the gap
Fig.8
Pull rod to
operate
waste gate
Fig.9

Monobasin tap
6
Monobasin mixer

7
Monobasin tap

Replacement Parts Policy
Availability: It is the policy of Triton to
maintain availability of parts for the current
range of products for supply after the
guarantee has expired. Stocks of spare
parts will be maintained for the duration of
the product’s manufacture and for a period
of five years thereafter.
In the event of a spare part not being
available a substitute part will be supplied.
Payment: The following payment methods
can be used to obtain spare parts:
1 By post, pre-payment of pro forma
invoice by cheque or money order.
2 By telephone, quoting credit card
(MasterCard or Visa) details.
3 By website order:
www.tritonshowers.co.uk
Triton Plc, Triton Road,
Nuneaton, Warwickshire. CV11 4NR
Triton Plc guarantee this product against
all mechanical defects arising from faulty
workmanship or materials for a period
of five years for domestic use only, from
the date of purchase, provided that it has
been installed by a competent person in
full accordance with the installation and
operating instructions.
Any part found to be defective during this
guarantee period we undertake to repair
or replace at our option without charge so
long as it has been properly maintained
and operated in accordance with the
operating instructions, and has not been
subject to misuse or damage.
This product must not be taken apart,
modified or repaired except by a person
authorised by Triton Plc. This guarantee
applies only to products installed within
the United Kingdom and does not apply to
products used commercially.
This guarantee does not affect your
statutory rights.
What is not covered:
1 Breakdown due to: a) use other than
domestic use by you or your resident
family; b) wilful act or neglect; c) any
malfunction resulting from the incorrect
use or quality of gas or water or incorrect
setting of controls; d) faulty installation.
2 Repair costs for damage caused by
foreign objects or substances.
3 Total loss of the product due to non-
availability of parts.
4 Compensation for loss of use of the
product or consequential loss of any kind.
5 Call out charges where no fault has
been found with the unit.
6 The cost of routine maintenance,
adjustments, overhaul modifications or loss
or damage arising therefrom, including
the cost of repairing damage, breakdown,
malfunction caused by corrosion, furring,
pipe scaling, limescale, system debris or
frost.
TRITON STANDARD GUARANTEE
Customer Service
☎ [phone]
Scottish and Northern Ireland
Customer Service
☎ [phone]
Trade Installer Hotline
☎ [phone]
Fax: [phone]
www.tritonshowers.co.uk
E mail: [email protected]
To use your Triton Guarantee please
contact Triton Customer Service on
[phone] (Scotland
[phone]). Please have
your postcode and model details available
when you call.
Please note: Telephone calls may be
recorded for training purposes.