Trojan DELTA 300 Installation guide

www.trojanhealth.co.za
#1
HOME
FITNESS
SOUTH AFRICA’S
SINCE
1981
0861 876526
0861 TROJAN
WARRANTY
TROJAN
MY SPACE MY TIME
®
CAUTION
READ ALL PRECAUTIONS AND
INSTRUCTIONS IN THIS MANUAL
BEFORE USING THIS EQUIPMENT.
KEEP THIS MANUAL FOR
FUTURE REFERENCE

10213-3

10213-4

10213-5

10213-6
PARTS NO. DESCRIPTION Q’TY
1 Frame 1
2 Seat Rail 1
9 Front Stabiliser 1
10 Foot Pedals 2
12 Rear Support Post 1
18 Support Bracket 1
32/33 Foot Pedal With Velcro Strap 2
36 Foot Pedal Rod 1
37 Foot Pedal Support Pivot
Shaft
1
55 Computer 1
89/91 Seat with Carriage Bracket 1
90 Seat Rail Cap 2

10213-7
PART DESCRIPTION Q’TY
26 Allen Head Bolt M8 x 55mm 2
25 Spring Washer M8 9
24 Flat Washer M 8 7
11 Lock Pin 2
31 Flat Washer M 8 2
38 Allen Head Bolt M8 x 15mm 7
42 Acorn Nut M10 1
45 Flat Washer Ø20 x Ø10.2 x 2t 1
47 Allen Head Bolt M10 x130mm 1
48 Sphere Head Locking Pin 1
80 Flat Head Bolt M8 x 85mm 1
81 Stopper 2
82 Nut M8 1
96 Universal Wrench 13.17 1
97 Allen Wrench 6mm 2

10213-8
Note:The hole in the inner tube has one pre-assembled Spring Clip
(99) which will stop the Support Rod (37) moving.

10213-9
CAUTION:
Ensure that cables are not damaged
during assembly or when tightening screws.

10213-10
Recheck
all bolts and nuts are
tightened securely
before using the machine

10213-11

10213-12
EXERCISE COMPUTER FUNCTION/SPECIFICATIONS
CALORIES 0.0-999.9 KCAL (THEORETICAL)
DISTANCE 0.0-999.9 KILOMETRES
COUNTER 0~9999 (TOTAL STROKES)
SPEED 0.0-999.9 KM/H (CURRENT ROWING SPEED)
TIMER 0.00-99.59 MINUTES (COUNT UP)
EXERCISE MONITOR OPERATING SPECIFICATIONS
POWER SOURCE 2 x AA(1.5V) POWER CELLS
STORAGE TEMPERATURE -10c-+60c
NORMAL OPE RATING TEMPERATURE 0c-+40c
USING THE EXERCISE MONITOR ON YOUR ROWER
The Computer has functions with a 3 split LCD display screen.When the computer detects a signal input, the computer will display
the function TIME, DISTANCE, CALORIES in order.
The computer will be turned on automatically by pressing the MODE button or when you start rowing.
The computer will shut off automatically if no signal is detected for 4 minutes.You can press MODE button or start rowing to
continue computer operation.
BATTERY INSTALLATION
To fit the BATTERIES to the Monitor, please remove the BATTERY COVER at the REAR of the monitor. Carefully fit the batteries
supplied (and any subsequent new batteries) between the exposed contacts. Please ensure that the batteries are fitted
with the ‘+’/ ‘-’ends matching the outline on the sticker in the battery compartment. Failure to fit the batteries correctly may result
in damage to the Monitor, which is not covered by our guarantee. Dispose of old batteries responsibly.

10213-13

10213-14

10213-15
1
2
3
4
5

10213-16
controlled

10213-17
TROUBLE SHOOTING
PROBLEM CAUSE CORRECTION
Monitor does not display Adaptor not plugged in or batteries not
installed
Plug adaptor in or insert batteries
No speed or distance displays on
the monitor
Sending unit not connected Securely plug sending unit into
extension wire at the back of the computer
Sending unit not working properly Replace sending unit
Computer not working properly Replace computer
No tension Motor cable or resistance cable not
connected
Securely connect the motor cable into the
extension motor cable and the resistance cable
Magnetic wheel not working properly Replace magnetic wheel
Grinding Crank bearing defective Replace crank bearings
Idle pulley defective Replace idle pulley
Mag. flywheel defective Replace mag. flywheel
Squealing Poly V-belt s lipping Adjust po ly V-belt

10213-18

10213-19
PA RT. DESCRIPTION Q’TY
24 Flat Washer M 8 11
25 Spring Washer M8 10
26 Allen Head Bolt M8 x 55mm 2
27 Resistant System With Tension Strap 1
28l/R Chain Guard 1P
29 Crank Cover 2
30 Bushing Ø10.5x Ø8.2 x 28.2mm 2
31 Flat Washer M 8 2
32 Foot Pedal 2
33l/R Pedal Strap 1P
34 Machine Screw M5 x 15mm 4
35 Machine Screw M5 x 10mm 6
36 Pivot Shaft 1
37 Support Rod 1
38 Allen Head Bolt M8 x 15mm 8
39 Sensor Wire Pad 4
40 Machine Screw M4 x 10mm 4
41 Plug 1
42 Acorn Nut M10 1
43 Flat Washer Ø20 x Ø10.2 x 2.5t 1
44 Anti-Slippery Pad 2
45 Flat Washer Ø20 x Ø10.2 x 2t 1
46 Bushing 2
PA RT. DESCRIPTION Q’TY
1 Main Frame 1
2 Seat Rail 1
3 Handlebar 1
4 Foam Grip 2
5 Handlebar Sleeve 1
6 Cap 2
7 Computer Bracket 1
8 Handlebar Holder 1
9 Front Stabiliser 1
10 Foot Plate 2
11 Lock Pin 2
12 Support Post 1
13 Support Bracket 1
14 Reinforce Bracket A 1
15 Reinforce Bracket B 1
16 Hex Nut M16 2
17 Sensor Bracket 1
18 Support Bracket 1
19 Anti-Slippery Sticker 2
20l/R Transportation Wheel C ap 1P
21 Anti-Slippery Pad 2
22 Flat Washer M 6 2
23 Machine Screw M5 x 12mm 2

10213-20
PA RT. DESCRIPTION Q’TY
47 Allen Head Bolt M10 x 130mm 1
48 Sphere Head Locking Pin 1
49 Plug 1
50 Small Plug 1
51 Middle Section Speed Up Sensor Wire A 1
52 Speed Up Sensor 1
53 Count Sensor 1
54 Middle Section Count Sensor Wire 1
55 Computer 1
56 Screw M5 x 12mm 4
57 Allen Head Bolt M8 x 60mm 1
58 Allen Head Bolt M8 x 68mm 1
59 Flat Washer Ø22 x Ø8.4 x 3.0t 2
60 Acorn Nut M8 2
61 Guide Wheel 2
62 Bearing 4
63 Magnet 1
64 Tension Knob 1
65 Cross Head Screw M5 x 20mm 1
66 Magnetic Flywheel System 1set
67 Allen Head Bolt M10 x 40mM 1
68 Allen Head Bolt M8 x 20mm 1
69 Idle Wheel Bracket 1
70 Bushing 1
71 Idle Wheel 1
72 Nylon Nut M10 x 7mm 1
73 Nylon Nut M8 7
74 Flat Washer Ø16.5 x Ø32 x 0.5t 1
75 Drive Belt 1
PA RT. DESCRIPTION Q’TY
76 Nut 3/8” x 4mm 2
77 Nut 3/8” x 7mm 2
78 Round Head Screw M5 x 25mm 5
79 Spring 1
80 Flat Head Bolt M8 x 85mm 2
81 Stopper 4
82 Nut M8 2
83 Allen Head Bolt M8 x 24mm 4
84 Magnet Holder 1
85 Screw M8 x 24mm 2
86 Bushing 6
87 Seat Carriage Wheel 6
88 Screw M6 x 15mm 4
89 Seat Carriage 1
90 End Cap 1
91 Seat 1
92 Anti-Slippery Pad 2
93 Countersunk Head Bolt M4 x 12mm 8
94 Flat Washer Ø11 x Ø5 x 1.0t 8
95 Sensor Holder 2
96 Universal Wrench 13. 17 1
97 Allen Wrench 6mm 2
98 Tension Knob Pole 1
99 Spring Clip 1
97 Allen Wrench 6mm 2
98 Tension Knob Pole 1
99 Spring Clip 1
98 Tension Knob Pole 1
99 Spring Clip 1