Trust Care Let's Shop User manual

SERVICE MANUAL
Let’s Shop Outdoor rollator.
From Trustcare.

TABLE OF CONTENTS
Exchange of front and rear wheel Page 3
Exchange of rear wheel mounting plate Page 4
Exchange of brake yoke Page 6
Exchange of brake housing and brake lever Page 7
Exchange of front fork and bearings Page 9
Exchange of seat and seat mounting set Page 10
Exchange of brake wire Page 11
Exchange of handle tube Page 13
Mounting of linkage arm Page 15
Exchange of height adjustment button Page 16
Exchange of middle joint folding cross Page 17
Page 18
Art. No. LS317
Art. No. LS323
Art. No. LS328
Art. No. LS306
Art. No. LS318
Art. No. LS324, LS310
Art. No. LS305
Art. No. LS307, LS308
Art. No. LS312, LS321
Art. No. LS319
Art. No. LS326
Art. No. LS311
Exchange of unfold hook
Notes
Exploded view of brake assembly
Page 19
Page 20
Disassembling the brake assembly Page 21
Exploded view of handle assembly Page 22
Disassemling the handle assembly Page 23

Let’s Shop Spare part. Art. No. LS317.
Groove
3. www.trustcare.se
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
Exchange of front or rear wheel.
1. Unscrew the wheel cap. 2. To replace the rear wheel, open
the retaining ring (snap-ring) with
pliers.
replaced with a new one.
4. Use the pliers to lock the new
the axle.
5. Screw the fender and the wheel
cap back in place.

9. Use the pliers to lock the snap-ring
firmly into the groove on the axle.
Groove
Page 1.Exchange of rear wheel mounting plate.
Let’s Shop Spare part. Art. No. LS323
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
2. Unscrew screw
4. Remove the screw from the
brake assembly and wheelplate.
1. Put the handle in lowest position. 3. Pull out the brake assembly
from the rear leg.
7. Remove the wheel from the old
mounting plate
8. Put the wheel on the new
mounting plate.
5. Pull out the rear wheel plate from
the brake assembly
6. To remove the wheel, remove the
retaining ring (snap-ring) with a pliers.
4. www.trustcare.se

Let’s Shop Spare part. Art. No. LS323
Page 2.Exchange of rear wheel mounting plate.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
13. Make sure the brake wire (1) and
brake pad (2) are connected.
15. For left side Make a loop on the
wire as above. Important! See page 21
16. For right side Make a loop on the
wire as above. Important! See page 21
14. Tighten the screw located at
the upper and lower locations.
18. Push the whole assembly into
the rear leg and secure the Screw.
17. Check the function of the brake.
5. www.trustcare.se
10. Put back the wheelcap. 11.If the brake parts were removed
Re-assemble them. See page 21.
12.Check that your brake parts is
2
1
assemblied as above. See page 21.

Let’s Shop Spare part. Art. No. LS328.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
6. www.trustcare.se
2. Unscrew the screw. 3. Pull out the brake assembly
from the rear leg.
6. Secure the screws for the brake
assembly.
7. Push together and secure with
the screw.
Exchange of brake yoke.
4. Remove the screw and open
the brake assembly.
5. Remove the old brake yoke (1). Insert the new brake yoke (2)
and assembly together with wire.
6. Make a wire loop.
Important! See page 21
1. Push the handle down to lowest
position.
1
2

7. www.trustcare.se
Let’s Shop Spare part. Art. No. LS306
Page 1.Exchange of brake housing and brake lever.
1. Unscrew the two screw and remove the height
adjustment button components.
2. Lower the handle to lowest position.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
3. Unscrew the screw.4. Pull out the brake parts. See page
20-21 for detailed view.
6. Unmount the wire.
Important! See page 21.
7. Pull out the handle tube from
the frame.
Important! See page 22-23.
8. Put on the new brake housing/ brake
lever and screw on the two screws
holding the brake housing.
5. Unscrew the screw on
the rear and front side.

8. www.trustcare.se
Page 2.Exchange of brake housing, brake lever.
10. Put together the brake assembly.
Important! See page 21
Let’s Shop Spare part. Art. No. LS306.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
11. Screw together the brake
assembly.
13. Screw in the screw tosecure the brake assemly
to the frame.
12. Insirt the rear brake assembly into the frame.
14. Screw the height adjustment
mechanism back in place.
9. Reattach the brake wire.

9. www.trustcare.se
Let’s Shop Spare part. Art. No. LS318.
Exchange of front fork and bearings.
1. Remove the small screw and pull out the front wheel
assembly.
2. Sepparate the front fork and bushing.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
3. Unscrew the wheelcap screw, remove the C-clip
and remove the wheel from the fork.
4. Mount the wheel on the new fork with clip C and screw
B including the two ball bearings.
6. Push the front fork assembly in position
and secure with the small screw.
5. Mount the new bearing into the front leg of the
rollator.

5. Complete view of the disassembled seat.
Let’s Shop Spare part. Art. No. LS310, LS324
10. www.trustcare.se
Let’s Shop Service Manual.Revision version No: 1 – Nov 2019
Exchange of seat and seat mounting set.
1. Partly fold the rollator so that the
seat is loose and not stretched.
2. Use allen key to unscrew
the seat screw.
3. Remove the fabric band from the
unfold hook.
4. If the seat is to be exchanged, screw of the dome
nuts and pull out the seat from the metal tubes.
6. Screw back the seat screws. Use an allen key for
indexing the fabric.
5. Put back the seat strap in the key ring.

Let’s Shop Spare part. Art. No. LS305.
Page 1.Exchange of brake wire.
1. Unscrew the screws and remove
the height adjustment. See page 23
2. Unscrew the screws and pull out
the brake assembly.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
3. unscrew the screws on the
brake assembly.
6. Unscrew the screw on the handle
and pull out the brake mechanism.
4. Disconnect the wire and pull out
the handle tube from the frame.
5. Important! See page 23-24
8. Remove the old brake wire entirely
from the frame and the handle.
Important! See page 23-24
7. Insert the new brake wire and
reassembly. Important! See page 21
9. Insert the new wire in the handle
tube from bottom and up.
11. www.trustcare.se

Page 2.Exchange of brake wire.
12. Screw together the brake
assembly and rear wheel plate.
11.Assembly the brake parts
as above. Important! See page 21
10. Attach the wire tothe adjustment
screw and screw in the mechanism.
Let’s Shop Spare part. Art. No. LS305.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
15. Reassembly the height
adjustment parts.
13. Push the rear wheel assembly
in place.
12. www.trustcare.se
14. Secure with the screw.

Let’s Shop Spare part. Art. No. LS307, LS308.
Page 1.Exchange of handle tube.
1. Unscrew the screw.
Pull out the rear wheel assembly
2. Unscrew screw A and remove
the height adjustment. See page 23.
Let’s Shop Service Manual. Revision version No: 1 – Nov 2019
3. Unscrew the screws.
6. Unscrew the screw on the handle
and pull out the brake mechanism.
4. Disconnect the wire. See page 21.5. Remove the bottom plug and take
out the wire. See page 23.
13. www.trustcare.se
8. Remove the wire from the old
handle tube. Use the new handle
and assembly.
9. Move the plastic bushing from the
old handle tube tothe new one.
9. Put togheter the rearleg assembly,
Important! See page 21

Page 2.Exchange of handle tube.
12. Mount the brake wire on the new
brake housing and secure the screws.
11. Push the rearwheel assembly
in position.
10. Screw together the rear wheel
assembly.
Let’s Shop Spare part. Art. No. LS307, LS308.
Let’s Shop Service Manual. Revision version No: 2 – Nov 2019
14. www.trustcare.se
13. Screw the height adjustment
mechanism back in place.

1. Drill out the rivets or unscrew the screws that hold
the linkage arm to the metal frame of the rollator.
2. Above is Left and Right linkage arm.
Let’s Shop Spare part. Left Art. No. LS312. Right Art. No. LS321.
15. www.trustcare.se
Let’s Shop Service Manual. Revision version No: 2 – Nov 2019
Mounting of linkage arm.
4. Mount the parts using screws, washers, and nuts.3. Mount the new linkage arm. On the left side the
hook for folding and the spring should also be mounted.
Left
Right

Let’s Shop Spare part. Art. No. LS319.
Exchange of height adjustment button.
Let’s Shop Service Manual. Revision version No: 2 – Nov 2019
1. Unscrew screw A and remove the damaged height
adjustment.
2. The new height adjustment button consists of four
parts.
3. Check that the holes in the plastic bushing, the frame
and the handle tube correspond.
16. www.trustcare.se

1. Drill out the center rivet. The rivet is then exchanged with a screw and nut. See below.
2. The tubes of the folding cross should be placed between the washers in this order according to this sketch.
3. Tighten the dome nut securely. Fix the nut with a drop of Loctite so it will not fall off. The metal sleeve serves as
a fixture peg for the hook when the rollator is folded.
Front side
of rollator
Rear side
of rollator
Front side
of rollator
Rear side
of rollator
Let’s Shop Spare part Art. No. LS326.
17. www.trustcare.se
Let’s Shop Service Manual.Revision version No: 2 – Nov 2019
Mounting the middle joint of the folding cross.

18. www.trustcare.se
4. Mount the new screws, the new hook and the spring. The spring must
be placed around the two screws and locked into the hole in the hook.
5. Adjust the screws so that the hook can easily rotate
and still fits smoothly into the slot in the linkage arm.
Let’s Shop Spare part. Art. No. LS311.
1. Partly fold the rollator so that the seat is loose and
not stretched.
6. Put the fabric band into the slot in the unfold hook.
Adjust the
band so that the hook locks the
rollator in open position and releases when you lift the
seat in the middle opening.
Let’s Shop Service Manual. Revision version No: 2 – Nov 2019
Exchange of the unfold hook.
2. Remove the fabric band from the unfold hook.

19. www.trustcare.se
Notes

20. www.trustcare.se
Exploded view of brake assembly
1
2
3
4
5
6
7
8
9
Brake assembly parts
1. Brake wire guide
2. Brake wire
3. Brake wire spring
4. Outer brake detail
5. Inner brake detail
6. Brake adjustment wheel
7. Brake plastic cover
8. Brake yoke
9. Rear Fork plate