TruVision TVD-6102 User manual

P/N 1073684-EN • REV C • ISS 09JUN21
TruVision HD
-TVI Dome
Camera
Installation Guide

Installation Guide 1
Contents
Product overview 2
Package contents 3
Camera description 7
Installation 10
Installation environment 10
Mounting the HD-TVI fixed lens dome
camera (TVD-6102) 12
Mounting the HD-TVI VF motorized lens
dome camera (TVD-6101, TVD-6103,
TVD-6104, TVD-6105) 15
Specifications 20
Contact information and manuals 21
Legal and regulatory information 22

2 Installation Guide
Product overview
This is the installation guide for TruVision
HD-TVI camera models:
HD-TVI fixed lens dome camera:
TVD-6102 (2MPxDome, 2.8 mm lens)
HD-TVI VF motorized lens dome camera:
TVD-6101 (720P Dome, 2.7 to 13.5 mm
lens)
TVD-6103 (2MPxDome, 2.7 to 13.5 mm
lens)
TVD-6104 (5MPxDome, 2.7 to 13.5 mm
lens)
TVD-6105 (8MPxDome, 2.7 to 13.5 mm
lens)
Go to “Contact information and manuals” on
page 21 for information on where to
download the configuration manual for these
cameras.

Installation Guide 3
Package contents
Check the package and contents for visible
damage. If any components are damaged or
missing, do not attempt to use the unit; contact
the supplier immediately. If the unit is returned,
it must be shipped back in its original
packaging.
HD-TVI VF fixed lens dome camera (TVD-
6102)
Camera with
power and video
output cable
harness (cables
not shown)
4 screws and 4
anchors

4 Installation Guide
Template
Installation guide
•Torx wrench
•12 VDC
connector: Two
terminal
connector with
positive and
negative
indicators
•Equipment
disposal sheet

Installation Guide 5
HD-TVI VF motorized lens dome camera
(TVD-6101, TVD-6103, TVD-6104, TVD-
6105)
Camera with
power and video
output cable
harness
4 screws and 4
anchors
3 screws to
connect the
camera to the
back box
Template

6 Installation Guide
•Torx wrench •G3/4 cable
adapter
Installation guide
•Equipment
disposal sheet

Installation Guide 7
Camera description
Figure 1: HD-TVI fixed lens dome camera
(TVD-6102)





1. Base
2. Lens assembly
3. Bubble assembly
4. TVI output
5. 12 VDC power
6. TVI/960H analog
switch button

8 Installation Guide
Figure 2: HD-TVI VF motorized lens dome
camera (TVD-6101)





1. Bubble assembly
2. Base
3. Lens assembly
4. TVI output
5. 12 VDC/24 VAC
power
6. TVI/960H analog
(connect wires to
switch to 960H
analog)

Installation Guide 9
HD-TVI VF motorized lens dome camera
(TVD-6103, TVD-6104, TVD-6105)






1. Bubble assembly
2. Base
3. Lens assembly
4. TVI output
5. 12 VDC/24 VAC
power
6. TVI/960H analog
switch button

10 Installation Guide
Installation
This section provides information on how to
install the cameras.
Installation environment
When installing your product, consider these
factors:
•Electrical: Install electrical wiring carefully.
It should be done by qualified service
personnel. Always use a proper 12 VDC
UL listed Class 2 CE certified power supply
or a proper 24 VAC power supply,
depending on the camera. Do not overload
the power cord or adapter.
•Ventilation: Ensure that the location
planned for the installation of the camera is
well ventilated.
•Temperature: Do not operate the camera
beyond the specified temperature, humidity
or power source ratings. The operating

Installation Guide 11
temperature of the camera is between -40
to + 60°C (-40 to 140°F). Humidity is below
90%.
•Moisture: Do not expose the camera to
rain or moisture, or try to operate it in wet
areas. Turn the power off immediately if
the camera is wet and ask a qualified
service person for servicing. Moisture can
damage the camera and also create the
danger of electric shock.
•Servicing: Do not attempt to service this
camera yourself. Any attempt to dismantle
this product will invalidate the warranty and
may also result in serious injury. Refer all
servicing to qualified service personnel.
•Cleaning: Do not touch the sensor
modules with fingers. If cleaning is
necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the
camera will not be used for an extended
period of time, put on the lens cap to
protect the sensors from dirt.

12 Installation Guide
Mounting the HD-TVI fixed lens
dome camera (TVD-6102)
To surface mount a camera
1. Using the template, place it level against
the mounting surface and mark the
position of the mounting holes.
2. Following all local codes, drill and
prepare the mounting holes.
3. Loosen the screws with Torx wrech to
remove the housing.
Drill Template
Hole A: for cables routed through the ceiling
screw hole 1: for Mounting Base
1
1
1
A

Installation Guide 13
4. Securely fasten the mounting base to the
mounting surface with the screws.

14 Installation Guide
5. Using a 75-ohm coaxial video cable,
connect the camera TVI video output to a
TVI DVR, and connect a 12 VDC power
supply to the power cable.
6. Adjust the surveillance angle according to
the figure below.
7. Re-attach the housing to the base.

Installation Guide 15
Mounting the HD-TVI VF
motorized lens dome camera
(TVD-6101, TVD-6103, TVD-6104,
TVD-6105)
To surface mount a camera
1. Place the provided template level against
the mounting surface and mark the
position of the mounting holes.
2. Following all local safety regulations, drill
and prepare the mounting holes.
3. Remove the camera from its back box.

16 Installation Guide
4. Loosen the three screws on the edge of
the bubble assembly with the supplied
Torx wrench.
5. Remove the bubble assembly.
6. Secure the back box to the ceiling with
the supplied screws.

Installation Guide 17
Note: Please remove the rubber
knockout for cable routing outside of the
camera, when required.
7. Using a 75-ohm coaxial video cable,
connect the camera TVI video output to a
TVI DVR, and connect a 12 VDC or 24
VAC.
8. Align the camera with the back box and
tighten the screws to secure the camera
to the back box.

18 Installation Guide
9. Adjust the surveillance angle:
a) View the camera image on a monitor.
b) Rotate the panning table to adjust the
pan direction [0 to 355°].
c) Loosen the tilting lock screw.