TUYA M100 Pro User manual

C
B
D
A
E
1/8 1/4 1/2
Extension block
Details of Parts Included in Package
Quick Installation Guide
M100 Pro
Battery installation
①Connect the battery. ②Close the battery cover.
Change The Battery
②Open the battery cover. ③ Replace the battery
(AA*6)
①Remove the shade.
④Close the battery cover. ⑤Install the shade
on the bracket.
Fast SetupTuya
Hub not included
Quiet MotorExternal Battery
Rod Supported
LR6 6

②
③
①
①Install the trim panel bracket. ②Push the shade to the left and
pressed against the wall.
③Push up the right end of the shade
and put it into the window frame.
④
⑤
④Tighten the safety lock.
Before usage, the safety screw
(protecting the nail-free structure)
must be removed to achieve expansion
and contraction.
In case of the occasion that shade
width is less than the window width
we provide 3 widths of the extension block .
⑤Install the trim panel.
Please read the installation instructions carefully to familiarize yourself with safe and effective usage before use. In addition, keep the installation instructions handy when using the product.
The brackets and screws apply to the wooden window frames, plasterboard walls and concrete walls, but they cannot be installed onto the window frames or ceiling which are not made up of wood,
plasterboard and concrete.
Please check the materials and hardness of the window frames or ceiling before installation.
Make sure to comply with the quantity of brackets and installation location required in the installation instructions when installing the products. Improper installation could cause the shades dropping and
bring damage to health or property.
Please do not hang any items on the product or pull the product roughly or fiercely.
The product is only suitable for indoor use and not for outdoor use.
Please do not use the product in a high heat or humid environment (such as saunas or furnace), or near an open flame.
Please close the window or push the shades up during high winds, otherwise the strong winds could cause the damage to the product or an accident.
Please do not place any items which can interfere with operating the shades within a range of moving up and down.
NOTICE
W
Select an extension block with
appropriate thickness and paste
it to the shade motor end.
1/8
1/4
1/2
W ≤ 1/4
1/4 ＜ W ≤ 1/2
1/2 ＜ W ≤ 1
Outside Mount
Inside Mount
Inside Mount: No Tools-No Drill design allow it no need to drill any holes on your window frame, easy to install
Decide on and mark the positions of
the two brackets with a pencil,
using pencil marks as a guide.
Drill holes at marked locations. Install the trim panel bracket. Hook the headrail of the shade into
the front of the bracket，rotate the
headtail until the back of it securely
snaps into place.
Install the trim panel.
(We suggest marking at 1/3 and 2/3
of the total length of the shade.)
① ② ③ ④ ⑤

Quick Matching
"admin"mode
admin
user
Motor
Emitter
Upper
Confirm
Lower
Confirm
Up
Stop
Down
“S”key
Selector
Switch
③
①
②Press
down
M set key
Indicator light
Front Back
The running direction of the blinds is opposite to that of the emitter button. Refer to "motor reversing"
ON
Install the dry
battery.Make sure the
motor is energized.
Step 1
Step 2
Press the motor "M" button for 2”,
the motor rotates back and forth
once.The motor enters the matching
state,(Valid for 60 seconds)
Step 3 Step 4
The switch selects
"admin" mode
Long press "S" for 2” The motor will
rotate back and forth once .Match
successfully
Press 1 time,the shades will be in inching operation.
Press 2 time,the shades will be in continuous operation.
Step 1:Set Highest Point
Use the button on the front to adjust the shade at the position you want.Press for 2
seconds,the motor rotates once.This position is set as the highest point.
Use the button on the front to adjust the shade at the position you want.Press for 2
seconds,the motor rotates once.Then this position is set as the lowest point.
Step 2:Set Lowest Point
In admin mode, you can switch between inching operation and continuous operation, to
adjust it more accurately .
The shade has been adjusted to the best condition before delivery, so it does not need to
be adjusted again. If you want to adjust, please refer to the following advanced setting functions.
Function Key Description

Advanced Settings
"admin"mode
Emitter channel shows slow flash
1.Motor reversing
The running direction of the blinds is oppsite to what shows on the emitter button.
2.Delete emitter matches
"user"mode
In user mode,you can operate and use this product normally without worrying about any
misoperation to the motor.
Add a new emitters
A motor can match one or more emitters
emitters need to be matched. See“emitter quick matching”
There's a quick way to copy it
(1) The switch selects“user”mode.
(2) Operate matached emitter.(Select the channel you want to copy.)
Press"S" 1 time, motor rotates once
Press"S" 1 time again, motor rotates once
(3) Operate emitter to be added.(Select the channel you want to add)
Press"S" 1 time, motor rotates once
Copy complete. Repeat 1-2, delete emitter.
Method 1
Press both
together until the
motor rotates
once
Method 2
Press M key 10”
motor rotates
the third time Motor”M”Key
Operation
Repeated short press
Press for 2”
Press for 5”
Turn-Stop-Turn-Stop
Circular motion
Press for 10” Motor reversing
Press for 15” Restore the factory
Emergency use in
case of travel
The motor feedback Function
Motor rotates once
Motor rotates twice
Motor rotates three twices
Motor rotates four twices
The motor enters the
matching state
/
Motoranzeige
light
Indicator status
Slow flash
Reason
Low battery warning
admin
user
admin
user
admin
user
(1) The swich selects“admin” mode
(2) Press "S" 5 times, motor rotates once.The match is deleted.