TUYA PIR 323-Z-TY User manual

PIR 323-Z-TY
Tuya ZigBee Multi-Sensor
Quick Start Guide

WARNING: Failure to follow these safety notices could
result in 󽘀re,electric shock, injuries, or other damage to the
your property. Please read all the safety notices below
before using the sensor.
•Avoid high humidity or extreme temperatures.
•Avoid long exposure to direct sunlight or strong ultraviolet
light.
•Do not drop or expose the unit to intense vibration.
•Do not disassemble or try to repair the unit yourself.
•Do not expose the unit or its accessories to 󽘁ammable
liquids, gases or other explosives.
Safety Notice

Technical Speci󽘀cations
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Pro󽘀le • ZigBee 3.0
RF Characteristics
• Operating frequency: 2.4GHz
• Range outdoor/indoor: 100m / 30m (Open area)
• Internal PCB Antenna
Physical Speci󽘀cations
Battery • DC 3V (Two pcs AAA batteries)
Indicator • One color LED (Green)
Temp humid range • Temperature Range：-10℃ ~ 50℃
• Humidity Range： 0 ~ 90% RH (±4%RH)
Operating Environment • Temperature：-10℃ ~ +55℃
• Humidity: ≤ 85% non-condensing
Detecting Range(PIR) • Distance: 5m
• Angle：Up/Down 100° , Left/Right 120°
Dimension • 62(L)*62(W)*15.5(H)mm
Mounting Type • Tabletop stand or wall mounting

PIR323-TY is a Tuya Zigbee multi-sensor with built-in
temperature, humidity sensor and PIR sensor which can be
equipped with Tuya gateway and Tuya APP .
This guide will provide you with an overview of the product
and help you get through the initial setup.
Welcome
1
• ZigBee 3.0
• PIR motion detector
• Enviromental temperature and humidity measuring
• Low-power consumption
Features:

Installation
You can mount the multi-sensor to the wall, ceiling or keep
your multi-sensor on a bookshelf or table.
• Please ensure that the surface is clean and secure.
• You can peel o󽗿 the tape on the back or lock it with screws.
2
1. Avoid mounting the Multi-sensor close to pets, air
conditioners, heaters, sunshine or places where the
temperature varies.

2. You need to pay attention to the distance and range of the
sensor when installing.
2.1m
1m 3m 5m
100˚
120˚

Get to Know Your Device
LED Status What it means
Green light 󽘁ashes once Motion detected
Green light keeps 󽘁ashing Enter network con󽘀guration
mode
LED Indicator
LED Indicator Reset Button
3
Reset Button
Reset: Press and hold the reset button for 5 seconds, green
light will start 󽘁ashing, and then the device will automatically
enter the network con󽘀guration mode.

4.1 To get started, you will need:
• A Tuya Zigbee Gateway
• A mobile phone with the speci󽘀ed APP installed.
4.2 Adding to the gateway's network
1. Set your gateway to permit joining (see your gateway's
manual).
2. Ensure that the sensor is within the signal range of the
gateway, and install the sensor with two pcs AAA battery,
then press reset button for 5 seconds, and green light will
start flashing which means the device will automatically
enter the network con󽘀guration mode.
3. Wait for the sensor to be automatically added to the
gateway. If the green light stops blinking, the gateway is
successfully added.
NOTE: If the adding is failed, please reset the sensor and try
again.
Con󽘀gure Network
4