Two Brothers Racing 005-2350406V User manual

2009 Kawasaki
KX250F
Slip-on Exhaust System with M-7 Canister
Part # 005-2350406V / 005-2350407V
V.A.L.E.
VARIABLE AXIS LOCKING EXHAUST
TM
Parts List
IMPORTANT - PLEASE READ CAREFULLY
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
We recommend that this performance part be installed by a qualied
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions rst before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Installation Instructions
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on a centerstand
or ideally a service lift.
2. Remove right side panel.
3. Remove upper muffler mounting bolt.
4. Remove lower muffler mounting bolt & muffler clamp.
5. Remove OEM muffler assembly.
6. Assemble the V.A.L.E.™ unit. Use the 4 (four) 6 x 14mm
socket head cap screws and split lock washers to loosely
attach half X-Lite™ ring to muffler inlet. Attach slip tube to
muffler and attach the other half loosely.
7. Slip S-bend tube of V.A.L.E.™ muffler assembly into head
pipe. Use the supplied 8x30mm Flange bolt for muffler
mount and OEM bolt for midpipe bracket. Leave loose for
now.
8. Making sure that the V.A.L.E. ™ assembly is oriented
correctly, securely tighten lower muffler mounting bolt.
9. Securely tighten the 4 (four) 6 x 14mm hex head bolts of
the V.A.L.E. assembly. (See V.A.L.E.™ Assembly Detail)
10.Securely tighten the upper muffler mounting bolt.
11.Double check to make sure that all hardware is securely
tightened and re-install side panel.
12.Re-install the side panel.
13.Before you run the bike, clean off all fingerprints and dirt, as
any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and
enjoy. It is normal for some white smoke to appear the first
time you start the bike. This is packing/manufacturing oil
from inside the pipe burning off. Check for gaps or leaks.
If you find a leak, a little high temperature silicon sealant
should fix it. After 50 to 100 miles, recheck all fasteners for
tightness.
Qty. Description Part Number
1 KX250F Muffler Canister M-7 Aluminum Varies
1 KX250F Stainless Steel S-Bend Slip-On 005-23504S
1 HARDWARE KIT 005-235-3
2 X-Ring (half) 005-7-2-3
1 8x30mm Flange bolt 005-FB830
1 5mm Long Handle Ball end hex key 005-9-18610
4 Split Lock Washer 005-WL6
4 6x14mm Socket Head Cap Screw 005-SH614
1 TBR Sticker Kit 015-10212
1 Spark Arrestor (Installed) 005-106S
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles.This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Muffler Inlet
X-Lite™ Ring
Slip Tube
V.A.L.E.™ Assembly Detail

005-2350406V
Qty. Description Part Number
1 KX250F Muffler Canister M-7 Aluminum 005-236-206M
1 KX250F Stainless Steel S-Bend Slip-On 005-23504S
1 HARDWARE KIT 005-235-3
2 X-Ring (half) 005-7-2-3
1 8x30mm Flange Bolt 005-FB830
1 5mm Long Handle Ball end hex key 005-9-18610
4 Split Lock Washer 005-WL6
4 6x14mm Socket Head Cap Screw 005-SH614
1 TBR Sticker Kit 015-10212
1 Spark Arrestor (Installed) 005-106S
2009 Kawasaki
KX250F
Slip-on Exhaust System with M-7 Canister
Part # 005-2350406V / 005-2350407V
V.A.L.E.
VARIABLE AXIS LOCKING EXHAUST
TM
005-2350407V
Qty. Description Part Number
1 KX250F Muffler Canister M-7 Aluminum 005-236-207M
1 KX250F Stainless Steel S-Bend Slip-On 005-23504S
1 HARDWARE KIT 005-235-3
2 X-Ring (half) 005-7-2-3
1 8x30mm Flange Bolt 005-FB830
1 5mm Long Handle Ball end hex key 005-9-18610
4 Split Lock Washer 005-WL6
4 6x14mm Socket Head Cap Screw 005-SH614
1 TBR Sticker Kit 015-10212