TYAN FT72-B7015-LE Quick start guide

http://www.tyan.com
1
TYAN®FT72
B7015-LE
Service Engineer’s Manual

http://www.tyan.com
2

http://www.tyan.com
3
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any material contained herein, may be reproduced
without written consent of manufacturer.
Copyright 2012 MiTAC International Corporation. All rights reserved. TYAN®
is a registered trademark of MiTAC International Corporation.
Version 1.0a
Disclaimer
Information contained in this document is furnished by MiTAC Computer
Corporation and has been reviewed for accuracy and reliability prior to
printing. TYAN®assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of TYAN®products including
liability or warranties relating to fitness for a particular purpose or
merchantability. TYAN®retains the right to make changes to produce
descriptions and/or specifications at any time, without notice. In no event will
TYAN®be held liable for any direct or indirect, incidental or consequential
damage, loss of use, loss of data or other malady resulting from errors or
inaccuracies of information contained in this document.
Trademark Recognition
All registered and unregistered trademarks and company names contained
in this manual are property of their respective owners including, but not
limited to the following.
TYAN®is a trademark of MiTAC Computer Corporation.
Intel®is a trademark of Intel Corporation.
AMI®, AMIBIOS®and combinations thereof are trademarks of AMI
Technologies.
Microsoft®, Windows®are trademarks of Microsoft Corporation.
Winbond®is a trademark of Winbond Electronics Corporation.
Portable Document Format (PDF) is a trademark of Adobe Corporation.

http://www.tyan.com
4
FCC Declaration
Notice for the USA
Compliance Information Statement (Declaration of Conformity
Procedure) DoC FCC Part 15: This device complies with part 15
of the FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following conditions:
·This device must not cause harmful interference.
·This device must accept any interference received, including
interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003. Cet
appareil numérique de la Classe A est conforme à la norme NMB-003
du Canada.
Notice for Europe (CE Mark)
This product is in conformity with the Council
Directive 2004/108/EC.
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. There will be danger of explosion if
battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery according
to manufacturer instructions and in accordance with your local regulations.

http://www.tyan.com
5
About this Manual
This manual provides you with instructions on installing your
FT72-B7015-LE. This Manual is intended for experienced users and
integrators with hardware knowledge of personal computers.
This manual is consisted of the following parts:
Chapter1: Provides an introduction to the FT72-B7015-LE
barebones, standard parts list, describes the external
components, gives a table of key components,
and provides block diagrams of the system.
Chapter2: Covers procedures on installing the CPU, memory
modules, add on card and hard drives.
Chapter3:
Covers removal and replacement procedures for
pre-installed components.
Appendix :
Describes the differences between motherboard
BIOS and system BIOS; list the cable connection and
FRU part tables for reference of system setup;
and technical support in case a problem arises
with your system.
For information on the mainboard, please refer to the attached mainboard
user’s manual. You can find the detailed description about jumper and BIOS
settings from the mainboard manual.

http://www.tyan.com
6
SAFETY INFORMATION
Before installing and using FT72-B7015-LE, take note of the following
precautions:
·Read all instructions carefully.
·Do not place the unit on an unstable surface, cart, or stand.
·Do not block the slots and opening on the unit, which are provided for
ventilation.
·Only use the power source indicated on the marking label. If you are not sure,
contact the power company.
·The unit uses a three-wire ground cable, which is equipped with a third pin to
ground the unit and prevent electric shock. Do not defeat the pur-
-pose of this pin. If you outlet does not support this kind of plug, contact
your electrician to replace your obsolete outlet.
·Do not place anything on the power cord. Place the power cord where it will
not be in the way of foot traffic.
·Follow all warnings and cautions in this manual and on the unit case.
·Do not push objects in the ventilation slots as they may touch high volta-
-ge components and result in shock and damage to the components.
·When replacing parts, ensure that you use parts specified by the manuf-
-acturer.
·When service or repairs have been done, perform routine safety checks
to verify that the system is operating correctly.
·Avoid using the system near water, in direct sunlight, or near a heating
device.
·Cover the unit when not in use.

http://www.tyan.com
7
Table of Contents
Chapter 1: Overview......................................................................9
1.1 About the TYAN FT72-B7015-LE............................................9
1.2 Product Models......................................................................10
1.3 Features ................................................................................11
1.4 Standard Parts List................................................................13
1.4.1 Box Contents..................................................................13
1.4.2 Accessories....................................................................15
1.5 About the Product..................................................................16
1.5.1 System Front View .........................................................16
1.5.2 System Rear View..........................................................16
1.5.3 LED Definitions...............................................................17
1.5.4 Motherboard Layout .......................................................18
1.5.5 Jumpers & Connectors...................................................19
1.5.6 System Block Diagram...................................................24
1.5.7 Internal View...................................................................25
Chapter 2: Setting Up..................................................................27
2.0.1 Before you Begin............................................................27
2.0.2 Work Area.......................................................................27
2.0.3 Tools...............................................................................27
2.0.4 Precautions.....................................................................28
2.1 Installing Motherboard Components .....................................29
2.1.1 Removing the Chassis Cover.........................................29
2.1.2 Installing the CPU and Heatsink.....................................30
2.1.3 Installing the Memory .....................................................33
2.1.4 Installing Expansion Cards.............................................36
2.1.5 Installing Hard Drives .....................................................40
2.2 Rack Mounting.......................................................................41
2.2.1 Installing the Server in a Rack........................................41
2.2.2 Installing the inner Rails to the Chassis .........................42
2.2.3 Installing the Outer Rails to the Rack.............................43
2.2.4 Rack mounting the Server..............................................43
Chapter 3: Replacing Pre-Installed Components .....................45
3.1 Introduction..........................................................................45
3.2 Disassembly Flowchart........................................................45
3.3 Removing the Cover............................................................46
3.4 Replacing the Power Supply ...............................................46
3.4.1 Replace the power supply..............................................46
3.4.2 Replacing M7015 Power Distribution Board ..................47

http://www.tyan.com
8
3.4.3 M7015 Power Distribution Board Features ..................48
3.4.4 Replace the M7015 power backplane..........................49
3.4.5 M7015 power backplane Features...............................50
3.5 Replacing M7015 I/O Board ..............................................51
3.6 Replacing the LED Control Board......................................53
3.6.1 M1008 LED Control Board Features............................54
3.6.2 M1008 LED Control Board Connector Pin Definition ...55
3.7 Replacing the System Fan ..................................................56
3.7.1 replacing the rubber screws .........................................57
Appendix I: Redundant Power Behavior ...................................61
Appendix II: Cable Connection Tables ......................................63
Appendix III: FRU Parts Table ....................................................65
Appendix IV: Technical Support ................................................67

http://www.tyan.com
9
Chapter 1: Overview
1.1 About the TYAN FT72-B7015-LE
Congratulations on your purchase of the TYAN®FT72-B7015-LE, a highly
optimized rack-mountable 4U barebone system. FT72-B7015-LE is
designed to support dual Intel®Nehalem-EP/Nehalem-WS 2S processors
and up to 6 channels with 18 DDR3 DIMMs, providing a rich feature set
and incredible performance. Leveraging advanced technology from Intel®,
FT72-B7015-LE server system is capable of offering scalable 32 and 64-bit
computing, high-bandwidth memory design, and lightning-fast PCI-E bus
implementation. FT72-B7015-LE not only enpowers your company in
today’s demanding IT environment but also offers a smooth path for future
application usage.
FT72-B7015-LE uses rack-mountable 4U chassis featuring a robust
structure and a solid mechanical enclosure. All of this provides
FT72-B7015-LE the power and flexibility to meet the needs of nearly any
server application.

http://www.tyan.com
10
1.2 Product Models
Model HDD Bays Graphic card Power supply
B7015F72V2R-LE-N329 Support (2)
internal 2.5”
SATAII HDD
With (3)
NVIDIA M2090 2400W(2+1) PWR supply
B7015F72V2R-LE-N429 Support (2)
internal 2.5”
SATAII HDD
With (4)
NVIDIA M2090 2400W(2+1) PWR supply
B7015F72V2R-LE-N3275 Support (2)
internal 2.5”
SATAII HDD
With (3)
NVIDIA M2075 2400W(2+1) PWR supply
B7015F72V2R-LE-N4275 Support (2) internal 2.5”
SATAII HDD
With (4)
NVIDIA M2075 2400W(2+1) PWR supply

http://www.tyan.com
11
1.3 Features
TYAN FT72B7015-LE (B7015F72V2-LE)
Form Factor 4U Rackmount
Chassis Model FT72
Dimension (D x W x
H) 27.96" x 17.245" x 6.93" (710 x 438 x 176mm)
Motherboard S7015
Board Dimension 16"x19" (406.4x482.6mm)
System
Gross Weight 32KG
Buttons (1) PWR / (1) RST / (1) NMI / (1) ID
LEDs (1) PWR / (1) HDD / (1) Warning
Front Panel
I/O Ports (2) USB ports
Type / QTY (2) 2.5" fixed
Internal Drive
Bay Supported HDD
Interface SATA-II 3.0Gb/s
System Cooling
Configuration FAN (3) 12cm fans
Type ERP1U
Input Range Full-range AC(100-240V)
Frequency 60 Hertz
Output Watts 2400 Watts(1200W+1200W)
Efficiency PFC
Redundancy 2+1(Optional)
Power Supply
Serviceability Hot-swap
Supported CPU
Series Intel Xeon Processor 5500 Series
Socket Type / QTY LGA1366 / (2)
Thermal Design
Power (TDP) wattage Max up to 130W
Processor
System Bus Up to 4.8/ 5.86/ 6.4GT/s with Intel Quick Path
Interconnect (QPI) support
IOH / ICH Intel (2) AC5500 / ICH10R
Super I/O Winbond W83627
Chipset
PCI-E Switch PLX (2) PEX8647
Supported DIMM Qty (9)+(9) DIMM slots
DIMM Type / Speed DDR3 800/1066/1333* RDIMM/UDIMM / * limit 1
per channel for 1333MHz speed
Capacity Up to 144GB at launch w/ dual rank RDIMMs
Memory channel 3 Channels per CPU
Memory
Memory voltage 1.5V

http://www.tyan.com
12
Expansion Slots PCI-E (4) PCI-E Gen.2 x16 slots
Port QTY (4)
LAN Controller Intel 82574L
Connector type D-Sub 15-pin
Resolution 1600x1200
Graphic
Chipset Aspeed AST2050
USB (2) ports
VGA (1) D-Sub 15-pin port
I/O Ports
RJ-45 (4) ports
Chipset Winbond W83793G
Voltage Monitors voltage for CPU, memory, chipset &
power supply
Temperature Monitors temperature for CPU & system
environment
System
Monitoring
LED Fan fail LED indicator / Over temperature
warning indicator
Onboard Chipset Onboard Aspeed AST2050
AST2050 IPMI
Feature
IPMI 2.0 compliant baseboard management
controller (BMC) / BIOS update / USB 2.0 virtual
hub
Server
Management
AST2050 iKVM
Feature 24-bit high quality video compression / Dual 10/100 Mb/s MAC interfaces
Brand / ROM size AMI / 4MB
BIOS Feature
Plug and Play (PnP) /PCI2.3 /WfM2.0
/SMBIOS2.3 /PXE boot / ACPI 2.0 power
management /Power on mode after power
recovery / User-configurable H/W monitoring
Operating
System OS supported list Please refer to our OS supported list.
FCC (DoC) Class A
Regulation CE (DoC) Yes
Operating Temp. 0° C ~ 55° C (32° F~ 131° F)
Non-operating
Temp. - 40° C ~ 70° C (-40° F ~ 158° F)
Operating
Environment
In/Non-operating
Humidity 90%, non-condensing at 35° C
RoHS RoHS 6/6 Complaint Yes
Barebone (1) F72-B7015 Barebone
Manual (1) BB User's manual
Installation CD (1) TYAN installation CD
Package
Contains
Heatsink / Cooler (2) CHSK-0410, 1366-pin CPU heatsinks

http://www.tyan.com
13
Rail kit (1) CRAL-0150, sliding rail kit
Mounting Ear (1) CEAR-0150, mounting ear kit for FT72
Others (1) 2.5" HDD screw pack
Package
Contains
Cable/Power Cord
(2) CCBL-0312, US type power cord /
(2) CCBL-0313, EU type power cord
(8) CCBL-146I, 2*4pin PWR cable for GPU card
(8) CCBL-146H,2*3pin PWR cable for GPU card
1.4 Standard Parts List
This section describes FT72-B7015-LE package contents and
accessories. Open the box carefully and ensure that all components are
present and undamaged. The product should arrive packaged as
illustrated below.
1.4.1 Box Contents
Component Description
4U FT72 Chassis
S7015GM4NR-LE Main Board
1200W Power Supply

http://www.tyan.com
14
120 x120 x38 MM Fan
M1008
Front LED control Board(R02)
M7015
Rear I/O Board
M7015-PBP
PWR Backplane Board(R01)
M7015-PDB
PWR Distribution board for PCI-E
card(R02)

http://www.tyan.com
15
1.4.2 Accessories
If any items are missing or appear damaged, contract your retailer or
browse to TYAN®’s website for service: http://www.tyan.com.
The Web site also provides information on other TYAN®products,
plus FAQs, compatibility lists, BIOS settings, and more.
1 x TYAN®Motherboard
Drive CD 2 x Heatsink
HDD Screws Power Cables
Left to right: Europe, US
Mounting Ears & Screws Barebone Manual
Rail Kit
Rail with Bracket x 2 Screw Sack

http://www.tyan.com
16
1.5 About the Product
The following views show you the product.
1.5.1 System Front View
USB ports ID button Power button (with LED)
Warning LED
NMI button HDD LED
Reset button
1.5.2 System Rear View
LAN Port USB Port
V
G
A
Port ID LED
Expansion slots
Power Su
pp
l
y
Share BMC

http://www.tyan.com
17
1.5.3 LED Definitions
Front Panel
LED State Color Description
On Green System is turned on
Power LED Off Off Power off
On Green HDD power on
HDD LED Blinking Green HDD active
Warning LED On Red Fan fail/PSU fail/Over
temperature/Over voltage
Rear I/O LED
LED State Color Description
On Green 10Mb/100Mb/1000Mb linked
Blinking Green 10Mb/100Mb/1000Mb activity
RJ-45 Linkage/
Activity(Left) Off Off No LAN linked
On Amber 1000Mb linked/ activity
On Green 100Mb linked/activity
RJ-45 Linkage/
Activity(Right) Off Off 10Mb mode or No LAN linked
NOTE: “Left” and “Right” are viewed from the rear panel.
ID LED
LED State Color Description
On Blue System identified
ID LED Off Off System not identified
NOTE: Press ID button when the system is AC (Alternating Current) on,
then ID LED will show the system is identified with emitting blue light. Users
from remote site could also activate ID LED by input a few commands in
IPMI, detailed software support please visit http://www.tyan.com for latest
AST 2050 user guide.

http://www.tyan.com
18
1.5.4 Motherboard Layout
S7015GM4NR-LE
The diagram is representative of the latest board revision available at the time of
publishing. The board you receive may not look exactly like the above diagram.

http://www.tyan.com
19
1.5.5 Jumpers & Connectors
Jumper/Connector Function
CN18 Board-to-Board Receptacle connector
CN19 USB header
CN43 Front Panel header
CN36/CN37/CN40 FAN connector
CN101 Clear CMOS
CN61 System Intrusion header
CN73 NMI button header
CN74 ID button header
CN10 SATA5
CN11 SATA4
CN12 SATA3
CN13 SATA2
CN14 SATA1
CN15 SATA0

http://www.tyan.com
20
Jumper Placement
CN43: Front Panel header
Pin Signal
1 GND
2 PW_LED+
3 PW_LED-
4 WLED+
5 HDD_LED+
6 GND
7 PWR_SW#
8 P3V3_SB
9 RST_SW#
10 GND
11 SDA
12 SCL
13 GND
14 RXD
Pin_1 15 TXD
CN18
CN43
CN36
CN37
CN40
CN19