Ubiquiti LAP-GPS User manual

LAP-GPS Quick Start Guide
×
5 GHz, 17 dBi, 90° airMAX® AC AP
Model: LAP-GPS
Table of Contents
●Package Contents

●Installation Requirements
●Hardware Overview
●Hardware Installation
●Connecting Power
●Accessing airOS via Wi-Fi
●Installer Compliance Responsibility
●Specifications
●Safety Notices
●Electrical Safety Information
●Limited Warranty
●Compliance
●Declaration of Conformity
●Online Resources
Package Contents
LiteAP GPS

LiteAP GPS Ball Joint Mount
Metal Strap
Gigabit PoE (24V, 0.3A) with
Mounting Bracket

Installation Requirements
● Clear view of the sky for proper GPS operation
● 7 mm socket wrench or screwdriver
● Shielded Category 5 (or above) cabling should be used for all wired
Ethernet connections and should be grounded through the AC ground
of the PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade,
shielded Ethernet cable from Ubiquiti. For more details, visit
ui.com/toughcable
● Surge protection should be used for all outdoor installations. We
recommend that you use two Ethernet Surge Protectors, model
ETH-SP, one near the LiteAP and the other at the entry point to the
building. The ETH-SP will absorb power surges and safely discharge
them into the ground.
Power Cord

Hardware Overview

Power LED
The Power LED will light blue when the device is connected to a power
source.
Ethernet LED

The Ethernet LED will light steady blue when an active Ethernet connection
is made and flash when there is activity.
GPS LED
The GPS LED will light steady blue when there is a strong GPS signal.
Reset Button
To reset to factory defaults, press and hold the Reset button for more than
10 seconds while the device is powered on. Alternatively, the device may
be reset remotely via a Reset button located on the bottom of the Gigabit
PoE Adapter.

Hardware Installation
1.
Ethernet Port
The Gigabit Ethernet port is used to connect the power and should be
connected to the LAN.

2.

3.

4.
Connecting Power

1.
2.

3. Connect the power using:
● included Gigabit PoE Adapter
● PoE switch
Connecting to the PoE Adapter
1. Connect the Ethernet cable from the device to the POE port of the PoE
adapter.
2. Connect an Ethernet cable from your LAN to the LAN port of the PoE
adapter.
3. Connect the Power Cord to the adapter, and then plug the Power Cord
into a power outlet.
Mounting the PoE Adapter (Optional)
1. Remove the PoE Mounting Bracket from the adapter, place the bracket
at the desired location, and mark the two holes.
WARNING: The switch port must comply with the power specifications
listed in this Quick Start Guide.

2. Pre-drill the holes if necessary, and secure the bracket using two
fasteners (not included).
3. Align the adapter’s slots with the tabs of the PoE Mounting Bracket, and
then slide the adapter down.
Accessing airOS via Wi-Fi
Verify connectivity in the airOS® Configuration Interface using the UNMS™
app or Web Portal. Both are available for 15 minutes immediately after you
power on the device. If necessary, you can power cycle the device to
re-enable its Wi-Fi.
UNMS App
1. Download the UNMS app.
2. Connect your device’s Wi-Fi to the SSID named: <model>:<MAC
Address>

3. Launch the app and follow the on-screen instructions.
Web Portal
1. Connect your device’s Wi-Fi to the SSID named: <model>:<MAC
Address>
2. Launch your web browser and go to: http://setup.ui.com
3. Select your Country and Language. You must agree to the Terms of
Use to use the product. Click Continue.
Note: Ensure that DHCP is enabled on your Wi-Fi adapter.
Note: Ensure that your Wi-Fi connection has DHCP enabled.

4. Create a
username and password. Confirm your new password and then click
Save.

The airOS Configuration Interface will appear, allowing you to customize your
settings as needed. For additional details, refer to the User Guide available at
ui.com/download/airmax-ac
Installer Compliance Responsibility
Devices must be professionally installed and it is the professional installer's
responsibility to make sure the device is operated within local country
regulatory requirements.
The Output Power field is provided to the professional installer to assist in
meeting regulatory requirements.

Specifications
LAP-GPS
Dimensions (Mount Not
Included)
360.98 x 124.57 x 71.28 mm
(14.21 x 4.90 x 2.81")
Weight (Mount Not Included)
752 g
(1.66 lb)
Networking Interface
(1) 10/100/1000 Ethernet Port
Antenna Gain
17 dBi
Max. Power Consumption
7.1W
Max. TX Power
25 dBm
Power Supply
24V, 0.3A Gigabit PoE Adapter (Included)

Power Method
Passive PoE (Pairs 4, 5+; 7, 8 Return)
Supported Voltage Range
20 - 26VDC
ESD/EMP Protection
± 24kV Contact / Air
Shock and Vibrations
ETSI300-019-1.4
Wind Survivability
200 km/h (125 mph)
Wind Loading
77 N @ 200 km/h
(17.3 lbf @ 125 mph)
Operating Temperature
-40 to 70° C
(-40 to 158° F)
Operating Humidity
5 to 95% Noncondensing

Certifications
CE, FCC, IC
Operating Frequency (MHz)
US/CA
U-NII-1
5150 - 5250
U-NII-2A
5250 - 5350
U-NII-2C
5470 - 5725
U-NII-3
5725 - 5850
Worldwide
5150 - 5875
Management Radio (MHz)
US/CA
2412 - 2462