Ubiquiti NanoStation 5AC Loco User manual

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 1/18
NanoStat  on Wall Mount Bracket Screws (Qty. 2)
Screw Anchors (Qty. 2) Z  p T  es (Qty. 2) G  gab  t PoE Adapter (24V, 0.5A)
Power Cord
Package Contents
Installat  on Requ  rements
Ph  ll  ps screwdr  ver for wall-mount  ng
Sh  elded Category 5 (or above) cabl  ng w  th dra  n w  re should be used for all
outdoor w  red Ethernet connect  ons and should be grounded through the AC
ground of the PoE.
We recommend that you protect your networks from harmful outdoor env  ronments
and destruct  ve ESD events w  th  ndustr  al-grade, sh  elded Ethernet cable from
Ub  qu  t  . For more deta  ls, v  s  t u  .com/toughcable
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 2/18
Surge protect  on should be used for all outdoor  nstallat  ons. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP, one near the NanoStat  on and
the other at the entry po  nt to the bu  ld  ng. The ETH-SP w  ll absorb power surges
and safely d  scharge them  nto the ground.
Hardware Overv  ew
Ports
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 3/18
Secondary
Ma  n
Reset Button
Power
10/100/1000 Ethernet port used for br  dg  ng and supports software-conf  gurable
PoE passthrough.
10/100/1000 Ethernet port used to connect the power and should be connected to
the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds wh  le the NanoStat  on  s powered on.
LED Panel
The Power LED w  ll l  ght blue when the dev  ce  s connected to a power source.
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 4/18
S  gnal
Ma  n Ethernet
Secondary Ethernet
In a  rOS®, you can mod  fy the threshold value for the w  reless s  gnal strength LEDs
on the W  reless tab under S  gnal LED Thresholds. The LED w  ll l  ght when the
w  reless s  gnal strength  s equal to or greater than the LED’s threshold value. The
default threshold values for these LEDs are shown below:
The LED w  ll l  ght steady blue when an act  ve Ethernet connect  on  s made to the
Ma  n/LAN port and ash when there  s act  v  ty.
The LED w  ll l  ght steady blue when an act  ve Ethernet connect  on  s made to the
Secondary port and ash when there  s act  v  ty.
Hardware Installat  on
1.
2.
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 5/18
Pole Mount
1.
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 6/18
2.
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 7/18
3.
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 8/18
Wall Mount
1.
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 9/18
2.
NS-5AC Qu  ck Start Gu  de

25.02.2020 NS-5AC Quck Start Gude
https://dl.ubnt.com/qsg/NS-5AC/NS-5AC_EN.html 10/18
Connect  ng Power
WARNING: The sw  tch port must comply w  th the power spec  f  cat  ons l  sted  n
th  s Qu  ck Start Gu  de.
NS-5AC Qu  ck Start Gu  de