Ubiquiti Loco5AC User manual

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
NanoStation loco Zip Tie
Package Contents
Installation Requirements
Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor
wired Ethernet connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor environments and
destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For
more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend that you use
two Ethernet Surge Protectors, model ETH-SP, one near the NanoStation loco and the
other at the entry point to the building. The ETH-SP will absorb power surges and safely
discharge them into the ground.
Loco5AC Quick Start Guide

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
Diagram Showing Use of Ethernet Surge Protectors
Hardware Overview
Port View

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
Power LED
Ethernet Port
Reset Button
The Power LED will light blue when the device is connected to a power source.
10/100/1000 Ethernet port used to connect the power and should be connected to the
LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10 seconds
while the device is powered on.
Hardware Installation
1.
2.

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
Pole Mount
1.

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
2.

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
3.

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
Connecting Power
WARNING: The switch port must comply with the power specifications listed in this
“Specifications”.

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
Accessing airOS via Wi-Fi
Verify connectivity in the airOS® Configuration Interface using the UNMS™ app or Web Portal.
Both are available for 15 minutes immediately after you power on the device. If necessary,
you can power cycle the device to re-enable its Wi-Fi.
UNMS App
1. Download the UNMS app.
2. Connect your device’s Wi-Fi to the SSID named: <model>:<MAC Address>
3. Launch the app and follow the on-screen instructions.
Web Portal
1. Connect your device’s Wi-Fi to the SSID named: <model>:<MAC Address>
Note: Ensure that DHCP is enabled on your Wi-Fi adapter.
Note: Ensure that your Wi-Fi connection has DHCP enabled.

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
2. Launch your web browser and go to: http://setup.ui.com
3. Select your Country and Language. You must agree to the Terms of Use to use the
product. Click Continue.
4. Create a username and password. Confirm your new password and then click Save.

Loco5AC Quick Start Guide
https://dl.ubnt.com/qsg/Loco5AC/Loco5AC_EN.html[1/6/2020 4:15:20 PM]
The airOS Configuration Interface will appear, allowing you to customize your settings as
needed. For additional details, refer to the User Guide available at ui.com/download/airmax-
ac
Installer Compliance Responsibility
Devices must be professionally installed and it is the professional installer’s responsibility to
make sure the device is operated within local country regulatory requirements.