Ubiquiti NBE--2AC--13 User manual

NanoBeam BallJointMount LockRing
MetalStrap GigabitPoE(24V,0.5A)with
MountingBracket
PowerCord
PackageContents
InstallationRequirements
Polemounting:7mmsocketwrenchorscrewdriver
Wallmounting:wallfastener(notincluded)
ShieldedCategory5(orabove)cablingwithdrainwireshouldbeusedforall
wiredEthernetconnectionsandshouldbegroundedthroughtheACgroundof
thePoE.
Werecommendthatyouprotectyournetworksfromharmfuloutdoor
environmentsanddestructiveESDeventswithindustrialgrade,shielded
EthernetcablefromUbiquiti.Formoredetails,visitui.com/toughcable
Surgeprotectionshouldbeusedforalloutdoorinstallations.Werecommend
thatyouusetwoEthernetSurgeProtectors,modelETHSP,onenearthe
NanoBeamandtheotherattheentrypointtothebuilding.TheETHSPwill
absorbpowersurgesandsafelydischargethemintotheground.
NBE2AC13QuickStartGuide

HardwareOverview

ResetButton
EthernetPort
PowerLED
EthernetLED
SignalLEDs
Toresettofactorydefaults,pressandholdtheResetbuttonformorethan10
secondswhilethedeviceispoweredon.Alternatively,thedevicemaybereset
remotelyviaaResetbuttonlocatedonthebottomoftheGigabitPoEAdapter.
ThisGigabitEthernetportisusedtoconnectthepowerandshouldbe
connectedtotheLANandDHCPserver.
ThePowerLEDwilllightbluewhenthedeviceisconnectedtoapowersource.
TheEthernetLEDwilllightsteadybluewhenanactiveEthernetconnectionis
madeandflashwhenthereisactivity.
InairOS®,youcanmodifythethresholdvalueforthewirelesssignalstrength
LEDsontheWirelesstabunderSignalLEDThresholds.EachLEDwilllight
whenthewirelesssignalstrengthisequaltoorgreaterthantheLED’s
thresholdvalue.ThedefaultthresholdvaluesfortheseLEDsareshownbelow:
HardwareInstallation
Gototheappropriatemountinginstructions:PoleMountingor“WallMounting”.
Note:TheNanoBeamcanalsobemountedinsideawindowusingthe
NanoBeamWindowMount,modelNBE19WM(soldseparately).For
instructions,seetheNanoBeamWindowMountQuickStartGuide.
PoleMounting
1.

2.
3.
4.

WallMounting
TheNanoBeammustbemounteddirectlytoawoodstudorotherstructurally
stablesurfacetoavoiddamagetothemountingholewhenyouadjusttheaim.
OptionalAccessory
Toenhancestability,youcanusetheNanoBeamWallMountKit,modelNBE
WMK(soldseparately).
Note:Centerscrewincluded.Twooptionalscrews(notincluded)provide
additionalstability.
InstallationInstructions
1.

2.
3.
OR

Fastener(notincluded) NanoBeamWallMountKit
4.
Aiming
1.

2.
ConnectingPower
1.
2.

3.
4.Connectthepowerusing:
includedGigabitPoEAdapter
PoEswitch
WARNING:Theswitchportmustcomplywiththepowerspecifications
listedinthisQuickStartGuide.
ConnectingtothePoEAdapter
1.ConnecttheEthernetcablefromthedevicetothePOEportofthePoEadapter.
2.ConnectanEthernetcablefromyourLANtotheLANportofthePoEadapter.

3.ConnectthePowerCordtotheadapter,andthenplugthePowerCordintoa
poweroutlet.
MountingthePoEAdapter(Optional)
1.RemovethePoEMountingBracketfromtheadapter,placethebracketatthe
desiredlocation,andmarkthetwoholes.
2.Predrilltheholesifnecessary,andsecurethebracketusingtwofasteners(not
included).
3.Aligntheadapter’sslotswiththetabsofthePoEMountingBracket,andthen
slidetheadapterdown.
AccessingairOSviaWiFi
VerifyconnectivityintheairOS®ConfigurationInterfaceusingtheUNMS™appor
WebPortal.Bothareavailablefor15minutesimmediatelyafteryoupoweronthe
device.Ifnecessary,youcanpowercyclethedevicetoreenableitsWiFi.
UNMSApp
1.DownloadtheUNMSapp.
2.Connectyourdevice’sWiFitotheSSIDnamed:<model>:<MACAddress>
Note:EnsurethatDHCPisenabledonyourWiFiadapter.