Ubiquiti LiteBeam LBE-5AC-LR User manual

LBE-5AC-LR Quick Start Guide
Package content
power horn
M4 SEM screws (qty: 8) Metal strips (qty: 3)M8 SEM screws (quantity: 4)
Mounting bracket
Panel reflector central
Gigabit PoE (24 V, 0.3A) con
power receiver
Side Reflector Panels (Qty: 2)
Power cord
Spinning panels (qty.: 2)
Machine Translated by Google

Mounting bracket
We recommend that you protect your networks from harmful outdoor environments
and electrostatic discharge phenomena with Ubiquiti's Industrial Grade Shielded
Ethernet Cable. For more information, visit ui.com/toughcable
Application Examples
installation requirements
LBE-5AC-LR Quick Start Guide
Phillips screwdriver
Category 5 (or higher) shielded cabling with a drain wire must be used for all
Ethernet connections and must be connected to the AC ground of the PoE.
Surge protection must be used on all outdoor installations. We recommend
that you use two surge protectors, model ETH-SP, one near the LiteBeam
and the other at the entry point of the building. The ETH-SP will absorb surge
voltages and safely discharge them to the ground.
13mm wrench
7mm socket wrench or screwdriver
Machine Translated by Google

The exterior mounted LiteBeam AC without the reflector installed provides exterior
to interior coverage only via the 3 dBi powered horn.
Outdoor mounted LiteBeam AC with reflector installed provides directional outdoor
coverage LBE-5AC-LR Quick Start Guide (gain dependent on reflector).
hardware description
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
To restore factory defaults, press and hold the reset button for more than 10
seconds while LiteBeam AC is powered on. You can also remotely reset the
device using the reset button on the bottom of the Gigabit PoE adapter.
The LED indicator will turn solid blue when the device is connected to an
Ethernet network and will blink if there is activity.
Puerto Ethernet
Power LEDs
Supports 10/100/1000 connections and passive PoE. This port must be
connected to the LAN and the DHCP server.
The LED will light blue when the device is connected to a power source.
reset button
LED the Ethernet
Machine Translated by Google

hardware installation
LBE-5AC-LR Quick Start Guide
1.
2.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
Machine Translated by Google

4.
3. LBE-5AC-LR Quick Start Guide
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
6.
5.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
7.
8.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
9.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
10.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
pole mount
1.
Machine Translated by Google

2.
3.
LBE-5AC-LR Quick Start Guide
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
4.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
5.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
6.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
Power connection
WARNING: The port switch must meet the power specifications
listed in this quick start guide.
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
O
Check the connectivity of the airOS® configuration interface using the UNMS™
app or web portal. Both are available for 15 minutes immediately after turning on
the device. If necessary, you can turn on the device to turn your Wi-Fi back on.
Optional
Access to airOS over Wi-Fi
Machine Translated by Google

LBE-5AC-LR Quick Start Guide
Portal web
UNMS application
1. Connect your device's Wi-Fi to the SSID named: :
2. Connect your device's Wi-Fi to the SSID named: :
1. Download the UNMS app
product. Click Continue.
2. Open your web browser and go to: http://setup.ui.com
3. Run the application and follow the instructions on the screen.
3. Select your language and country. You must accept the Terms of Use to use the
Note: Be sure to enable DHCP on your Wi-Fi connection.
Note: Make sure DHCP is enabled on your Wi-Fi adapter.
Machine Translated by Google

The airOS settings interface will open allowing you to customize your settings
as needed. For more information, see the user guide available at ui.com/download/
airmax-ac
LBE-5AC-LR Quick Start Guide
4. Create a username and password. Confirm your new password and then
then click Save.
Machine Translated by Google