Ubiquiti BULLETM2-HP-US User manual

Bullet M2 Compression Seal
Package Contents
Installation Requirements
Shielded Category 5 (or above) cabling with drain wire should be used for all
outdoor wired Ethernet connections and should be grounded through the AC
ground of the PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded Ethernet
cable from Ubiquiti.. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP, one near the B-DB-AC
and the other at the entry point to the building. The ETH-SP will absorb power
surges and safely discharge them into the ground.
* Shown without antenna.
BulletM2-HP Quick Start Guide

Signal LEDs
Hardware Overview
In airOS®, you can modify the threshold values for the wireless signal strength
LEDs on the Advanced tab under Signal LED Thresholds. The default values are
shown below:
BulletM2-HP Quick Start Guide

Ethernet LED
Power LED
Reset Button
Ethernet Port
The Ethernet LED will light steady green when an active Ethernet connection is
made and flash when there is activity.
The Power LED will light green when the device is connected to a power source.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on.
This 10/100 Ethernet port is used to connect the power and should be
connected to the LAN and DHCP server.
Hardware Installation
1.
2.
BulletM2-HP Quick Start Guide

3.
4.
5.
BulletM2-HP Quick Start Guide

6.
7.
BulletM2-HP Quick Start Guide

Accessing airOS
Verify connectivity in the airOS® Configuration Interface.
1. Make sure that your host machine is connected via Ethernet to the device.
2. Configure the Ethernet adapter on your host system with a static IP address on
the 192.168.1.x subnet.
3. Launch your web browser and type https://192.168.1.20 in the address field.
Press enter (PC) or return (Mac).
4. Enter ubnt in the Username and Password fields. Select your Country and
Language. You must agree to the Terms of Use to use the product. Click Login.
The airOS Configuration Interface will appear, allowing you to customize your
settings as needed. For additional details on the airOS Configuration Interface, refer
to the User Guide available at: ui.com/download/airmax
BulletM2-HP Quick Start Guide

You can also manage your device using the Ubiquiti Network Management System.
Setup using the UISP™ app requires the U-Installer, sold separately.
Installer Compliance Responsibility
Devices must be professionally installed and it is the professional installer’s
responsibility to make sure the device is operated within local country regulatory
requirements.
Antena
Select your antenna from the list. Ensure Calculate EIRP Limit is enabled; transmit
output power is automatically adjusted to comply with the regulations of the
applicable country. For a Custom antenna, Antenna Gain is entered manually. Note
the requirements and antenna types listed below.
Cable Loss (When applicable)
Enter the cable loss in dB. Output power is adjusted to compensate for loss
between the radio and the antenna.
Certified Antenna Types
This radio transmitter FCC ID: FCC: SWX-M2BW / IC: 6545A-M2BW has been
approved by FCC / ISED Canada to operate with the antenna types listed below with
the maximum permissible gain for each antenna type indicated. Antenna types not
included in this list or having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Antenna Frequency Gain
Omni 2.4 GHz 13 dBi
Sector 2.4 GHz 17 dBi
Dish 2.4 GHz 24 dBi
Specifications
BulletM2-HP
Dimensions 163.65 x 38.75 x 38.75 mm
(7.48 x 1.53 x 1.53")
Weight 130 g (4.59 oz)
Enclosure Polycarbonate
Networking Interface 10/100 Mbps
Antenna Connector N-Type Connector
LEDs Power, Ethernet,
(4) Signal Strength
Max. Power Consumption 7W
BulletM2-HP Quick Start Guide

BulletM2-HP
Output Power 25 dBm
Power Supply AC to 24VDC, 0.5A Gigabit PoE Adapter
Power Method 24V Passive PoE
(Pairs 4, 5+; 7, 8-)
ESD/EMP Protection ± 24 kV Contact/Air
Operating Temperature -40 to 70° C (-40 to 158° F)
Operating Humidity 5 to 95% Condensing
Shock and Vibration ETSI300-019-1.4
Certifications CE, FCC, IC
Operating Frequency (MHz)
US/CA 2412 - 2462
Worldwide 2412 - 2472
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote
risk of electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements
indicated on the manufacturer’s label. Connection to a different power source than those
specified may result in improper operation, damage to the equipment or pose a fire hazard if
the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided
only by a qualified service technician.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis,
and, where applicable, specify arbitration instead of jury trials or class actions.
Compliance
BulletM2-HP Quick Start Guide

FCC
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
This radio transmitter has been approved by FCC.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
This radio transmitter has been approved by ISED Canada.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
CAN ICES-3(A)/NMB-3(A)
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. l’appareil ne doit pas produire de brouillage;
2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Le présent émetteur radio a été approuvé par ISDE Canada.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux.
IMPORTANT NOTE
Radiation Exposure Statement
BulletM2-HP Quick Start Guide

This equipment complies with radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20 cm between the
radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
AVIS IMPORTANT
Déclaration sur l’exposition aux rayonnements
Cet équipement est conforme aux limites prévues pour l’exposition aux rayonnements dans
un environnement non contrôlé.
Lors de l’installation et de la mise en fonctionnement de l’équipement, assurez-vous qu’il y
ait une distance minimale de 20 cm entre l’élément rayonnant et vous.
Cet émetteur ne doit être installé à proximité d’aucune autre antenne ni d’aucun autre
émetteur, et ne doit être utilisé conjointement à aucun autre de ces appareils.
Australia and New Zealand
Warning: This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
Brazil
Nota: Este equipamento não tem direito à proteção contra interferência prejudicial e
não pode causar interferência em sistemas devidamente autorizados.
Japan
006-000231
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
Country List
AT BE BG CY CZ DE DK EE EL ES FI FR HR HU
IE IT LV LT LU MT NL PL PT RO SE SI SK UK
BFWA (Broadband Fixed Wireless Access) members noted in blue
Note: This device meets Max. TX power limit per ETSI regulations.
BulletM2-HP Quick Start Guide