Ubiquiti PBE-M5-620 User manual

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 1/22
D  sh Reector w  th Mount  ng
Bracket Antenna Feed Rear Hous
 ng
Support Arm Upper Pole Bracket Assembly Lower Pole Bracket
Brace Screws (Qty. 4) Hex Head Bolts (Qty. 5)
Lock Washers (Qty. 5) Flat Washers (Qty. 5) Stab  l  zer Brackets (Qty. 2)
Package Contents
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 2/22
M10x100 Bolts (Qty. 2) M10 Flange Nuts (Qty. 2) M8x150 Carr  age Bolts (Qty. 4)
M8 Flange Nuts (Qty. 4) Pole Clamps (Qty. 2) G  gab  t PoE (24V, 0.5A) w  th
Mount  ng Bracket
Power Cord
Installat  on Requ  rements
Ph  ll  ps screwdr  ver
13 mm wrench
16 mm wrench
Sh  elded Category 5 (or above) cabl  ng should be used for all w  red Ethernet
connect  ons and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor env  ronments
and destruct  ve ESD events w  th  ndustr  al-grade, sh  elded Ethernet cable from
Ub  qu  t  . For more deta  ls, v  s  t u  .com/toughcable
Hardware Overv  ew
Bottom V  ew
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 3/22
Ethernet
Reset Button
Release Button
Th  s G  gab  t Ethernet port  s used to connect the power and should be connected to
the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds wh  le the dev  ce  s powered on. Alternat  vely, the dev  ce may be reset
remotely v  a a Reset button located on the bottom of the G  gab  t PoE Adapter.
After you assemble the PowerBeam, check the Release button;  t should be fully
engaged  n the Release Button Slot of the Rear Hous  ng. Th  s ensures that the
Antenna Feed  s locked  nto place. If you need to remove the Antenna Feed, you
must depress the Release button f  rst.
LEDs
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 4/22
S  gnal
Ethernet
Power
In a  rOS®, you can mod  fy the threshold value for the w  reless s  gnal strength LEDs
on the W  reless tab under S  gnal LED Thresholds. Each LED w  ll l  ght when the
w  reless s  gnal strength  s equal to or greater than the LED’s threshold value. The
default threshold values for these LEDs are shown below:
The Ethernet LED w  ll l  ght steady blue when an act  ve Ethernet connect  on  s made
and ash when there  s act  v  ty.
The Power LED w  ll l  ght blue when the dev  ce  s connected to a power source.
Appl  cat  on Examples
The PowerBeam mounted outdoors w  th the Reector  nstalled prov  des d  rect  onal
outdoor coverage (ga  n  s reector-dependent).
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 5/22
The PowerBeam mounted outdoors w  thout the Reector  nstalled prov  des outdoor-
to-  ndoor coverage us  ng the 3 dB  Antenna Feed only.
Installat  on
1. 
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 6/22
2.
3.
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 7/22
4.
5.
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 8/22
6.
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 9/22
7.
8.
PBE-M5-620 Qu  ck Start Gu  de

15.02.2020 PBE-M5-620 Quck Start Gude
https://dl.ubnt.com/qsg/PBE-M5-620/PBE-M5-620_EN.html 10/22
9.
PBE-M5-620 Qu  ck Start Gu  de