UDI R/C U95 User manual

OPERATING
INSTRUCTIONS
This product supports GPS positioning and is recommended for outdoor flight!
* This wifi camera pinpoint is 5G, please confirm whether the phone is supported.
V1.0
▲This product is suitable for users over 14 years old.
▲Stay away from the rotating propeller
Note
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household
trash. Please contact local environmentalor waste agency or the
supplier of your model or your nearest Li-Po battery recycling center.
Our company's products are improving all the time, design and specifications are
subject to change without notice. All the information in this manual has been
carefully checked to ensure accuracy, if any printing errors, our company reserve
the final interpretation right.
Important
Notice
U95

Propeller A
Front folding
arm
Obstancle
avoidance
switch Power switch
Front folding
arm
Propeller B
Front LED
(Blue)
Propeller B
Rear folding
arm
Rear LED (Green)
Propeller A
Rear folding
arm
Obstancle avoidance switch
Front LED
(Blue)
Optical
flow position
Battery
Fill light
switch
Front Camera
Drone preparation

③
②
①
①
Folding State
②
Rear folding arms unfold
③
Front folding arms unfold
Drone battery charging
Connect the batteries of the drone to the charging line of the original plant, and then
connect to other USB charging sockets.
The indicator of drone battery is keep red when charging.
The indicator of drone battery is keep green when fully
charged.
Battery power is low in the original factory, It must be fully charged before
use.
Warning: Must be attended to while charging
Power adapter (not included)
▲Only use the original USB charging cable.
Input: 5V,2A
Drone battery
Unfolding Instruction

Obstancle avoidance
switch
Fill light switch
Press to unlock the lock
Pull out the battery
Disassem:
Place the battery into the
battery compartment along
the rear of drone.
Installation of drone battery
Transmitter preparation
Phone Holder
Gimbal Rotary
Button
Left stick
GPS switch
Power switch
Speed switch
Video
Right Stick
Return
Photo
Indicator light

Warning: Must be attended to while charging
①
②③
Battery power is low in the original factory, It must be fully charged before use.
Transmitter charging
Connect the transmitter with the charging line of the original plant, and then connect
other USB charging outlets. When charging, the transmitter indicator flashes circularly,
and when charging is completed, the indicator will be on for a long time.
Power adapter (not included)
Original Charging
Line
▲Only use the original USB charging cable.
Input: 5V,2A
Installation of phone holder and phone
④
Place the phone in
the upper and lower
clamps Between, the
clamp will automatically
clamp the mobile phone .
Notice: Don't clip the buttons
on the side of the phone.
②
Disassemble
Pull up the clip on
the mobile phone
①
Press to unlock the lock
①
②
Put the phone clip
onthe back of the quasi-
remote controller
and push it to the end.
Straightening the antenna
Installation
③
Pull up the clip on the mobile phone.

Flight Operations
Mobile phone connect with Drone
Download and install APP: RC-Wing
This software is suitable for mobile phones in the IOS 9.0 or later
and Android 4.4 or later system.For detailed operation, please
check the system “HELP” of APP.
②
The drone is placed on the horizontal ground,long press the power button for 3
seconds to turn on,the front and rear navigation lights cycle flashing,indicating that
the frequency alignment is successful to enter the GPS start search state.
①
Turn on the power.
it indicates the transmitter
entersthe frequency state.
Horizontal Ground
Transmitter connect with Drone
Frequency Pairing

Compass calibration
Rotate the drone horizontally until the transmitter sounds "di... "Level correction to complete.
When the front navigation light turns to long light and the rear navigation light flashes,
enter vertical correction.Rotate the drone vertically until the transmitter sounds "di... "A
sound, vertical correction over. The lights are spinning and flashing.
Horizontal rotation Vertical rotation
Tips: It’s a must to have the right compass adjustment first each time you start
the drone, or it can’t work normally
Gyroscope Calibration
After the calibration of the compass, the right stick
of the transmitter is pushed to the lower right corner
by 45°, and the transmitter emits sound "di", and the
drone light flashes and releases, indicating that the
gyroscope has been calibrated. (drone should be placed
on horizontal ground)
Tips: When the drone doesn’t appear to use the trim correction flight status, or
being hit hard (or falling abnormally). thus cause the difficulties in controlling.
Now frequency making and adjustment are needed again.

After the frequency matching is successful, the drone automatically searches for GPS
signals. When the blue indicator light of the remote control changes from flashing to long
bright, it makes a sound of "di" at the same time, indicating that the GPS connection is
successful. (when the GPS signal is weak or flying indoors, the flight height defaults to
about 4 meters)
GPS Signal Search
①
②
Unlocking/locking the motor
Push the left and right stick inward to the 45°
angle simultaneously.
On standby drone, motor rotation, drone
unlocked.
When the drone is not take off, the motor
stops rotating and the drone is locked.
The drone can only take off when the motor is unlocked.
GPS must be turned off when flying indoors.
Take off
After unlocking the motor, the left stick
slowly pushes up and the drone slowly
rises.
Landing
During the flight, the left stick slowly
pull down , and the drone slowly lands
until landing.

Control stick operation
Counter-
clockwise
turn
Clockwise
turn
Go up
Go down
Fly to
the left
Fly to
the right
Forward
Backward
Left stick Right stick
Return
During the flight, press the " " button,
and the transmitter will sound "di", and
the drone will automatically return to the
take-off point. (during returning, the transmitter
will continuously sound "di". To stop homing,
just press this button again.)
Notice: While returning, the control lever of the transmitter can not control the drone, it must
be waited for the drone to go back to the take-off point. And after the direction of the
drone is directed at the direction of taking off, in this way right stick can control the
drone.
GPS is on by default.
GPS OFF: Press the " " button, the transmitter
will sound "di”and the blue indicator of
the transmitter will go off, it means GPS
will be off.
GPS ON: Press the " " button and the blue
indicator of the transmitter will keep bright.
It means GPS restart.
GPS ON /OFF
Note: this function is only used when the motor is locked.

Speed mode switch
Press "H/L" button, the transmitter will
sound "di.di.di" to enter high speed mode
"H".
Press it again, the transmitter will sound
"di" to enter low speed mode "L".
Press it again, the transmitter will sound
"di.di" to enter medium speed mode "M".
Medium speed default
Gimbal Adjustment
Roll Gimbal Rotary Button, adjust Camera
Angle.
Photo
Press the " " button once to take
a picture and the transmitter will sound
"di".
Video
Press the " " button, the transmitter will
sound "didi" to start recording. Repeat this action
to stop recording and save the video.
①
②
The APP must be authorized to read the phone
gallery to view the aerial photos.
When aerial video is read by computer, it must
have corresponding playback software.

Note: Switch to high speed switch, obstacle avoidance function will be disabled.
Filllightswitch
Obstancleavoidanceswitch
Obstancle avoidance mode is off by default.
Press the “ ”button,the transmitter
will sound “di” to turn on the obstacle
avoidance function,and press again to turn
avoidance function.
The fill light is off by default.Press the
“ ” button,the transmitter will
sound “di” to turn on the fill light,and
press again to turn off.
Low Battery Alarm
Automatic Return
When the drone in low battery, the transmitter will continues to sound "dididi......
dididi", the drone's indicator lights turn from long to bright. After alarming you, the drone
automatically returned to the take-off point.
When the transmitter in low battery,
the transmitter will continues to sound "di...di...di......"
to remind the user to return home and charge the batteries of the transmitter as soon
as possible.

Stuck Protection
When the propeller is stuck and does not rotate, the drone will start the automatic protection
function to stop the motor working.
When the drone is out of the remote control distance, the transmitter will continues to
sound "didi.didi" to alarm the user to return the drone immediately.
Out of range alarm
Out of Control Protection
Out of control protection refers to the flight control system automatically controls the
drone to fly back to the return point after receiving the remote control signal (ie, out of
control), the drone does not have the function of avoiding obstacles during the uncontrolled
return flight. The user can set the return altitude value to avoid obstacles on the way back.
* The remote control is off.
* Flight distance exceeds the effective distance of remote control signal
transmission.
* There is an obstacle between the transmitter and the drone.
* Transmitter signal is disturbed.
Possibility of entry into runaway protection mode

①
②
③
Switching sequence. At first, turn on the power of the transmitter, then turn on the
power of the drone. After the end, turn off the power of the drone first, and then turn
off the power of the transmitter.
Improper operation caused the crash. It is necessary to check and confirm the
connection of the motor, blade or electric pool of the drone and the damage degree,
so that the drone can fly again.
If it is damaged, please replace it with new accessories, otherwise it will easily cause
flight accidents.Battery must be removed when the drone is not in use.
Attention
Parts Replacement
Propeller Replacement
Propeller
Folding arm
Motor Remove the
propeller
assembly
Remove propeller components in serial order. Operation in the opposite direction dring
installation. The propeller is divided into AB, corresponding to the letter on the folding
arm. Please make sure it is installed correctly,otherwise it cannot fly.
A
A
②
Remove the screws
using a screwdriver
①

Troubleshooting
Problem
The transmitter
indicator light
is off
Unable to
frequency
Under-powered
or can not fly
Abnormal flight
cannot altitude
hold and yaw
serious
The drone
indicator light
is off
Solution
2) Please make sure turn on the power.
1) The battery is low, please charge in time.
1) Please refer to the manual to operate again.
2) Make sure signal interference nearby and keep away.
3) The electronic component is damaged for frequent crash.
1) Make sure the propeller is damaged or replace a new one.
2) When the battery is low, please charge it in time.
1) Make sure the propeller is it damaged ? If so, replace the propeller.
2) Confirm whether the body shell is damaged and replace it.
3) Restart and “correct”according to the instructions after 10
seconds of shutdown.
1) When the battery is low, please charge it in time.
2) Replace the damaged battery with a new one.
3) Over-powered protection, restart after 30 seconds of shutdown.

FCC Note
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interferencein a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interfere nce by one or more of the following
measures:
●Reorient or relocate the receiving a ntenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which
thereceiver is connected.
WARNING: Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
The equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly
approved in the instruction manual. Modifications not authorized by the manufacturer may
void user’s authorityto operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition with out restriction.
FCC Radiation Exposure Statement

DANGER!
Only suitable for age 14+
Warning: The product should only be used by adults and children over 14 years.
Adult supervision is required for children under 14 years.
Hinweis: Dieses Produkt ist für die Erwachsene und die Kinder ab 14 Jahren.
Die kinder unter 14 Jahren müssen von Erwachsenen beaufsichtigt
werden.
Avertissement:
Ce produit est destiné aux adultes et aux enfants de plus de 14 ans.
Les enfants de moins de 14 ans doivent être surveillés par des adultes.
Avvertimento: Questo prodotto è destinato all'uso per i adulti e bambini di età
superiore ai 14 anni. I bambini di età inferiore ai 14 anni devono
essere sorvegliati da un adulto.
Advertencia: Este producto es para adultos y niños mayores de 14 años.
Los niños menores de 14 años deben ser supervisados por adultos.
WARNING
MADE IN CHINA
Address: Guangfeng Industrial Zone, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, CN
Manufacturer: UDIRC TECHNOLOGY CO., LTD