UDI R/C U64 User manual

USER
MANUAL
U64
▲This product is suitable for users over 14 years old.
▲Stay away from the rotating propeller.
▲Read the<important statement and safety guidelines >carefully..
Suitable for indoor flight

Slider drone pattern
Motorboat drone pattern
Front
Front
Forward
Backward
Drone-LED
Forward
Backward
OFF ON
Charging port
Propeller A
Propeller B
Propeller A
Propeller B
Charging-LED
OFF ON
Charging port
Ready Before Take Off
Drone preparation
2

①Wings installation
Drone tail installation
Slider drone decoration propeller installation
Slider drone doll and hang lift assembly
①
①
Installation: Distinguish left and right wings,
aim at the body hole to push until end.
Disassembly:
Apply force to pull the wings
out is fine.
Installation: Firstly connect the drone tail to the drone body hole and then rotate the
drone tail, push the upper buckle of drone tail to the drone body buckle.
Disassembly: Pull out the drone tail buckle and then rotate to disassemble.
Installation: Make sure the slider drone decoration
propeller to aim at the front buckle and push until end.
Disassembly: Apply force to pull out the decoration
propeller.
Installation: Hang the doll to the lift and then install the hang lift to the arm slot in
the drone bottom.
Disassembly: Pull out one side hook of the hang lift, and then another side to
remove the doll.
②
③
④
④
Left Wing
Right Wing
Rear
Front
Slider drone parts installation
③
②
3

②Protection rack installation
Distinguish front and rear of the
motorboat, install the front and
rear guards, and put the hands
to the front guard, finally put on
the doll’s handle.
①Slider drone doll installation
①
Installation: Make sure distinguish the doll’s front and rear soles, put into the front
toes and then press down the rear foot is fine.
Disassembly: Lift the rear foot and then pull
out is fine.
②
②
②
②
Front
Front
Rear
Rear
Motorboat parts installation
Charging port
Charging Instruction
Battery power is insufficient in the original plant. It must be charged saturated
before it can be used.
Original charging cable
USB adapter
(Not included)
②①
▲Only use the original charging cable;
suggest select adapters with output
current of 5V 2A .
Connect the original charging cable with the drone, and then connect other USB
charging port. The drone red charging-LED keeps bright when charging and the light
turns green when fully charged.
The drone power button should be
turned off when charging.
4

Left stick /
Trimmer (Press down)
Auto-demo
Take Off / Landing /
Emergency Stop Button
Right Stick
Speed Switch
Heading Hold Mode
Power Switch Motorboat /
Slider drone
Mode Switch
Power-LED
Transmitter preparation
Battery cover
Back side of the transmitter
Battery installation
Open the battery cover on the back side of the transmitter ，according to the "+-"
electrode instruction in the battery groove, place the battery with the same type of
saturated power (battery not include).
3×1.5V AAA
Alkaline Batteries
5

③
①Power on the drone, the drone indicator will change from fast flash to slow flash,
and enter frequency pairing.
The Motorboat are placed
on the horizontal ground.
Hold the drone to keep balance.
* Stay away from the propellers to avoid injury.
②
Short press to open/close
Press the flip switch and select the
corresponding mode.
Flight Operation
Transmitter connect with Drone
Frequency Pairing
Turn on the power on the transmitter, the power-LED will flash quickly.
Pull the left stick until bottom and
then release, and the transmitter
power-LEDwill keep bright and
sound beep to show frequenc
pairing successful.
6

Tip: Do not use the emergency stop function unless in emergency situation.
Take off
Landing
Don’t operate the left stick during landing,
otherwise the current command will automatically fail.
Control stick operation
Left stick
Counterclockwise turn
Clockwise turn
Go up
Go down
Right stick
Fly to the left
Fly to the right
Forward
Backward
After the frequency pairing is successful, press the "take off/land" button, the transmitter
will sound "di", and the drone will automatically rises and flies at an altitude of about 1.2m.
During the flight, press the "take off/land"
button, the transmitter will sound "di",
and the drone will land slowly until landing.
Emergency Stop: During the flight, press " take off/land" button for about 2 seconds,
the transmitter will sound "di.di..." and the drone crashes directly.
7

Press “Automatic show”，the drone
will fly forward and turn back to the
original position.
Auto-demo
Speed mode switch
Press the "H/L" button, the transmitter will sound "di.di.di", to enter High Speed Mode "H".
Press again, the transmitter will sound "di", to enter Low Speed Mode “L”.
Press again, the transmitter will sound “di.di”, to enter Middle Speed Mode “M”.
Medium speed default
Low speed: suitable for beginners to practice
without wind.
Medium speed: suitable for skilled operator
operating in light breeze.
High speed: suitable for professional operation
in outdoor wind resistance.
8

Front Front
Rear
Rear
Heading Hold Mode
①
②
The default setting is NOT Heading Hold Mode.
Heading Hold Mode means that the user can operate the aircraft without having to
distinguish directions. This mode is suitable for beginners, or when it is difficult to
distinguish the forward and backward direction of the drone.
The Heading Hold Mode needs to ensure that the front of the drone
is consistent with the front of the controller, the controller does not
change the direction of the transmitter, and the
drone is always in front of the controller.
When the front of the drone is not consistent
with the pilot's front, the drone will lose
control or be lost.
Start: press the "Heading Hold Mode" button, the
transmitter will sound "didi" to enter the
Heading Hold Mode.
Off: press again, the transmitter will sound
"dididi" to exit the Heading Hold Mode.
9

Only calibrate when motorboat mode
Flying Trimmer
Left and right side flying trimmer
During the flight, if the drone tilts to left, then press down the left stick in the center
button and push the right stick to right to adjust. Otherwise push to left.
Forward / Backward Trimmer
Press down
During the flight, if the drone tilts forward,
press down the left stick in the center button,
and push the right stick backwards.
Otherwise push forwards.
Left and right turning trimmer
During the flight, if the drone head rotates to
left,then press down the left stick in the
center button and push the left stick to right.
Otherwise push to left.
Drone calibration (When abnormal flying)
Tips: When the drone is fiercely impacted or crashed, it may cause the gyro can
not recover and cause difficult control, if so, you can re-pairing&re-calibrate
and put the drone on the level surface.
Unlocking/locking the motor
After successful frequency alignment,
the right stick is pushed to the lower
right corner by 45°, and the drone LED
turns to keep bright after quick flashing,
indicating that the gyroscope has been
calibrated. Release the right stick.
Push the left and right stick inward to the 45 degree angle simultaneously.
①In standby, unlocked the motor and working.
②In Working, locked the motor and stop rotating.
10

A
B
A=A
B=B
B
A
Note: If the propeller is deformed or damaged, Altitude Hold Mode will fail.
If the atmospheric pressure is instability or Typhoon weather, Altitude Hold
Mode can not work well.
Intelligent flight control system calculates the hovering position, more stable control
feature, makes it easier for beginners to control. Release the stick, the drone will
keep hovering automatically to enable single hand operation.
1. When the propellers get stuck, then activate stuck protection function and the
motors stop running.
2. Pull down the left stick to the lowest position and then go back to the center,
stuck protection will be released and the drone can fly again.
Parts Replacement
Low Battery Alarm
Stuck Protection
Propeller Replacement
Altitude Hold Mode
There is different A and B remarks on the propeller. Be sure that the propellers are
installed to the correct motors, which remarked the Letters to identify on the motor
holder, if not, then the drone can not work normally.
To remove the propeller, hold the propeller vertically and then pull the propeller out.
To install the propeller, mount propeller aim the central shaft of the motor and press
down.
When the transmitter in low battery, the transmitter will continues to sound “di-di” to
remind the user to return home and replace the batteries of thetransmitter as soon
as possible.
When the drone in low battery, the drone LED will continue to "flash and stop ",
the drone must return home at this time.
11

Tips: the above data are the test data of UDIRC toy lab, for reference only.
Parameter
Weitht
Propeller Diameter
Maximum flight time
Operating Temperature Range
Operating frequency
Battery
Type of battery
Charging Time
Charging temperature range
29g（typical value）
38mm
6 minutes(calm)
0°C to 40°C
2.4GHz
3.7V，220mAh
LiPo
About 40 minutes
5°C to 40°C
Drone
Operating frequency
Maximum transmission distance
Operating temperature
Battery
Transmitter
2.4GHz
20m (no interference and barrier-free)
0°C to 40°C
3×1.5V AAA battery
Output
Charger
5V 2A
Attention
①Switching sequence. At first, turn on the power of the drone, then turn on the
power of the transmitter. After the end, turn off the power of the drone first, and
then turn off the power of the transmitter.
Improper operation caused the crash. It is necessary to check and confirm the
connection of the motor，propeller or battery of the drone and the damage
degree, so that the drone can fly again. If there is damaged, please replace the
new accessories or prone to accident.
②
12

Troubleshooting
Drone Battery Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household
trash. Please contact local environmental or waste agency or the
supplier of your model or your nearest Li-Po battery recycling center.
Important Notice
Our company's products are improving all the time, design and specifications are subject to
change without notice.
All the information in this manual has been carefully checked to ensure accuracy, if any
printing errors, our company reserve the final interpretation right.
Problem Problem cause SolutionNO.
1
The controller
Indicator
light is off.
Failed to
pair the
drone with
the
controller.
The drone
is under-
powered or
can not fly.
The drone
could not
hover and
tilts to one
side.
The drone
indicator
light is off.
2
3
4
5
Low battery. Replace the controller battery.
Indicator light is off. The same as above.
There is an interfering signal nearby. Restart the drone and power on the controller.
Mis-operation. Operate the drone step by step in accordance with the user manual.
The electronic component is
damaged for fiercely crash.
To buy spare parts from local seller and
replace damaged parts.
The propeller is seriously deformed. Replace the propeller.
Low battery. Charge the drone battery.
Incorrect installation of propeller. Install the propeller in accordance with the
user manual.
The propeller is seriously. Replace the propeller.
The motor holder is deformed after violent crash. Replace the motor holder parts.
The gyroscope did not reset after
a serious crash.
Put the drone on the flat ground for about 10
minutes or restart the drone to calibrate again.
Low battery. Recharge the drone battery.
Buy a new battery from local seller to replace
the battery or charge the battery.
The battery is expired or over
discharge protection.
The batteries are incorrectly.
The batteries are incorrectly
positioned.
Install the batteries following the polarity indicators.
Clean the dirt between the battery and the
battery contacts.
Motor is damaged. Replace the motor.
13

MADE IN CHINA
FCC Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
●Reorient or relocate the receiving a ntenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
The equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. Modifications not
authorized by the manufacturer may void user’s authority to operate this device.
FCC Notice:
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition with out restriction.
FCC Radiation Exposure Statement
14