UDI R/C U46W User manual

USER
MANUAL
U46W
▲This product is suitable for users over 14 years old.
▲Stay away from the rotating propeller
▲Read the<important statement and safety guidelines >carefully.
Suitable for indoor flight

ON OFF
CHA
Ready Before Take Off
Drone preparation
Charging port
Power Switch
Drone LED Camera
Main frame
Propeller A
Propeller A Propeller B
Propeller B
Front (Prow)
Rear (Tail)
Rear (Tail)
Drone Cover
Housing
2

②①
Charging Instruction
Battery power is insufficient in the original plant. It must be charged
saturated before it can be used.
Connect the original charging cable with the drone, and then connect other USB
charging port. The drone red LED keeps bright when charging and the light turns
green when fully charged. The drone power button should be
turned off when charging.
Original Charging Cable
▲Only use the original charging cable; suggest select Adapters with output current of 5V 2A.
USB adapter
(Not included)
Right Stick
Speedswitch
Heading Hold Mode
Power Switch
Power-LED
Left stick /
Trimmer
(Press down)
No function
Take Off / Landing /
Emergency
Stop Button
Battery installation
Open the battery cover on the back side of the
transmitter ，according to the "+-" electrode
instruction in the battery groove, place the
battery with the same type of saturated power
(battery not include).
Battery cover
Back side of the transmitter
3×1.5V AAA
Alkaline Batteries
Transmitter preparation
3

②
③
①
Flight Operations
Mobile phone connect with Drone
Download and install APP: Flyingsee
This software is suitable for mobile phones
in the IOS and Android system. For detailed
operation, please check the system “HELP”
of APP.
Transmitter connect with Drone
Frequency Pairing
Turn on the power on the
transmitter, the power-LED
will flash quickly.
Horizontal ground
Pull the left stick until bottom and
then release, the transmitter
power-LED will flash slowly, and
enter frequency pairing.
Power on the drone, the
drone LED will change from
flash to keep bright, that
indicates the frequency
pairing is successful.
4

Left stick
Go up
Go down
Right stick
Fly to the left
Fly to the right
Forward
Backward
Control stick operation
Clockwise turn
Counterclockwise
turn
5

Take off
After the frequency pairing is successful, press the "take off/land" button, the
transmitter will sound "di", and the drone will automatically rises and flies at an
altitude of about 1.2 meters.
Tip: Do not use the emergency stop function unless in emergency situation.
Landing
During the flight, press the "take off/land"
button, the transmitter will sound "di",
and the drone will land slowly until landing.
Emergency Stop: During the flight, press
" take off/land" button for about 2 seconds,
the transmitter will sound "di.di..." and the
drone crashes directly.
Don’t operate the left stick during landing,
otherwise the current command will
automatically fail.
Medium speed default
Press the "H/L" button, the transmitter will sound
"di.di.di", to enter High Speed Mode "H".
Press again, the transmitter will sound "di",
to enter Low Speed Mode “L”.
Press again, the transmitter will sound “di.di”,
to enter Middle Speed Mode “M”.
Low speed: suitable for beginners to practice without wind.
Medium speed: suitable for skilled operatoroperating in light breeze.
High speed: suitable for professional operation in outdoor wind resistance.
Speed mode switch
6

Heading Hold Mode
①
②
The default setting is NOT Heading Hold Mode.
Heading Hold Mode means that the user can operate the aircraft without having
to distinguish directions. This mode is suitable for beginners, or when it is
difficult to distinguish the forward and backward direction of the drone.
The Heading Hold Mode needs to ensure that the front of the drone
is consistent with the front of the controller, the controller does not
change the direction of the transmitter, and the drone is
always in front of the controller.
When the front of the drone is not
consistent with the pilot's front, the
drone will lose control or be lost.
Start: Press the "Heading Hold Mode" button,
the transmitter will sound "didi" to enter
the Heading Hold Mode.
Off: Press again, the transmitter will sound "dididi" to exit the Heading Hold Mode.
Front
Rear
7

Flying Trimmer
Press down
Left and right side flying trimmer
During the flight, if the drone tilts to left, then press down the left stick in the
center button and push the right stick to right to adjust. Otherwise push to left.
Forward / Backward Trimmer
During the flight, if the drone tilts forward,
press down the left stick in the center button,
and push the right stick backwards.
Otherwise push forwards.
Left and right turning trimmer
During the flight, if the drone head rotates to
left,then press down the left stick in the
center button and push the left stick to right.
Otherwise push to left.
Drone calibration (When abnormal flying)
Tips: When the drone is fiercely impacted or crashed, it may cause the gyro can
not recover and cause difficult control, if so, you can re-pairing&re-calibrate
and put the drone on the level surface.
After successful frequency alignment,
the right stick is pushed to the lower
right corner by 45°, and the drone LED
turns to keep bright after quick flashing,
indicating that the gyroscope has been
calibrated. Release the right stick.
Unlocking/locking the motor
Push the left and right stick inward to the
45 degree angle simultaneously.
①In standby, unlocked the motor and
working.
②In Working, locked the motor and stop
rotating.
8

①
②
Note: If the propeller is deformed or damaged, Altitude Hold Mode will fail.
If the atmospheric pressure is instability or Typhoon weather, Altitude Hold Mode
can not work well.
Intelligent flight control system calculates the hovering position, more stable
control feature, makes it easier for beginners to control. Release the stick, the
drone will keep hovering automatically to enable single hand operation.
Altitude Hold Mode
Low Battery Alarm
Transmitter:
Drone:
When the transmitter in low battery, the transmitter will continues
to sound “di-di” to remind the user to return home and replace
the batteries of thetransmitter as soon as possible.
When the drone in low battery, the drone LED will continue to
"flash and stop ", the drone must return home at this time.
When the propellers get stuck, then activate stuck protection function and
the motors stop running.
Pull down the left stick to the lowest position and then go back to the
center, stuck protection will be released and the drone can fly again.
Stuck Protection
Out of range alarm
When the drone is out of the remote control distance, the drone LED will
continues to “flash - flash - stop” to alarm the user to return the drone
immediately.
9

There is different A and B remarks on the propeller. Be sure that the propellers are
installed to the correct motors, which remarked the Letters to identify on the motor
holder, if not, then the drone can not work normally.
Disassembly: hold the propeller vertically and then pull the propeller out.
Installation: mount propeller aim the central shaft of the motor and press down.
Disassembly Installation
Parts Replacement
Propeller Replacement
Please make sure the propeller
are installed correctly,
otherwise the drone cannot fly.
B
B
B
A
A
A
Attention
①Switching sequence. At first, turn on the power of the transmitter, then turn
on the power of the drone. After the end, turn off the power of the drone
first, and then turn off the power of the transmitter.
Improper operation caused the crash. It is necessary to check and confirm
the connection of the motor，propeller or battery of the drone and the
damage degree, so that the drone can fly again. If there is damaged, please
replace the new accessories or prone to accident.
②
10