UDI R/C Swan U42 User manual

* Press the Heading Mode button. The drone’s LED lights will
flash alternatively, indicating that the drone has entered
Heading Mode. To turn off Heading Mode, press the
Heading Mode button again.
The drone’s LED lights turn solid,
indicating that Heading Mode is off.
Heading Hold Mode
Download and Install the APP: Flyingsee
The APP is applicable for mobile phone with iOS and Android system, please
download from the mobile phone software store:
1. For Apple device with iOS system, please search Flyingsee in App Store.
2. For Android device with Android system,
please search Flyingsee in Google Play.
3. Scan the QR code on the right or the QR
code in the box to download Flyingsee.
To know your APP
Low Battery Alarm
When the controller batteries are low, the controller will beep with “di...di..di..”
Land the drone and replace the batteries as soon as possible. Or the drone may
be out of control.
When the drone batteries are low, the controller will beep with “di.di.di......” Land
the drone as soon as possible.
Out of Range Alarm
When the drone is about to fly out of the maximum remote control distance, the
controller will beep with “didi...didi...didi”. Fly back into range immediately .
The drone will be difficult or impossible to control when it is out of range.
Motors Stuck Protection
1. When the propellers get stuck, the drone LED will flash quickly and activate
stuck protection function and the motors will stop running.
2. Pull down the Left Stick to the lowest position . The drone LED becomes solid
and stuck protection will be released , and the drone can fly again.
15
www.udirc.com

Using the Flyingsee APP
Pairing your device with the drone
2. Enter your device’s set up screen, turn on Wi-Fi (WLAN) and choose udirc-***,
Return to main screen after successful connection.
1. Install the Li-po battery into the drone and power on the drone. Put the drone
on a flat surface in a horizontal position. ( Very Important)
3. 4.
Go to UIDRC official website for more information about our products.
Download the manual and learn how to fly the drone properly.
1
2
Help & Tips.
View your photos or videos.
4
5
Tap this icon to
open the APP.
Flyingsee
Learn the operation
of drone
Remote control interface
Media
Help
Explore UDIRC Drone
HOME
1
2
3
45
Select to enter
the remote control interface
for real time transmission.
3
16
www.udirc.com

Introduction to the APP Icons
Home Page Icon
Tap to go back to the Home Page.
Tap this icon to enter Virtual Reality Mode to
experience first person view ( only available
when using a VR headset). Tap again to exit
from Virtual Reality Mode.
Virtual Reality Mode
Tap this icon to enter Flight Route Setting Mode.
Draw a flight route in the right area. The drone
will fly according to the flight route. Tap again
to exit from this mode.
Flight Route Setting Mode
image image
Virtual Control Interface
Select to enter the remote control interface for real time transmission.
Learn all the APP
icons first
3
pop-up window.
Enter to the virtual remote interface,
the drone body LED lights change
from flashing to solid, indicating
that the paring is successful and
the drone is ready for fly.
Frequency Pairing
Real time Transmission Interface
Tap the icon in
17
www.udirc.com

The icon is red by default. Tap this icon and the propellers will stop immediately.
The drone will fall straight to the ground. Do not use the EMERGENCY function
except in an emergency.
EMERGENCY EMERGENCY
To show the strength of WiFi signal of the drone.
Remote Control Signal
When TF card has not been inserted to the drone camera, then the icon will show
, when the TF card is in, then the icon shows .
TF Card Icon
Tap this icon to set parameters. Tap again to exit.
Tap “Save” to save trimmer setting.
Tap”Reset” for factory reset.
Select the picture transmission resolution.
Setting
SETTING
Trimming Save Reset
Transmission quality 720P 480P
The choice of Remote Control Mode
Remote Control
The virtual remote controller is hidden by default. Tap the icon to display
the virtual remote controller.
Tap this icon to enter Gravity Induction Mode. Tilt the phone to fly left / right
and forward / backward. Tap again to exit from Gravity Induction Mode.
Gravity Induction Mode
If the mobile phone tilts to the left / right, the Right Ball will
move accordingly enabling the drone to fly left / right.
18
www.udirc.com

H:0.1m
Tap this icon, the drone will fly down slowly and land on the ground.
All propellers will stop.
The real time flying altitude(Based on the calibration altitude)
One Button Landing
Flying Altitude
Click on this icon and it turns red shortly. The drone will fly up automatically and
stay flying at an altitude of 1.2 meters.
One Button Take Off
Tap to view or delete the aerial video and photo. Tap the Home Page icon to exit.
Access Media
By default , the drone is in Low Speed. Tap “H” to enter High Speed Mode.
High / Low Speed Mode
Tap to take a photo.
Take Photo
Tap and it turns red, indicating that the drones has entered Heading Hold Mode.
Tap again to exit from Heading Hold Mode. The icon turns white.
Heading Hold Mode
Tap to record video. The recording time will display at the
bottom of the screen. Tap again to stop recording.
Record Video
If the mobile phone tilts to forward / backward, the Right Ball will
roll forward / backward enabling the drone to fly forward / backward.
19
www.udirc.com

100%
When the drone battery capacity left around 15%, the phone will vibrate to alarm
that the battery is going to run out and you need to fly back and replace the
battery as soon as possible.
Drone Battery Level
Take Off
Move the right ball outward 45 degree (Do not touch the left ball). The drone body
light will flash 3 times, and then become solid , indicating calibration is complete
and the drone is ready to be controlled.
Tips: Crashing the drone may cause it to become imbalanced beyond the level
that can be adjusted by the trimmer button. If this occurs, you can do
the connection with Wi-Fi , pairing and calibration.
Move the left ball up slowly, the drone will take off.
Move the left ball and right ball at the same time 45 degrees inward.
( This operation is used for start / lock the motor. When the motor is working, it
could be used to stop the motor urgently.)
APP CALIBRATION
(Do not calibrate before successful frequency pairing)
20
www.udirc.com