Ultravation UVMatrix EZ Series User manual

UVMatrix EZ Series
Air Disinfection Systems
Owners Manual
Safety Precautions:
It is recommended that this unit be installed and
maintained by a trained technician:
WARNING: UV Hazard. Always protect eyes from
ultraviolet light. NEVER look at UV lamps in
operation. Unplug or disconnect power before re-
lamping or servicing.
WARNING: Severe eye damage or temporary
blinding may occur.
WARNING: DO NOT operate outside of Air Handler.
WARNING: No openings in duct are allowed which
would give direct line-of-sight to the UV light.
In the event of accidental breakage or replacement of
the ultraviolet lamp, please ensure that the lamp is
disposed of in accordance with local and state
environmental laws regarding fluorescent lamps
containing mercury.
Notice:
All wiring inside of the duct or air handling system in
direct line of site of the UV lamp must be shielded with
aluminum foil tape or equivalent non-combustible
material. When installing this unit, select a mounting
location that prevents ultraviolet light exposure to
plastic flexible duct liner or other plastic components
with unknown resistance to ultraviolet light. Ultraviolet
light may cause color shift or structural degradation of
plastic HVAC components
DC-IH-0229
Installation Steps for Internal Mounting of
Power Supply:
This unit installs in the tightest spaces such as fan
coil units and PTACs while mounting with high
strength magnets.
1. Place UV lamp and ballast assembly in a
position which will allow the UV lamp to bathe
the entire surface to be treated. Next plug the
lamp connector onto the lamp.
2. Connect power wires to the powered down
HVAC system (with supplied wire nuts). This
should be done in Accordance with all
State and Local Electrical and Building
Codes.
Maintenance:
Note: It is recommended that this unit be installed
and maintained by a trained technician. Never
perform maintenance on the UV unit without
disconnecting power.
Typical maintenance consists of replacement of the
ultraviolet lamps.
UV lamps undergo a photochemical process during
operation. This slowly reduces the amount of UV light
generated to disinfect against airborne pathogens. For
optimum air stream disinfection against airborne
pathogens it is recommended the UV lamps be
changed on an annual basis.
When installing new lamps, ensure that the lamp glass
is free from any fingerprints or debris, as this may alter
the path of the UV energy. Use rubbing alcohol and a
dry cloth to remove any surface contaminants.

Trouble Shooting:
The Ultravation air disinfection equipment is designed
to provide many years of trouble free operation. In the
unlikely event of a problem, please contact your local
dealer or Ultravation directly. Before calling for service,
you should have your Model No., Serial No., and
Manufacturing Date.
If you are Troubleshooting the Unit
Check the Following:
•Verify the unit has power (120-277 volts)
•Lamp is securely plugged in into the socket, no
loose wires, and in the right orientation.
•Verify if in fact the UV lamp is on or off. Do Not
Look at the UV Light Without Proper Eye
Protection.
•If possible try a new lamp in the Unit to see if it
lights.
Warranty:
Ultravation warrants this product against any defects in
the power supply or lamp lead for a period of 10 year
after date of consumer purchase, with the exception of
the Ultraviolet Lamp, which is warranted for a period of 1
year after date of consumer purchase.
This warranty does not include damage to the unit from
accident, misuse or improper installation.
If this product should become defective during the
warranty period, Ultravation will repair or elect to replace
the product free of charge.
Ultravation will return repaired or replaced warranted
products pre-paid, provided that the product was
delivered pre-paid. Ultravation shall have no
responsibilities for charges incurred by the customer for
installation or removal of warranted items. Liability is
limited only to the replacement or repair of this product
This warranty gives you specific legal rights, and you
may also have other rights, which vary from state to
state.
All returns must be accompanied by a return
authorization number, which may be obtained by
contacting Ultravation, Inc.
Ultravation, Inc. ~ P.O. Box 165 ~ 212 Ideal Way ~
Poultney, Vermont 05764
Phone: [phone] ~ Fax: [phone] ~
www.ultravation.com
Replacement Parts:
22” T3 Lamp Assembly AS-IH-1005
33” T3 Lamp Assembly AS-IH-0611
48” T3 Lamp Assembly AS-IH-0612
62” T3 Lamp Assembly AS-IH-0610

Ultravation, Inc.
212 Ideal Way
Poultney, Vermont 05764
Ph: 802-287-9735
Fx: 802-287-9203
www.Ultravation.com
Description:
Part #: Drawing #: Rev -B
Date: Scale: Creator:
Models & Specifications
JSM
1/20/20
UVMatrix-EZ Series UVMatrixEZS-DSS
Model Number
T3 UVC Lamp
(X)"
UVMatrix EZ with T3 UVC Lamp (lamp
length option above (X)). 6' Lamp lead,
120-277v Operation. *Optional, full length
light shield and magnet mount*.
6' Quick connect lamp
lead
4 Pin Lamp
Connector
*Optional magnet mounting
(2 magnets and mounting
screws required)
Part Number: 94-068 includes
1 magnet and 1 screw.
*Optional Light
Shield Accessory -
See chart above for
corresponding part
number
2- T3MC's Supplied (T3
Lamp Mounting Clip)
Lamp Part Number Lamp Length (X) Power Consumption
29VA22" T3 Lamp
33" T3 Lamp
48" T3 Lamp
AS-IH-1005
AS-IH-0611
AS-IH-0612
UVMatrix EZ-22
UVMatrix EZ-33
UVMatrix EZ-48
62" T3 Lamp
AS-IH-0610
UVMatrix EZ-62
Light Shield Part Number
94-047
94-045
94-046
94-043
42VA
60VA
76VA
17VA12" T3 Lamp
17" T3 Lamp
AS-IH-1001
AS-IH-1003
UVMatrix EZ-12
UVMatrix EZ-17
94-050
94-049 22VA
Ultravation Auto Sensing
120-277v Electronic Power
Supply
978"
1 14"
1 58"