Unfinished Furniture of Wilmington HAMPTON TV-25 User manual

ITEM NO.: TV-25
REVISED MAY 16, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No
: HAMPTON 44 IN X-SIDE TV STAND
: TV-25

ITEM NO.: TV-25
REVISED MAY 16, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDE

ITEM NO.: TV-25
REVISED MAY 16, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
F
Back panel
1
B
Side frame
(L-R)
2
G
Drawer bottom
2
C
Center
panel
1
H
Drawer side
(L-R)
4
D
Bottom
frame
1
I
Drawer back
2
E
Vertical
frame
1
L
Drawer front
2
M
Support
bar
2

ITEM NO.: TV-25
REVISED MAY 16, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm)
16
2
Spring washer
(6.5 x11mm)
14
3
Flat washer
(6.5 x 19mm)
14
4
Allen key
(M4 x 30mm x 120mm)
1
5
Screw
(M4 x 30mm)
28
6
Pan head screw
*Metal knob: (M4 x 22mm)
*Wooden knob: (M4 x 25mm)
2
7
Wooden knob
2
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
2
STEP 1
Attach vertical frame (E) to bottom frame (D) and center panel (C) with bolts (1), and washers (2)
and (3) as shown below. Tighten with Allen key (4).
Then slide back panel (F) into the grooves of bottom frame (D) and center panel (C) as shown below.

ITEM NO.: TV-25
REVISED MAY 16, 2016
Printed in Vietnam
- 5 -
Attach side frames (B) to center panel (C) and bottom frame (D) with bolts (1), and washers (2) and
(3) as shown below. Tighten with Allen key (4).
Attach top (A) to side frames (B) with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (4).
STEP 2
STEP 3

ITEM NO.: TV-25
REVISED MAY 16, 2016
Printed in Vietnam
- 6 -
Attach drawer sides (H) to drawer front (L) with screws (5) as shown below. Tighten with a screwdriver.
Slide drawer bottom (G) into the grooves of drawer sides (H) and drawer front (L). Then attach the
drawer back (I) to drawer sides (H) with screws (5) as shown below. Tighten with a screwdriver.
Attach support bars (M) to bottom of drawers with screws (5) as shown below. Tighten with a
screwdriver.
STEP 4
STEP 5

ITEM NO.: TV-25
REVISED MAY 16, 2016
Printed in Vietnam
- 7 -
Attach knobs (7) to front of drawers with pan head screws (6) as shown below. Tighten with a
screwdriver.
STEP 6