Unfinished Furniture of Wilmington MISSION BJ6TD User manual

ITEM NO.: BJ6TD
REVISED JUN 01, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:MISSIONENDTABLE
: BJ6TD

ITEM NO.: BJ6TD
REVISED JUN 01, 2015
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: BJ6TD
REVISED JUN 01, 2015
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Table top 1 B Back panel 1
C Side frame
(L-R)
2
D Bottom shelf 1
E Drawer
front panel 1
F Drawer back
panel 1
G
Drawer
side panel
(L-R)
2
H Drawer bottom
panel 1
I Back
crossbar 1
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following parts:
NO Description Qty Sketch NO Description Qty Sketch
1 Short bolt
(M6x35mm) 8
2 Spring washer
(6.5x11mm) 8
3 Flat washer
(6.5x19mm) 8
4 Screw
(M4x30mm) 8
5 Short screw
(M4x15mm) 14
6
Pan head
screw
(M4x30mm)
1
7 Knob
(38x30mm) 1
8 Allen key
(M4x80mm) 1

ITEM NO.: BJ6TD
REVISED JUN 01, 2015
Printed in Vietnam
- 4 -
STEP 1
Attach side frame (C) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (8).

ITEM NO.: BJ6TD
REVISED JUN 01, 2015
Printed in Vietnam
- 5 -
STEP 2
Insert back crossbar (I) Into side frames (C ) as shown below.
Attach side frames (C) to top (A) and bottom shelf (D) with bolts (1), and washers (2) and (3) as
shown below. Tighten with Allen key (8).

ITEM NO.: BJ6TD
REVISED JUN 01, 2015
Printed in Vietnam
- 6 -
STEP 3
Attach back panel (B) to the unit with screws (5) as shown below. Tighten with a screwdriver.
STEP 4
Attach panels (H), (E), (F) and (G) together with screws (4) as shown below. Tighten with a
screwdriver.
Attach knob (7) to drawer front (E) with screw (6). Tighten with a screwdriver.

ITEM NO.: BJ6TD
REVISED JUN 01, 2015
Printed in Vietnam
- 7 -
STEP 5
Insert drawer into the unit as shown below.