Unfinished Furniture of Wilmington TV-31 User manual

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 48 IN MISSION TV STAND
: TV-31

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish on your product. Protect the surface of the product with a cloth if you are using any
product with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
TOP
1
B
VERTICAL
PANEL
1
C
BOTTOM
PANEL
1
D
SHELF
2
E
SIDE
FRAME
(L&R)
2
F
BACK PANEL
1
G
VERTICAL
FRAME
1
H
BOTTOM
FRAME
1
I
DRAWER
FRONT
(L&R)
2
J
DRAWER
BACK
2
K
DRAWER
SIDE PANEL
(L&R)
4
L
DRAWER
BOTTOM
2

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Long bolt
(M6x50mm)
2
2
Medium bolt
(M6x35mm)
16
3
Large flat
washer
(ɸ6.5x16mm)
10
4
Spring washer
(ɸ6.5x11 mm)
18
5
Medium screw
(M4x30mm)
17
6
Short screw
(M3.5x15mm)
10
7
Shelf support
bracket
8
8
Pan head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
2
9
Wooden knob
2
10
Warning label
2
11
Allen key
(M4x80mm)
1
12
Steel band
1
13
Small flat
washer
(ɸ6.5x13mm)
8
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
2

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 5 -
Attach Vertical panel (B) to the Top (A) with bolts (2) and washers (3) and (4), as shown below.
Tighten with Allen key (11).
STEP 2
Attach Bottom panel (C), Vertical frame (G) to the unit (from Step 1) with bolts (1) and washers (4)
and (13) as shown below. Tighten with Allen key (11) .
STEP 1

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 6 -
Attach Bottom frame (H) to the unit (from Step 2) with bolts (2) and washers (4) and (13) as shown
below. Tighten with Allen key (11).
STEP 4
Attach Side frame (E) to the Top (A) and Vertical frame (G) with bolts (2) and washers (3), and (4), as
shown below. Tighten with Allen key (11).
Attach Side frame (E) to Bottom frame (H) with bolts (2) and washers (13), and (4), as shown below.
Tighten with Allen key (11).
STEP 3

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 7 -
Slide the back panel (F) into the grooves as shown below.
Attach Side frame (E) to the unit with bolts (2), and washers (4) and (13), as shown below. Tighten with
Allen key (11).
Attach Side frame (E) to the unit with bolts (2), and washers (4) and (3), as shown below. Tighten with
Allen key (11).
STEP 6
Attach drawer sides (K) to drawer front (I) with screws (5) as shown below. Tighten with a screwdriver.
Slide drawer bottom (L) into grooves of drawer sides (K) and drawer fronts (I) as shown below.
Attach drawer back (J) to the drawer sides (K) with screws (5) as shown below. Tighten with a screwdriver.
STEP 5

ITEM NO.: TV-31
REVISED FEB 03, 2016
Printed in Vietnam
- 8 -
STEP 7
Attach the knobs (9) to front of drawers with pan head screws (8) as shown below. Tighten with a
screwdriver.
STEP 8
Stick warning labels (10) on the back side of drawers before use.
Attach brackets (7) to the unit as shown below. Then place shelves (D) on the brackets, and attach
with screws (6). Tighten with a screwdriver.
Attach steel band (12) to the unit with screws (6). Then attach the steel band to a wall with screw (5)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.