Unfinished Furniture of Wilmington OT-3073 User manual

ITEM NO.: 3073
ISSUED DEC 14, 2017
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:SHAKER PLANT STAND 15 X 15 X 24H
: OT-3073

ITEM NO.: 3073
ISSUED DEC 14, 2017
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product
with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: 3073
ISSUED DEC 14, 2017
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Apron
(Short)
2
C
Apron
(Long)
2
D
Shelf
1
E
Leg
(L-R)
4
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm)
8
2
Flat Washer
(6.5 x 16mm)
8
3
Lock Washer
(6.5 x 11mm)
8
4
Long Screw
(M4 x 35mm)
8
5
Short Screw
(M3.5 x 15mm)
8
6
L-Bracket
4
7
Allen key
(M4 x 30mm x 110mm)
1

ITEM NO.: 3073
ISSUED DEC 14, 2017
Printed in Vietnam
- 4 -
STEP 1
Attach aprons (C) to the legs (E) with bolts (1), and washers (3) and (2) as shown below. Tighten with
Allen key (7).
STEP 2
Attach aprons (B) to the top (A) as shown below. Then attach legs (E) to aprons (B) with bolts (1), and
washers (3) and (2) as shown below. Tighten with Allen key (7).

ITEM NO.: 3073
ISSUED DEC 14, 2017
Printed in Vietnam
- 5 -
STEP 3
Insert shelf (D) into legs (E) as shown below. Then attach aprons (B) to legs (E) with bolts (1), and
washers (3) and (2) as shown below. Tighten with Allen key (7).
STEP 4
Attach aprons (B) and (C) to top (A) with screws (4) as shown below. Tighten with a screwdriver.
Attach L-bracket (6) to legs (E) and shelf (D) with screws (5) as shown below. Tighten with a screwdriver.