Unfinished Furniture of Wilmington T-17B User manual

ITEM : T-17B AND T-48RT OR T-52T OR T-60RT
(PACKED IN SEPARATE BOX)
REVISED DEC 06, 2014
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: JAVA PEDESTAL
: T-17B AND T-48RT OR T-52T OR T-60RT
(PACKED IN SEPARATE BOX)

ITEM : T-17B AND T-48RT OR T-52T OR T-60RT
(PACKED IN SEPARATE BOX)
REVISED DEC 06, 2014
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
PART LIST T-
4
8RT OR T-52T OR T-60RT
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch N
ODescription Qty Sketch
A Top 1
A
PART LIST T-17B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
B
Pedestal
column 1 C Leg
4

ITEM : T-17B AND T-48RT OR T-52T OR T-60RT
(PACKED IN SEPARATE BOX)
REVISED DEC 06, 2014
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following parts:
NO Description Qty Sketch NO Description Qty Sketch
1 Flat washer
(8.5x19mm) 8
2 Lock washer
(8.5x13mm) 12
3 Hexagon nut
(M8x13mm) 12
4 Wrench
(13mm) 1
5
Allen key
(4x80mm) 1
6 Flat washer
(8.5x22mm) 4
NOTE : HARDWARE IS PACKED IN CARTON T-17B
STEP 1
Attach legs (C) to the pedestal ( B) with washers (2) and (3) and nuts (1) as shown below. Tighten with
the wrench (4).

ITEM : T-17B AND T-48RT OR T-52T OR T-60RT
(PACKED IN SEPARATE BOX)
REVISED DEC 06, 2014
Printed in Vietnam
- 4 -
STEP 2
Use the Allen key (5) to loosen the bolts and washers, and take off the plate underneath the table
top.
STEP 3
Place the plate on top of the pedestal (B), attach with washers (6) and (2) and nuts (3) as shown
below. Tighten with the Wrench (4).

ITEM : T-17B AND T-48RT OR T-52T OR T-60RT
(PACKED IN SEPARATE BOX)
REVISED DEC 06, 2014
Printed in Vietnam
- 5 -
STEP 4
Carefully put the pedestal block on the bottom side of the table top, attach the top to plate with
bolts and washers (from step 2) and tighten with the Allen key (5).