Uniden GSHC1000 Series User manual

For more exciting new products please visit our website:
Australia: www.uniden.com.au
GSHC1000/3000/5000 Series
Guardian Smart Home Control
OWNER’S MANUAl

2
IMPORTANT SAFETY INSTRUCTIONS
When using your equipment, always follow basic safety precautions to reduce
the risk of fire, electric shock and injury to persons, including the following:
•The units are NOT waterproof. DO NOT expose it to rain or moisture (for
the weatherproof IP camera (App Cam 25): DO NOT expose it to excessive
water or moisture).
•DO NOT immerse any of the units in water. Do not use any of the units
near water, e.g., near a bathtub, wash bowl, kitchen sink or laundry tub, in
a wet basement or near a swimming pool.
•To avoid any risk of electric shock from lightning, avoid handling any
electronic devices (except battery powered ones) during an electrical
storm.
•Use only the power cord and/or batteries indicated in this manual. Never
dispose of any batteries in a fire: they may explode. Check with local codes
for possible special disposal instructions.
•Never tug or pull on any power cord: be sure to leave some slack in the
cord when placing your equipment, and always use the plug to unplug cord
from the wall outlet.
•Never leave power cords where they can become crushed, cut, or frayed;
when running power cords, avoid letting them rub against any sharp edges
or lie across any high traffic areas where people might trip over them.
•Do not use the units if the adaptor cords or plugs have been damaged, the
units have been exposed to liquids, or the units have been dropped or is
damaged.
To avoid damage to your equipment, follow these simple precautions:
•Do not drop, puncture or disassemble any part of the equipment. There are
no user-serviceable parts inside.
•Do not expose the equipment to high temperatures, and avoid leaving the
equipment in direct sunlight for more than a few minutes. Heat can damage
the case or electrical parts.
•Do not place heavy items on top of the equipment or expose the equipment
to heavy pressure.
•Remove the power adaptor during long periods between usages.
•Clean only with a dry cloth.
For best results:

3
Failure to follow the instructions in this owner’s manual will void
the warranty. Uniden assumes no liability for damages to property
or injury to persons caused by improper handling or failure to
comply with these safety instructions.
•STRANGULATION HAZARD. Keep the adaptor cords out of the reach of
children.
•WARNING: KEEP OUT OF THE REACH OF CHILDREN. Allow for proper
ventilation when units are in use. Do not cover any of the units with any
object such as a blanket.

4
CONTENTS
Important Safety Instructions ............ ............................................................... 2
Introduction ..... ........................................................................................................ 5
What’s In The Box .....................................................................................................7
Getting to Know Your Devices ........ ................................................................... 8
Gateway ........................................................................................................... 8
Remote Key ......................................................................................................8
Door/Window Sensor ........................................................................................9
Motion/PIR ...................................................................................................... 9
Indoor Siren ............ ......................................................................................10
App Cam 24 ....................................................................................................10
App Cam 25 ....................................................................................................11
App Cam 26 ....................................................................................................12
Setting Up The System ........................................................................................ 13
Download the App .......................................................................................... 13
Install the Gateway/Connect to Internet ......................................................... 13
Set Up Your System .......................................................................................13
Activate The Sensors ..................................................................................... 14
Connect The Indoor Siren ..............................................................................14
Pairing the Cameras .......................................................................................15
Manual Pairing ................................................................................................21
The GUARDIANHOME App ........................................................................ 24
TROUBLESHOOTING ................................................................................... 37
SPECIFICATION ............................................................................................38
WARRANTY .............................................................................................................. 40

5
INTRODUCTION
Thank you for buying Uniden’s Guardian Smart Home Control Kit!
The Guardian Smart Home Control is the smart way of securing your home. It
consists of Gateway, Door/Window Sensors, Indoor Siren, Motion/PIR Sensor,
Remote Key and indoor/outdoor IP Cameras. All the senors/devices/IP
cameras work in conjunction with the Gateway to keep a close watch on your
property and alert you when required.
If any items are missing or damaged, contact your place of purchase
immediately. Never use damaged products!
Need Help? Get answers at our website:
www.uniden.com.au for Australian model.
We offer a range of packages to smarten up your home.
The Starter Kit (GSHC1000): This is the basic kit and includes one Gateway
Hub, three Door/Window Sensors, two Remote Keys and an App Cam 24.
The Outdoor/Indoor Kit (GSHC3000): This kit offers an outdoor IP Camera
(App Cam 25) and an indoor IP Camera (App Cam 24) along with one
Gateway Hub, three Door/Window Sensors, two Remote Keys, one Motion/
PIR Sensor and one Indoor Siren.
The Deluxe Kit (GSHC5000): This luxury kit offers two Pan/Tilt indoor IP
Cameras (App Cam 26) along with one Gateway, five Door/Window Sensors,
two Remote Keys, two Motion/PIR Sensors and one Indoor Siren.
When you buy any of our kits, please refer to the ‘what’s in the box’ section to
ensure that you have all the items listed, for the kit you purchased.

6
In the graphic illustration below, the Gateway Hub, the Indoor Siren, Motion/
PIR Sensor and the App Cam 26 have been set up in the living room. There is
a Door/Window Sensor installed on the kitchen door and an App Cam 24 set
up in the nursery. The Remote Keys have been left in the master bedroom for
easy access and, the App Cam 25 has been installed outside.
Adaptor DC 12V/1A Adaptor DC 5V/1.5A
Battery AA 1.5V x 3
or
Battery AA 1.5V x 4
(not included)
Gateway
Smart wireless central home
control / management center.
Door/Window Sensor
Wireless door/window access
alert sensor.
Indoor SirenAPPCAM26
Wireless portable/wall-
mount alert siren.
Remote
Wireless multi-functional
remote controller.
APPCAM24
Wireless day/night portable
motion alert indoor camera.
Motion PIR
Wireless portable/wall-
mount area motion alert
sensor.
Battery CR2032
Battery CR2032
Wireless day/night portable
motion alert indoor camera
Adaptor DC 5V/1A
Adaptor DC 5V/1.5A
Wireless day/night portable
motion alert outdoor camera.
Adaptor DC 5V/1.5A
APPCAM25
Now, let’s look at a possible scenario of how you could install the Gateway,
various sensors, Indoor Siren and the App Cams, in your home.
You can set up the sensors and the camera based on your convenience. The
illustration below is just to help you get started.

7
WHAT’S IN THE BOX
CONTENTS GSHC1000 GSHC3000 GSHC5000
GATEWAY 1 1 1
REMOTE KEY 2 2 2
MOTION/PIR SENSOR - 1 2
DOOR/WINDOW SENSOR 3 3 5
- 1 1
APPCAM24 1 1 -
APPCAM25 - 1 -
APPCAM26 - - 2
AC Adaptor
Ethernet Cable
Battery
Adhesive Pad
Wall Mount Bracket
Wall Mount Screw
AC Adaptor
Wall Mount Bracket
Wall Mount Screw
Battery
Adhesive Pad
Wall Mount Screw
Battery
AC Adaptor
Ethernet Cable
AC Adaptor
Antenna
Ethernet Cable
Bracket
AC Adaptor
Antenna
Ethernet-to-USB
Cable
Stand
INDOOR SIREN

8
GETTING TO KNOW YOUR DEVICES
Gateway
The Gateway (GSHC-GW) is the head of the Guardian Smart Home Control
system. It connects to the internet via your router to enable you to control and
access your Guardian Smart Home system from your mobile devices.
WAN
RESET
12V 1A
Power LED
Network LED
Speaker
Reset DC12V Port WAN port
Remote Key
The Remote Keys (GSHC-RM)
can be used to arm or disarm the
system, activate camera recording
and set off the Indoor Siren. Arm
Disarm
Record
Panic
LED
In this section, we will take a look at the each of the sensors/devices/IP
cameras included in the Guardian Smart Home Control package.
Button How it Works?
Arm Press to arm the system.
Disarm Press to disarm the system.
Record Press and hold to start camera
recording.
Panic Press and hold to set off Indoor
Siren, and camera recording.

9
Motion/PIR Sensor
The Motion/PIR (GSHC-PIR) Sensor uses the passive infra red technology to
detect movement in a monitored area.
Lens
Button
(Press to open the
battery cover)
Door/Window Sensor
The Door/Window Sensor (GSHC-MD) monitors the entrances to your home.
LED
Battery Cover

10
App Cam 24
MicroSD
Card Slot
Reset
Link
LED
Microphone
PIR
Sensor
Speaker
Light Sensor
Lens LAN
Port Power
The App Cam 24 is an indoor wireless IP Camera that offers day/night on site/
remote live viewing, recording and storage.
Power LED
Indoor Siren
The Indoor Siren (GSHC-SIR) produces a powerful 110db siren and has a
flashing LED light. It is weatherproof and can function on batteries too.
LED

11
App Cam 25
The App Cam 25 is an outdoor, wireless, weatherproof IP Camera that offers
day/night on site/remote live viewing, recording and storage.
Power Cable / Reset Button
USB to RJ-45
RJ45
Antenna
Infrared LEDs
Power LED
PIR Sensor
Link LED
Camera Stand
SMA Connector
MicroSD Card
slot

12
App Cam 26
The App Cam 26 is an indoor, wireless, IP Camera that offers day/night on
site/remote live viewing, recording and storage.
Light Sensor
Infrared LEDs
Microphone
MicroSD Card
Slot
Link LED
Power Input
Antenna
Connector
LAN Port
Reset

13
SETTING UP THE SYSTEM
Please ensure that your Gateway and mobile device is connected to the same
WiFi router for the initial setup.
Step 1: Download the App
Download the Uniden GuardianHome App from the Apple App
Store or Google Play.
Step 2: Install the Gateway/Connect to Internet
1. Connect the Gateway to the WiFi router
using the Ethernet cable (provided).
2. Connect the Gateway to a power outlet
using the AC adaptor (provided).
3. The Gateway announces,”Power On”
and the Power LED on the Gateway
glows blue.
4. The Gateway announces, “Network Connected”, when a connection to the
internet is established, and the Network LED on the Gateway glows green.
Step 3: Set Up Your System
1. Launch the App.
2. Tap to confirm that you have
connected the Ethernet cable.
3. Tap again to confirm that the system
has been powered on.
4. The App looks for the Gateways’ DID
through its connection on the home WiFi.
Name the Gateway. Enter the default
security code (123456) and tap .
(If the App cannot nd the Gateway’s
DID, ensure that the Gateway is powered
on and connected securely to the router.
Ensure that your mobile device is also
connected via WiFi to your router. Enter
the DID manually. The DID is located on
the bottom of the Gateway. It is highly
recommend that you change the default
security code through the Settings screen
(Refer page 31).
5. Tap the Gateway listing to log in. The
Status screen with all of the sensors that
are paierd to the Gateway displays.
Tap again to confirm that the system

14
Step 4: Activate The Sensors
PLEASE NOTE: For your convenience, we have pre-paired the sensors
(Remote Key, Door/Window Sensor, Motion/PIR Sensor) to the Gateway.
Please take off the insulating plastic tag on the sensors to activate them.
Please refer to the images below.
However, if you encounter problems with any of the sensors/devices or if
you purchase additional sensors/devices, please refer to the manual pairing
instructions to pair the relevant sensor to the Gateway (Refer page 17).
Door/Window Sensor Motion/PIR Sensor Remote Key
Step 5: Connect The Indoor Siren
PLEASE NOTE: For your convenience, we have pre-paired the Indoor
Siren to the Gateway.
However, if you encounter problems with the Indoor Siren or if you purchase
an additional Indoor Siren, refer to the manual pairing instructions.
Please connect the Indoor Siren to the power outlet using the supplied AC
adaptor or insert 4 x AA batteries into the battery compartment to power up
the Siren.
OR

15
The App Cam 24 is included in the GSHC1000 (Starter
Kit) and the GSHC 3000 (Outdoor/Indoor Kit) and does
NOT come paired to the Gateway.
1. First connect the camera to the Wi-Fi router via the Ethernet cable
supplied.
2. Power on the camera using the AC adaptor
supplied and wait until both the LEDs glow
steady.
Note: DO NOT begin the APP setup
process until both LEDs glow steady.
3. Launch the GuardianHome App, select the
Gateway, tap in the ‘Status’ screen and tap
to add a new camera to the Gateway.
Tap . The App will now search for the
camera connected to the Wifi Router and pull
in the camera DID.
4. Tap if search didn’t produce any result
and you would like to manually enter DID (15
characters). (DID can be found on the back of
camera).
5. Please name your camera and specify the location where the camera will
be installed. The camera’s default security code is ‘123456’. Tap to
complete pairing the camera to the Gateway.
Tap . The App will now search for the
Step 6: Pairing the Cameras
App Cam 24
Connecting to the Gateway
Follow the steps below to pair the App Cam 24 to the
Gateway.

16
1. First connect the antenna to the
camera. Then connect the camera
to the Wi-Fi router via the Ethernet
cable supplied.
2. Connect the antenna and power
on the camera using the AC adaptor supplied.
After about 45 seconds, the red LED is steady
on and the green LED begins to flash (3-flash/
pause pattern), indicating that the camera is in
Pairing mode. and wait until both the LEDs glow
steady.
3. Launch the ‘Guardian Home’ App, select the
Gateway, tap in the ‘Status’ section and tap
to add new camera to the Gateway.
Tap the App will now search for the camera
connected to the Wifi router and pull in the
camera DID.
4. Tap if search didn’t produce any result and you would like to manually
enter DID (15 characters). (DID can be found on the back of camera).
5. Please name your camera and specify the location where the camera will be
installed. The camera default Security Code is ‘123456’. Tap to complete
pairing the camera to the Gateway.
Tap the App will now search for the camera
The App Cam 25 is included in the GSHC 3000 (Outdoor/
Indoor Kit) and does NOT come paired to the Gateway.
App Cam 25
Connecting to the Gateway
Follow the steps below to pair the App Cam 25 to the
Gateway.

17
The App Cam 26 is included only in the GSHC5000
(Deluxe Kit) and does NOT come paired to the Gateway.
1. First connect the camera to the Wi-Fi router via the
Ethernet cable supplied.
2. Connect the antenna to the camera. You can
attach the camera stand to the camera as
well, but it is not necessary.
3. Connect the camera to power. After about
45 seconds, the camera goes through a pan/
tilt cycle and the green LED begins to flash
(3-flash/pause pattern).
4. Launch the GuardianHome App, select the
Gateway, tap in the ‘Status’ section and
tap to add new camera to the Gateway.
Tap . The App will now search for the
camera connected to the Wifi Router and
pull in the camera DID.
5. Tap if search didn’t produce any result
and you would like to manually enter DID (15
characters). (DID can be found on the back of camera).
6. Please name your camera and specify the location where the camera will
be installed. The camera’s default security code is ‘123456’. Tap to
complete pairing the camera to the Gateway.
Tap
. The App will now search for the
App Cam 26
Connecting to the Gateway
Follow the steps below to pair the App Cam 26 to
the Gateway.

18
1. For camera to work wirelessly with the
Gateway, you will need to add router to App.
Ensuring that the camera is connected to the
router via Ethernet cable, go to Status, tap
Edit on upper right and select Camera Edit
to enter camera info.
2. In camera info section, tap and enter
camera password (default: 123456) to enter
Advanced Settings. In Wi-Fi setting section,
choose the router and enter its password.
Camera will automatically reboot. Now, please
remove the Ethernet cable, and wait until
GREEN LED indicator become steady on. Now, the
camera can operate wirelessly.
Once you have paired the App Cam 24, 25 or
26 you can change the connection from wired
(ethernet cable) to wireless (WiFi) .
Changing the Camera’s Connection from Wired to Wireless

19
Installing the Cameras
1. Hold the mounting plate where
you want to mount it and mark the
location of the screw holes.
2. Use the included screws and
anchors to attach the mounting
plate to the wall.
3. Use the enclosed screws to screw
the camera to the bracket.
App Cam 26
App Cam 24
Camera Brace
1. Hold the base of the camera stand where you
want to mount it and mark the location of the
screw holes.
2. Use the included screws and anchors to attach
the base to the wall or ceiling. You can also
attach the base into a flat surface such as a
tabletop if needed.
3. Before attaching the camera, tug gently on the
stand to make sure it is securely in place.
4. Disconnect power to the camera.
5. Attach the camera to the mounting screw. Set
the mounting post to the correct angle (up to
90° movement). Tighten the circular camera
brace up against the App Cam 24 to secure it
into place.
6. After installation, reconnect power.
1. Hold the base of the camera
stand where you want to mount it and
mark the location of the screw holes.
2. Use the included screws and anchors
to attach the base to the wall or
ceiling. You can also screw the base
into a flat surface such as a tabletop
if needed.
3. Before attaching the camera, tug
gently on the stand to make sure it is
securely in place.
App Cam 25

20
1. For the App Cam 25, attach the camera bracket to the mounting screw.
You can attach the stand to the top or the bottom of the camera as
needed. Tighten it a few turns, then turn the camera to face the direction
you want.
2. Tighten the camera brace up against the App Cam 25 to secure it into
place.
3. Unlock the mounting post by turning the wingnut to the left a few turns.
4. Set the mounting post to the correct angle, then tighten the wingnut until
the post is locked into place.
5. After the App Cam 25 camera is installed, reconnect power.
1
2
4
3
Loosen the
wingnut to
unlock the
mounting
post.
Attach the camera
to the mounting
screw and turn it
to the desired
direction.
Adjust the post to
the correct angle,
then tighten the
wingnut to lock the
post into place.
Tighten the brace against
the camera to
secure it
in place.