Unitech MS910 User manual

Confidential
Unitech Scanner User’s Manual 2011/5/20
1/20
MS910
Pocket Wireless Scanner
Quick Guide

Confidential
Unitech Scanner User’s Manual 2011/5/20
2/20
Overview
First of all, thank you for choosing Unitech’s products. This decoder build-in scanner comes in
one model and supports SPP , HID two modes of wireless communication.
The scanner supports the following bar code symbologies:
* All major 1D barcodes incl.
* GS1 DataBar

Confidential
Unitech Scanner User’s Manual 2011/5/20
3/20
Introduction：
：：
：
Charging the battery：
：：
：
1. Flip open the mini USB port on the scanner.
2. Insert the mini USB connector into the port on the scanner and USB A connector into a USB
port on the host PC.

Confidential
Unitech Scanner User’s Manual 2011/5/20
4/20
Beeper Indication：
：：
：
Type Definition
Single beep Good read
Single long beep Power up
Two beeps Wireless connection
Two short beeps The scanner successfully reads a configuration
barcode
Three short beeps The scanner reads a barcodes while
disconnected
Three beeps Wireless disconnection
Five beeps Low power
10 or 11 short beeps The scanner switches from one communication
mode to another
LED Indication：
：：
：
Type Definition
Off Standby or Power off
Flashing Green Disconnected or Discoverable
Green for 2 sec Good Read
Flashing Red Low power
Solid Red Charging

Confidential
Unitech Scanner User’s Manual 2011/5/20
5/20
Getting connected：
：：
：
I. Window PC
SPP mode
1. Press the trigger for 1 second to activate the scanner.
2. Scan “Disconnect”
3. Scan ”BT Mode - SPP” the scanner will emit 10 beeps.
4. Select “Wireless Scanner” from discovered device list. The default pincode is “1234”.
5. Open serial communication software with com port (see device manager) properly set up.
6. The scanner will beep twice to verify the connection.
HID mode
1. Press the trigger for 1 second to activate the scanner.
2. Scan “Disconnect”
3. Scan ”HID Mode - SPP” the scanner will emit 11 beeps.
4. Select “Wireless Scanner” from discovered device list.
5. The Bluetooth application may prompt you to scan a pincode (see PINCODE SETUP section) it
generated.
6. The scanner will beep twice to verify the connection.

Confidential
Unitech Scanner User’s Manual 2011/5/20
6/20
PinCode Start:
1. When asked by Bluetooth application to enter a pincode
2. Scan [Pincode-Start]
3. Scan the numeric barcodes according to the pincode generated by the Bluetooth application, and
then scan [Enter]
4. Scan [Pincode-Stop]
5. The scanner will beep twice to verify a successful connection.

Confidential
Unitech Scanner User’s Manual 2011/5/20
7/20
II. Windows Mobile
1. Press the trigger for 1 second to activate the scanner.
2. Scan “Disconnect”
3. Scan ”HID Mode - SPP” the scanner will emit 11 beeps.
4. PDA choiceSettingBluetoothWireless Scanner

Confidential
Unitech Scanner User’s Manual 2011/5/20
8/20
5. Input any digit as pincode, e.g.555
6. Scanner need to set pincode within 10 sec. in “Pincode Start” section. (Page 6)

Confidential
Unitech Scanner User’s Manual 2011/5/20
9/20
7. The scanner will beep twice to verify a successful connection.

Confidential
Unitech Scanner User’s Manual 2011/5/20
10/20
III. Android OS
1. Download BluetoothConnect.apk onto your mobile device and install it.
2. Once you enter the BluetoothConnect, the application may ask you to enable Bluetooth
connection, and then click [Yes].
3. Click the Menu button to enable the settings menu.