Unverferth BRENT V1100 User manual
Grain Handling
CORNER-AUGER GRAIN CART
MODEL V1100
Serial Number B36110100 - B42910099
Part Number 290909
Brent V1100 — Introduction
2
Foreword
This symbol identifies important safety messages. When you see it, read the message
that follows and be alert to the possibility of personal injury.
Remember, safety instructions stated in this manual are for your protection. Read them care-
fully and follow them closely when working around or using this machine.
Read and study this manual completely before attempting to operate this implement. Take this
manual to the field for handy reference when operating, adjusting, or servicing your machine.
When referenced, “Right-Hand” (RH) and “Left-Hand” (LH) side of the machine are determined
by standing behind the machine and facing in the direction of travel.
Brent V1100 — Introduction
3
• Theinformation,specifications,andillustrationsinthemanualarebasedoninformationavailable
at the time it was written. Due to continuing improvements in the design and manufacture of
Unverferth products, all specifications and information contained herein are subject to change
without notice.
Product Information
When ordering parts or when requesting further information or assistance, always give the
following information:
• Machine name
• Model
• Serial Number
All products manufactured by Unverferth Mfg. Co., Inc. are warranted to be free from ma-
terial and workmanship
defects for one full year from time of consumer delivery. Your local
dealer will gladly assist you with any warranty questions.
Please fill out and retain this portion for your records. The serial number plate is located
on the frame as shown below.
Purchase Date _____________Model _________________Serial Number______________________________
Dealer ____________________________________ City ____________________________________________
Dealer Contact _______________________________ Phone ______________________________________
Serial Number Location
Brent V1100 — Introduction
4
Table of Contents
Section I
Safety
General Hazard Information............................................................................................................ 1-2
Safety Decals.................................................................................................................................. 1-3
Following Safety Instructions.......................................................................................................... 1-5
Before Operating............................................................................................................................. 1-5
Before Servicing.............................................................................................................................. 1-6
During Operation............................................................................................................................. 1-6
Before Transporting......................................................................................................................... 1-7
During Transport.............................................................................................................................. 1-7
Driveline Safety............................................................................................................................... 1-8
Pressurized Oil................................................................................................................................ 1-9
Preparing for Emergencies.............................................................................................................. 1-10
Wearing Protective Equipment........................................................................................................ 1-10
Brent V1100 — Introduction
5
Table of Contents
Section II
Set Up
Set Up Checklist............................................................................................................................. 2-2
Set Up............................................................................................................................................. 2-4
Hydraulic System...................................................................................................................... 2-4
Optional Hydraulic Brake System............................................................................................. 2-4
Wheel/Tire Set Up.................................................................................................................... 2-4
Tire Pressure...................................................................................................................... 2-4
Wheel Nuts........................................................................................................................ 2-4
Auger Rest Retainer Removal.................................................................................................. 2-5
Driveline Storage...................................................................................................................... 2-5
Video System (Optional)........................................................................................................... 2-5
Jack.......................................................................................................................................... 2-6
Driveline Set Up....................................................................................................................... 2-7
Coupling The Cut-Out Clutch................................................................................................... 2-7
Lamp Set Up............................................................................................................................ 2-8
SMV Emblem & SIS Decals..................................................................................................... 2-8
Wheel Axle Spacing.................................................................................................................. 2-9
Adjustable Axle (Optional)......................................................................................................... 2-9
Sideboard and End Caps......................................................................................................... 2-11
Tarp Installation........................................................................................................................ 2-20
Operational Check........................................................................................................................... 2-26
FOR SCALE, TRACK, UHARVEST, HYDRAULIC DRIVE, ELECTRIC TARP, AND VIDEO SYSTEM
OPTIONS, PLEASE REFER TO THE SPECIFIC MANUAL.
Brent V1100 — Introduction
6
Table of Contents
Section III
Operation
Operating Checklist......................................................................................................................... 3-2
Preparing Tractor............................................................................................................................. 3-3
Preparing Cart
Hardware.................................................................................................................................. 3-3
Pivot Pins................................................................................................................................. 3-3
Hitch......................................................................................................................................... 3-3
Auger........................................................................................................................................ 3-3
Auger Driveline Assembly......................................................................................................... 3-3
Hydraulic System...................................................................................................................... 3-5
Optional Hydraulic Brake System............................................................................................. 3-5
Tires/Wheels.............................................................................................................................. 3-5
Lubrication....................................................................................................................................... 3-5
Video System (Optional).................................................................................................................. 3-5
Hitching to Tractor
Drawbar Connection................................................................................................................. 3-6
Jack Usage............................................................................................................................... 3-7
Transport Chain Connection...................................................................................................... 3-8
Hydraulic Connections.............................................................................................................. 3-9
Hydraulic Connections for Hydraulic Drive............................................................................... 3-10
Electrical Connections............................................................................................................... 3-11
Optional Implement Brake Connection..................................................................................... 3-11
Towing............................................................................................................................................. 3-12
Electric Over Hydraulic Operation (Optional).................................................................................. 3-13
Manual Override for Optional Electric Over Hydraulic System...................................................... 3-16
Auger Operation.............................................................................................................................. 3-18
PTO Driven Auger..................................................................................................................... 3-18
Increasing Maximum Flow Door Opening................................................................................ 3-20
Troubleshooting................................................................................................................................ 3-21
Optional Equipment......................................................................................................................... 3-22
Hydraulic Drive......................................................................................................................... 3-22
Weather Guard Tarp........................................................................................................................ 3-24
FOR SCALE, TRACK, UHARVEST, HYDRAULIC DRIVE, ELECTRIC TARP, AND VIDEO SYSTEM
OPTIONS, PLEASE REFER TO THE SPECIFIC MANUAL.
Brent V1100 — Introduction
7
Table of Contents
Section IV
Maintenance
Lubrication....................................................................................................................................... 4-2
Hydraulic System
Purge Hydraulic System - Standard Spout.............................................................................. 4-4
Relieving Hydraulic Pressure.................................................................................................... 4-5
Purging Procedure for EOH System............................................................................................... 4-5
Bleeding Procedure For Braking System (Optional)....................................................................... 4-6
Brake Pressure Manual Release.............................................................................................. 4-7
Gearbox Lubrication........................................................................................................................ 4-8
Seasonal Storage............................................................................................................................ 4-9
Auger System.................................................................................................................................. 4-10
Lower Auger Removal.............................................................................................................. 4-11
Hanger Bearing Centering.................................................................................................. 4-13
Lower Auger Timing........................................................................................................... 4-13
U-Joint Spline Gap............................................................................................................. 4-14
Upper Auger.............................................................................................................................. 4-15
Upper Auger Removal........................................................................................................ 4-15
Soft Start Replacement...................................................................................................... 4-16
Upper Auger Assembly and Timing................................................................................... 4-16
Upper Auger Inset.............................................................................................................. 4-17
Upper Auger Bearing Gap.................................................................................................. 4-19
Auger Flow Door Cylinder Replacement.................................................................................. 4-20
Adjusting Cleanout Door................................................................................................................. 4-23
Verify Telescoping PTO Shaft Length............................................................................................. 4-25
PTO Shaft and Clutch..................................................................................................................... 4-27
Auger Driveline................................................................................................................................ 4-30
Bearings.................................................................................................................................... 4-30
Driveline Replacement.............................................................................................................. 4-30
PTO Quick Disconnect.................................................................................................................... 4-33
Tarp Troubleshooting Inspection & Maintenance............................................................................ 4-34
Wheels, Hub and Disassembly and Assembly................................................................................ 4-35
Electrical System Diagram.............................................................................................................. 4-37
Electric Over Hydraulic (EOH) System Schematic 4 Function (Optional)....................................... 4-39
Electric Over Hydraulic Valve Electric Schmatic 4 Spool (Optional).............................................. 4-45
Hydraulic System Plumbing Diagram.............................................................................................. 4-46
Braking System Schematic (Optional)............................................................................................. 4-47
Wheels and Tires - Wheel Nut Torque Requirements................................................................... 4-48
Wheels and Tires - Tire Pressure.................................................................................................. 4-49
Wheels and Tires - Tire Warranty.................................................................................................. 4-51
Torque Chart - Hardware............................................................................................................... 4-52
Capscrews - Grade 5.............................................................................................................. 4-52
Capscrews - Grade 8.............................................................................................................. 4-53
Torque Chart - Hydraulic Fittings................................................................................................... 4-54
FOR SCALE, TRACK, UHARVEST, HYDRAULIC DRIVE, ELECTRIC TARP, AND VIDEO SYSTEM
OPTIONS, PLEASE REFER TO THE SPECIFIC MANUAL.
Brent V1100 — Introduction
8
Table of Contents
Section V
Parts
Please visit www.unverferth.com/parts/ for the most current parts listing.
Final Assembly........................................................................................................................... 5-2
Rigid Axle (SN B37730100 and Higher) .................................................................................. 5-4
Rigid Axle (SN B37730099 and Lower).................................................................................... 5-5
Adjustable Axle (SN B37730100 and Higher) ......................................................................... 5-6
Adjustable Axle (SN B37730099 and Lower)............................................................................ 5-8
Track Axle Components with 5 Point Scale System (SN B37730100 and Higher)............... 5-10
Track Axle Components with 5 Point Scale System (SN B37730099 and Lower)................ 5-12
Hub & Spindle — Rigid Axle Without Scales & Adjustable Axles......................................... 5-14
Hub & Spindle — Rigid Axle With Scales............................................................................. 5-15
Brake Components (Optional)................................................................................................... 5-16
Single Wheels & Tires............................................................................................................. 5-18
Decals...................................................................................................................................... 5-20
Sideboards................................................................................................................................ 5-22
EOH Valve Assembly Components 4 Spool (Optional)............................................................. 5-24
EOH Tractor Circuit Hydraulic Components (Optional)............................................................. 5-26
EOH Valve Electric Schematic 4 Spool (Optional)................................................................... 5-27
Electrical................................................................................................................................... 5-28
Drive Components.................................................................................................................... 5-30
Upper Auger Components........................................................................................................ 5-32
Lower Auger Components........................................................................................................ 5-34
Cleanout Door Assembly.......................................................................................................... 5-36
Flow Door Seals...................................................................................................................... 5-37
Internal Bracing........................................................................................................................ 5-38
Cylinders................................................................................................................................... 5-39
Touch-Up Paint......................................................................................................................... 5-40
Hydraulics - Beginning with Serial Number B37910100........................................................ 5-42
Hydraulics - Serial Number B37910099 & Lower.................................................................. 5-46
Directional Spout...................................................................................................................... 5-48
PTO Cut Out Clutch Components............................................................................................ 5-51
PTO Assembly Cutout Clutch................................................................................................... 5-52
PTO Assembly Shear-Bolt Clutch............................................................................................. 5-54
PTO Assembly Friction Clutch.................................................................................................. 5-56
Friction Clutch Assembly.......................................................................................................... 5-57
45 Degree Gearbox - With 20 Spline Input Shaft................................................................. 5-58
45 Degree Gearbox - With 6 Spline Input Shaft................................................................... 5-60
Driveline U-Joint Assembly...................................................................................................... 5-61
Weather Guard Tarp................................................................................................................. 5-62
Video System Option............................................................................................................... 5-65
FOR SCALE, TRACK, UHARVEST, HYDRAULIC DRIVE, ELECTRIC TARP, AND VIDEO SYSTEM
OPTIONS, PLEASE REFER TO THE SPECIFIC MANUAL.
Brent V1100 — Safety
1-1
Section I
Safety
General Hazard Information............................................................................................................ 1-2
Safety Decals.................................................................................................................................. 1-3
Following Safety Instructions.......................................................................................................... 1-5
Before Operating............................................................................................................................. 1-5
Before Servicing.............................................................................................................................. 1-6
During Operation............................................................................................................................. 1-6
Before Transporting......................................................................................................................... 1-7
During Transport.............................................................................................................................. 1-7
Driveline Safety............................................................................................................................... 1-8
Pressurized Oil................................................................................................................................ 1-9
Preparing for Emergencies.............................................................................................................. 1-10
Wearing Protective Equipment........................................................................................................ 1-10
Brent V1100 — Safety
1-2
General Hazard Information
No accident-prevention program can be successful without the wholehearted cooperation of
the person who is directly responsible for the operation of the equipment.
A large number of accidents can be prevented only by the operator anticipating the result
before the accident is caused and doing something about it. No power-driven equipment,
whether it be transportation or processing, whether it be on the highway, in the field, or in
the industrial plant, can be safer than the person who is at the controls. If accidents are
to be prevented--and they can be prevented--it will be done by the operators who accept
the full measure of their responsibility.
It is true that the designer, the manufacturer, and the safety engineer can help; and they will
help, but their combined efforts can be wiped out by a single careless act of the operator.
It is said that, “the best kind of a safety device is a careful operator.” We, at Unverferth
Mfg. Co., Inc. ask that you be that kind of operator.
REMEMBER:
THINK SAFETY
A CAREFUL OPERATOR IS THE
BEST INSURANCE AGAINST AN
ACCIDENT!
SIGNAL WORDS
INDICATES AN EXTREMELY HAZARDOUS SITUATION OR ACTION THAT WILL RESULT IN
SERIOUS INJURY OR DEATH.
INDICATES A HAZARDOUS SITUATION OR ACTION THAT COULD RESULT IN SERIOUS IN-
JURY OR DEATH.
INDICATES AN UNSAFE SITUATION OR ACTION THAT MAY RESULT IN PERSONAL INJURY.
Is used for instruction on operating, adjusting, or servicing a machine.
Brent V1100 — Safety
1-3
Safety Decals
9003474
9003475
9003476
95046
94094
97575
97961
9003477
9003478
9003475
95839
95445
TA1-906109-0
94754
9008151
9008151
95008
9003574 - Prior To Serial Number B38140100
9008447
9008715
9008721
DWG. NO.
PLOT DATE:
TITLE
LATEST CN
REV LEVEL
MAT'L
RELEASE
DWG. BY CONTROL
DATE
WEIGHT PAINT SQ
INCHES
0CN08104
REVISION DATE
1/24/2022 - 11:46 AM
0.1 lbmass
SR
CN08104
ryanf
THIS DRAWIN
G
UNVE
R
MANUFACT
U
AND MAY NOT BE REP
R
1/24/2022
1/24/2022 - 11:46 AM
DECAL- CAUTION, V
A
VENDOR: CREATIVE SCREEN PRINT
VENDOR P/N: PER PRINT
AS PURCHASED
FINISH:
SHEET 1 OF 1
ALL DIMENSIONS INCHES UNLESS NOTE D
TOLERANCE
SPECIFIC DIMENSION TOLERANCES ON
DRAWING OVERRIDE TITLE BLOCK
xx = ±.03 xxx=±.010
DECIMAL
FRACTIONAL ANGULAR
± 1°
± 1/16
F
O
L
L
O
W
S
(
M
U
N
S
E
L
L
N
U
M
B
E
R
)
:
9009470
Brent V1100 — Safety
1-4
7
8
6
4
5
12
9
10
19
13
22
13
4
3
17
18
11
Safety Decals (continued)
TA510514
REFLECTORS
9003125 (Fluorescent)
9003126 (Red)
9003127 (Amber) 95046
TA1-906109-0
9008714 9008720
Brent V1100 — Safety
1-5
Following Safety Instructions
• Read and understand this operator’s manual before operating.
• Allmachineryshouldbeoperatedonlybytrainedandauthorizedpersonnel.
• Topreventmachinedamage,useonlyattachmentsandservicepartsapprovedbythemanufac-
turer.
• Alwaysshuttractorengineoffandremovekeybeforeservicing.
• Avoidpersonalattiresuchasloosettingclothing,shoestrings,drawstrings,pantscuffs,longhair,
etc., that may become entangled in moving parts.
• Donotallowanyonetorideontheimplement.Makesureeveryoneisclearbefore
operating machine or towing vehicle.
• Neverattempttooperateimplementunlessyouareinthedriver’sseat.
• Never enter a cart containing grain. Flowing grain traps and suffocates victims in
seconds.
Before Operating
• Donotstandbetweentowingvehicleandimplementduringhitching.
• Alwaysmakecertaineveryoneandeverythingisclearofthemachinebeforebeginning
operation.
• Verifythatallsafetyshieldsareinplaceandproperlysecured.
• Ensurethatallapplicablesafetydecalsareinstalledandlegible.
• Whenworkingaroundtheimplement,becarefulnottobecutbysharpedges.
• Securedrawbarpinwithsafetylatchandlocktractordrawbarinfixedposition.
Brent V1100 — Safety
1-6
During Operation
• Regulatespeedtoeldconditions.Maintaincompletecontrolatalltimes.
• Neverserviceorlubricateequipmentwheninoperation.
• Keepawayfromoverheadpowerlines.Electricalshockcancauseseriousinjury
or death.
• Useextremecarewhenoperatingclosetoditches,fences,oronhillsides.
• Donotleavetowingvehicleunattendedwithenginerunning.
Before Servicing
• Avoid working under an implement; however, if it becomes absolutely unavoidable,
make sure the implement is safely blocked.
• Ensurethatallapplicablesafetydecalsareinstalledandlegible.
• Whenworkingaroundtheimplement,becarefulnottobecutbysharpedges.
• Topreventpersonalinjuryordeath,alwaysensurethattherearepeoplewhoremainoutsidethe
cart to assist the person working inside, and that all safe workplace practices are followed. There
arerestrictedmobilityandlimitedexitpathswhenworkinginsidetheimplement.
• Securedrawbarpinwithsafetylockandlocktractordrawbarinxedposition.
• Explosiveseparationofatireandrimcancauseseriousinjuryordeath.Onlyproperlytrainedper-
sonnel should attempt to service a tire and wheel assembly.
• Addsufficientballasttotractortomaintainsteeringandbrakingcontrolatalltimes.Donotexceed
tractor’s lift capacity or ballast capacity.
Brent V1100 — Safety
1-7
Before Transporting
• Securetransportchainstotowingvehiclebeforetransporting.DONOTtransportwithoutchains.
• Checkforproperfunctionofallavailabletransportlights.Makesurethatallreectorsareclean
andinplaceonmachine.MakesuretheSMVemblemandSISdecalsarevisibletoapproaching
traffic.
• Thisimplementmaynotbeequippedwithbrakes.Ensurethatthetowingvehiclehasadequate
weight and braking capacity to tow this unit.
During Transport
• Complywithalllawsgoverninghighwaysafetywhenmovingmachinery.
• Usetransportlightsasrequiredbyalllawstoadequatelywarnoperatorsofothervehicles.
• Regulatespeedtoroadconditionsandmaintaincompletecontrol.
• Maximumtransportspeedofthisimplementshouldneverexceed20m.p.h.asindicatedonthe
machine.Maximumtransportspeedofanycombinationofimplementsmustnotexceedthelow-
estspeciedspeedoftheimplementsincombination.Donotexceed10m.p.h.duringoff-high-
way travel.
• Slowdownbeforemakingsharpturnstoavoidtipping.Driveslowlyoverroughgroundandside
slopes.
• Donottransportgraincartonroadswhileloaded.
• Itisprobablethatthisimplementistaller,widerandlongerthanthetowingvehicle.Becomeaware
ofandavoidallobstaclesandhazardsinthetravelpathoftheequipment,suchaspowerlines,
ditches, etc.
Brent V1100 — Safety
1-8
Driveline Safety
• Donotallowchildrennearequipmentthatisrunningorengaged.
• Donotexceed1000rpmPTOspeed.
• DisengagethePTO,stopthetractorengine,andremovekeyfromignitionbeforemakinginspec-
tions, or performing maintenance and repairs.
• Inspect the driveline, quick disconnect, overload shear-bolt limiter or clutch, and shielding of-
ten. Repair immediately. Use replacement parts and attaching hardware equivalent to the original
equipment.Onlyalterationsdescribedinthismanualforoveralllength adjustment areallowed.
Any other alteration is prohibited.
• Avoidexcessivelylonghardwareorexposedandprotrudingpartswhichcansnagandcauseen-
tanglement.
• LubricatethedrivelineasrecommendedintheMAINTENANCEsection.
• Keephoses,wiring,ropes,etc.fromdanglingtooclosetothedriveline.
• Installdrivelineandshieldsaccordingtorecommendedlengthsandattachingmethodswithrec-
ommended hardware. The driveline shield should rotate independently a full rotation and tele-
scope freely. The retaining chain must be secured to the implement safety shield.
• AdjustdrawbartoheightandlengthrecommendedinOPERATIONsection.
• Usecautionwhenturningtoavoidcontactbetweentractortiresanddriveline.
• Checkthelengthofthetelescopingmemberstoinsurethedrivelinewillnotbottomoutorsepa-
rate when turning and/or going over rough terrain.
• ProperextendedandcollapsedlengthsofthetelescopingPTOshaftmustbeverifiedbeforefirst
operationwitheachandeverytractor.IftheextendedlengthofthePTOshaftisinsufficient,itmay
become uncoupled or bottom out when turning and/or going over rough terrain which will cause
seriousinjuryordeathfromcontactwithuncontrolledflailingofPTOshaftassemblycomponents.
Brent V1100 — Safety
1-9
Pressurized Oil
• Relievethehydraulicsystemofallpressurebeforeadjustingorservicing.Seehydraulicpower
unit manual for procedure to relieve pressure.
• High-pressureuidscanpenetratetheskinandcauseseriousinjuryordeath.Usecardboardor
wood to detect leaks in the hydraulic system. Seek medical treatment immediately if injured by
high-pressureuids.
• Hydraulicsystemmustbepurgedofairbeforeoperatingtopreventseriousinjuryordeath.
• Donotbendorstrikehigh-pressurelines.Donotinstallbentordamagedtubesorhoses.
• Repairalloilleaks.Leakscancauseres,personalinjury,andenvironmentaldamage.
• Routehosesandlinescarefullytopreventprematurefailureduetokinkingandrubbingagainst
other parts. Make sure that all clamps, guards and shields are installed correctly.
• Checkhydraulichosesandtubescarefully.Replacecomponentsasnecessaryifanyofthefollow-
ing conditions are found:
- Endttingsdamaged,displaced,orleaking.
- Outercoveringchafed/cutorwirereinforcingexposed.
- Outercoveringballooninglocally.
- Evidenceofkinkingorcrushingoftheexiblepartofahose.
Brent V1100 — Safety
1-10
Preparing for Emergencies
Wearing Protective Equipment
• Keeparstaidkitandproperlyratedreextinguishernearby.
• Keepemergencynumbersforfire,rescue,andpoisoncontrolpersonnelnearthephone.
• Wearclothingandpersonalprotectiveequipmentappropriateforthejob.
• Wearsteel-toedshoeswhenoperating.
• Wearhearingprotectionwhenexposedtoloudnoises.
• Donotwearadditionalhearingimpairingdevicessuchasradioheadphones,etc.
Brent V1100 — Set Up
2-1
Section II
Set Up
Set Up Checklist............................................................................................................................. 2-2
Set Up............................................................................................................................................. 2-4
Hydraulic System...................................................................................................................... 2-4
Optional Hydraulic Brake System............................................................................................. 2-4
Wheel/Tire Set Up.................................................................................................................... 2-4
Tire Pressure...................................................................................................................... 2-4
Wheel Nuts........................................................................................................................ 2-4
Auger Rest Retainer Removal.................................................................................................. 2-5
Driveline Storage...................................................................................................................... 2-5
Video System (Optional)........................................................................................................... 2-5
Jack.......................................................................................................................................... 2-6
Driveline Set Up....................................................................................................................... 2-7
Coupling The Cut-Out Clutch................................................................................................... 2-7
Lamp Set Up............................................................................................................................ 2-8
SMV Emblem & SIS Decals..................................................................................................... 2-8
Wheel Axle Spacing.................................................................................................................. 2-9
Adjustable Axle (Optional)......................................................................................................... 2-9
Sideboard and End Caps......................................................................................................... 2-11
Tarp Installation........................................................................................................................ 2-20
Operational Check........................................................................................................................... 2-26
FOR SCALE, TRACK, UHARVEST, HYDRAULIC DRIVE, ELECTRIC TARP, AND VIDEO SYSTEM
OPTIONS, PLEASE REFER TO THE SPECIFIC MANUAL.
Brent V1100 — Set Up
2-2
Set Up Checklist
After the cart has been completely assembled, use the following checklist and inspect the
cart. Check off each item as it is found satisfactory or after proper adjustment is made.
Wash the unit and remove road salt tag #255000 from ladder.
Complete sideboard and tarp set up. Remove tarp/sideboard shipping brackets.
SetorCalibratetractorPTOcontrolengagementtoMINIMUMsetting.Refertotractoroperator’s
manual for setting information.
Remove auger rest retainer.
Adjustaxlefromshippingpositiontodesiredoperatingposition.(Ifapplicable)Referto"Adjusting
Axle(Optional)".
TorquewheelnutsasspeciedinMAINTENANCEsection.
Inatetirestospeciedairpressure.(ifapplicable)
Ensureoptionalhydraulicbrakesarebledandfunctionproperly.(Ifapplicable)
VerifyTrackhasbeenalignedandisproperlyconditioned.(Ifapplicable)
Lubricateallgreasettingsandcheckgearboxoillevel.
Inspect cleanout door assembly for play or movement, refer to “Adjusting Cleanout Door” in the
MAINTENANCE section.
Verifyallsafetydecalsarecorrectlylocatedandlegible.Replaceifdamaged.
Verifyallreectivedecalsarecorrectlylocated.
CheckSMVdecalandSISdecalsareinplace,cleanandvisible.
Verifytransportlightsareworkingproperly.
CheckDrivelineAssemblyphasing.See“AugerDrivelineReplacement”inMAINTENANCEsection.
VerifyPTOlength,see“VerifyTelescopingPTOShaftLength”inMAINTENANCEsection.
Ensuresafetyscreensoveraugerareinplaceandproperlysecured.
Paint all parts scratched in shipment.
Testruntheaugers.See“AugerOperation”inOPERATIONsection.
Table of contents
Other Unverferth Farm Equipment manuals
Unverferth
Unverferth Killbros 1950 User manual
Unverferth
Unverferth BRENT 678 User manual
Unverferth
Unverferth BLU-JET TrenchMaster User manual
Unverferth
Unverferth CROSS-FOLD ROLLING HARROW 1645 User manual
Unverferth
Unverferth BLU-JET SubTiller II User manual
Unverferth
Unverferth 530 User manual
Unverferth
Unverferth PARKER Seed Chariot 2620 User manual
Unverferth
Unverferth Killbros 1035 User manual
Unverferth
Unverferth PARKER 742 User manual
Unverferth
Unverferth 9250 User manual
Unverferth
Unverferth NutriMax 1400 User manual
Unverferth
Unverferth PARKER 524 User manual
Unverferth
Unverferth PARKER 505 User manual
Unverferth
Unverferth AWS-30 User manual
Unverferth
Unverferth RIPPER-STRIPPER 332 User manual
Unverferth
Unverferth Killbros 200 Series User manual
Unverferth
Unverferth Killbros 1135 User manual
Unverferth
Unverferth CROSS-FOLD ROLLING HARROW 1245 User manual
Unverferth
Unverferth Perfecta 10 User manual
Unverferth
Unverferth MAXIMUS 100 Instruction Manual
