URBAN OUTFITTERS SANNA User manual

Assembly Instructions
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place over heat or Air conditioning vents.
Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You may need to re-tighten all bolts after initial use.
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 1 of 4
SANNA MIRROR
HARDWARE LIST
TOOLS REQUIRED BUT NOT INCLUDED:
Phillips Head Screw Driver
PARTS INCLUDED
(A) Mirror
Quantity: 1pc
(4) Screw
M4 x 35mm
Quantity: 4pcs
(5) Anchor
4 x L40
Quantity:
4pcs
(1) Cam Bolt
Quantity: 5pcs (2) Cam Lock
Quantity: 5pcs
(B) Shelf
Quantity: 1pc
(3) Dowel
M8 X 30mm
Quantity: 4pcs
(C) Wall Bracket
Quantity: 1pc

Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 2 of 4
STEP 1. Lay the Mirror onto a clean smooth surface. Insert Dowels (3) as shown. Screw in Cam Bolts (1) in the positions as
shown.
STEP 2. Align the Shelf (B). Press firmly into place.
A
A
1
3
B
1 3
3
3
3
1
1
1
1
SANNA MIRROR

Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 3 of 4
STEP 3. Insert Cam Locks (2) as shown. Press them into place, You may need to spin them until they seat correctly.
Once seated turn them clockwise with a screwdriver until tight, This will lock the Cam Lock onto the Cam Bolt.
STEP 4. With help place the mirror onto the wall where you want it to hang. Mark on the wall the top center of the mirror with a
pencil. Carefully place the mirror on the floor. Next measure down from the top of the mirror to the hanging bracket on the back
of the mirror. This measurement will be used to locate the Wall Bracket (C) onto the wall. Measure down from your pencil mark
on the wall the same measurement from the back of the mirror. This will be the hanging position of the wall bracket (C). Its best
to use a level to make sure the mirror hangs straight. Hold the Wall Bracket (C) against the wall and mark the screw holes.
This is where you will need to insert anchors. You will need to contact your local hardware store to purchase the correct
anchors for your wall-type. Insert your anchors at the marked locations. Align the Wall Bracket (C) and insert screws. Make
sure the Wall Bracket (C) is aligned like the image below.
2
2
4 wall
C
SANNA MIRROR

4
5
Side view
Mirror
C
C
Assembly Instructions
STEP 5. With help hold the mirror over the Wall Bracket (C) and slide it down into place.
SANNA MIRROR
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 4 of 4