URBAN OUTFITTERS ELENA CONSOLE User manual

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 1 of 7
ELENA CONSOLE
Assembly Instructions
TOOLS REQUIRED BUT NOT INCLUDED:
Phillips head screwdriver
WARNINGS:
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place overheat or air
conditioning vents. Adjust levelers so that the furniture sits flat on
uneven floors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You may need to re-tighten all bolts after initial use.
PARTS INCLUDED (CABINET ONLY)
A)Bottom panel x11
D-R) Right Side Panel x11
G)Cam Bolt x41J)Hinges x44
M)M) Glue X1
B)Top panel x11
D-L) Left Side Panel x11
H)Cam Lock x41
K)) Screws
[3x12mm] x24
C-R))Door Panel x11
E)Back Panel x11
I) Dowel x8
L)Long Screws
[4x40mm] x4
C-L) Door Panel x11
F)Cabinet Door Stop x11
71.5 cm
45.7 cm
152.4 cm

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 2 of 7
STEP 11
Lay down all the parts on the clean carpet or cardboard for assembly. Put a small amount of Glue (M) in the
larger pre-drilled holes in Bottom & Top Panels((A&B). Insert Dowels (I))and the Cabinet Door Stop (F) into the
holes in Bottom Panel & Top Panels (A&B) as shown. Screw the Cam bolts (G))into the Top panel (B) as shown.
Insert the Hinges (J) cups into the holes on both door panels (C-R))& (C-L). Insert the screws (K) and partially
tighten with a Phillips head screwdriver (not provided).
STEP 2
Place the Side panels(D-R) & (D-L) on the Dowels (G) in the Bottom wood panel (A). Insert Screws (L) through
the Bottom panel (A) and tighten with a Phillips head screw driver not provided).
ELENA CONSOLE
Assembly Instructions

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 3 of 7
STEP 3
Slide the Back Panel (E) into the grooves in the Side panels (D-R), (D-L)) & the Bottom Panel (A).
STEP 4
Place the Top panel (B) onto the Side panels ((D-R) & (D-L). Ensure the Cam-bolts (G))and Dowels (I))are aligned
with the pre-drilled holes in the edges of the Side panels (D-R) & (D-L). Insert the Cam locks (H) into the holes in
the Side panels (D-R) & (D-L).Use a Phillips head screw driver (not provided) to secure the Cam locks (H).
ELENA CONSOLE
Assembly Instructions

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 4 of 7
STEP 5
Align the Door Panels (C) to the assembled case as shown. Insert the Screws (K) as shown and
tighten with a Phillips head screwdriver. Open and close the door to make sure the hinges operate smoothly
and are placed correctly. Loosen the screws to adjust the door height if needed, re-fasten after adjusting.
ELENA CONSOLE
Assembly Instructions

ELENA CONSOLE
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 5 of 7
PARTS INCLUDED:
A) Bottom Base
x1
E) Glass
x1
I) Adjustable Levelers
x4
B) Top Base
x1
F) Plastic glass pad
x6
J) Hex Key
x4
C) Post
x4
G) Screw
[M6x10mm] x16
D) Case x1
H) Bolt
[M6xL15mm] x4

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 6 of 7
STEP 6
Lay down all the parts on a clean carpet or piece of cardboard for assembly. Insert adjustable levelers (I) into
the Bottom Base (A). Place the Posts (C) on the Bottom base (A).Insert screws (G) as shown and tighten
with the Allen Key (J).
STEP 7
Place the Case (D) onto the partially assembled base between the Posts (C). Insert the Bolts(H) through the
Bottom base (A) into the Case (D) as shown. Partially tighten all of the screws (G) and then tighten completely.
ELENA CONSOLE
Assembly Instructions

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 7 of 7
STEP 8
Place the remaining Posts (C) onto the Top Base (B). Insert Screws(G) as shown and tighten with the Allen Key
(J). Place the newly assembled half of the base onto the other half of the base attached to the Case (D). Insert the
Screws (G) as shown and tighten with the Allen Key (J). Flip the assembly upright and Place the Plastic glass pads
(F) on the top of the base, and then place the Glass top (E) to complete the assembly.
ELENA CONSOLE
Assembly Instructions