urmet domus 1082/80 User manual

sec.4c
−−−−
1
2GO! - Technical manual
ACCESSORIES
SECTION 4C
SPECIAL DECODING Ref. 1082/80 2
SPECIFICATION...............................................................................2
TECHNICAL SPECIFICATIONS........................................................ 2
DEFAULT CONFIGURATION ...........................................................2
INSTALLATION ................................................................................2
PROGRAMMING..............................................................................3
Switching mode............................................................................3
Operating mode............................................................................3
CONFIGURATION AND OPERATION SUMMARY TABLE...............7
WIRELESS CALL REPEATER Ref. 4311/13 8
TECHNICAL FEAUTURES................................................................8
INSTALLATION ................................................................................8
Wiring diagram .............................................................................8
VIDEO MEMORY MODULE Ref. 1082/88 9
TECHNICAL FEAUTURES................................................................9
INSTALLATION ................................................................................9
Description of terminals..............................................................10
OPERATION ...................................................................................10
Recording films...........................................................................10
Film playback .............................................................................10
Download from www.urmetdomus.com Technical Manuals area.
SECTION CONTENTS
Some products may be described in the “New” section.§
GPRS MODEM Ref. 1082/52 11
PROGRAMMING THE MMS MESSAGING PARAMETERS ...........11
PROGRAMMING THE ACCESS PASSWORD
AND MMS MESSAGING NUMBER (TEL1).....................................11
PROGRAMMING THE MODEM CONNECTION
PARAMETERS FOR CONNECTING
TO THE CELL PHONE NETWORK................................................. 11
MMS Messaging activation............................................................11
SUPPLEMENTARY THREE-TONE RINGING Ref. 1072/59 12
4+N INTERFACE FOR 2GO! Ref. 1082/67 12
SPECIFICATIONS...........................................................................12
INSTALLATION............................................................................... 13
Description of terminals..............................................................13
PROGRAMMING............................................................................13
Line terminal settings .................................................................13
CONFIGURATION ..........................................................................13
User code ...................................................................................13
Indoor station code ....................................................................13

ACCESSORIES
2
−−−−
sec.4c 2GO! - Technical manual
TECHNICAL SPECIFICATIONS
Temperature: -5°C +45°C
C, NC, NA exchange contact: 30Vdc 5A
250Vac 5A
Monostable relay activation time: adjustable from 1 second
from 10 minutes ±5%
DEFAULT CONFIGURATION
The special decoder default settings are:
PE dip switch: all ON
INF dip switch: all OFF (INF=0)
SUP dip switch: all ON (SUP=31)
M/T dip switch: OFF (monostable)
COD dip switch: OFF (operation not following calls)
programmed event: staircase lights button
Timer: 1”
Line terminal: ON
INSTALLATION
The special decoder must be considered in the total apartment
station count. Therefore, the number of apartment stations (video
door phones + door phones + PABX interfaces + special decoders)
MUST NOT exceed 32. Up to 4 special decoders can be installed in
the entire system.
The special decoder can be installed in an electrical panel on a DIN
bar (it occupies six 18 mm DIN modules) or wall-mounted using bolts
(not provided). Terminal boards, configuration dip switches and other
settings must be accessed when the electrical panel is open.
For connecting the remote button (PC terminals) use wires of
minimum cross-section area 0.22mm2with a maximum distance
of 25m.
DESCRIPTION OF TERMINALS
NA Electrical load activation relay normally open contact
NC Electrical load activation relay normally closed contact
C Electrical load activation relay contact common
LINE
}
Non-polarised bus line
LINE
PC
}
Remote button connection terminals
PC
§
SPECIAL DECODING Ref. 1082/80
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
123
Sch.1082/80
NC C
Z
PC
LINE
61 mm
108 mm
(6 DIN modules)
90 mm
The Ref. 1082/80 special decoder is used in 2GO! systems to operate
electrical loads thanks to a relay with 230Vca 5A contact via controls
sent by users through apartment stations or door units in the system.
The main applications are:
Opening garage doors.
Switching staircase lights on.
Switching electrical loads on and off.
SPECIFICATION
The main features are:
Monostable (programmable activation time from 1 second to 10
minutes) or toggle operation.
Possibility of call code activation (from apartment station or
intercom) or alternatively via other system events.
Possibility of connecting a remote activating button (monostable
or toggle).
System programming/failure LED.
Possibility of connecting to system in in/out mode or via Ref.
1082/51 distributor.
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
1
7 6
2 3
5 4
1Configuration dip switch
2Programming button and LED
3Timer adjustment trimmer
4Remote button connection terminals
5Line connection terminals
6Line terminal
7Electrical load activation relay contact terminals
•
•
•
•
•
•
•
•
SPECIAL DECODING Ref. 1082/80
SPECIAL DECODING Ref. 1082/80
SPECIFICATION - TECHNICAL SPECIFICATIONS
DEFAULT CONFIGURATION - INSTALLATION

ACCESSORIES
sec.4c
−−−−
3
2GO! - Technical manual
PROGRAMMING
ON
=
OFF
=
ON
ON
SWITCHING MODE
Firstly, define whether the relay must be controlled in monostable or
toggle mode.
In monostable mode, when an appropriate command is received or
the remote button connected to the PC terminals is pressed, the relay
will be energised for a variable time from 1 second to 10 minutes
according to the setting made using the “timer” trimmer.
In toggle mode, when an appropriate command is received or the
remote button connected to the PC terminals is pressed, the relay will
switch and the trimmer setting will be ignored. The relay will remain
switched until a new command is reached.
ON DIP
4321 5
ON
321
ON
21
ON
21
ON DIP
4321 5
Toggle
Monostable
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
To test the operation time in monostable mode, simply short circuit
the PC terminals provisionally and check the relay energising time.
OPERATING MODE
The special decoder can be configured to be activated by a call (from
a door or intercom unit) by a user code (from 0 to 31) if this is not
already used by apartment stations. Alternatively, it can be activated
by other system events (pressing a door opening button on an
apartment station, pressing the call to switchboard button, pressing
the staircase light button on an apartment station or door unit).
A - OPERATION FOLLOWING A CALL
The position of the PE dip switch is ignored:
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
ON
321
Arrange the COD dip switch in the on position:
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
ON
12
At this point, assign a user code from 0 to 31 to the special decoder.
To do this, set the INF and SUP dip switches to the same value as
the user code chosen using the following table. This code must not
correspond to another user code in the system.
INF/SUP= 6
43215
INF/SUP= 5
43215
INF/SUP= 4
43215
INF/SUP= 7
43215
INF/SUP= 10
43215
INF/SUP= 9
43215
INF/SUP= 8
43215
INF/SUP= 11
43215
INF/SUP= 14
43215
INF/SUP= 13
43215
INF/SUP= 12
43215
INF/SUP= 15
43215
INF/SUP= 18
43215
INF/SUP= 17
43215
INF/SUP= 16
43215
INF/SUP= 19
43215
INF/SUP= 22
43215
INF/SUP= 21
43215
INF/SUP= 20
43215
INF/SUP= 23
43215
INF/SUP= 26
43215
INF/SUP= 25
43215
INF/SUP= 24
43215
INF/SUP= 27
43215
INF/SUP= 2
43215
INF/SUP= 1
43215
INF/SUP= 0
43215
INF/SUP= 3
43215
INF/SUP= 30
43215
INF/SUP= 29
43215
INF/SUP= 28
43215
INF/SUP= 31
43215
At this point, the special decoder is ready to be activated by door
units by means of the programmed call code.
To be activated from an apartment station, the special decoder call
codes must be programmed for all apartment stations which need to
access the service as follows:
1. Go to the apartment station to be programmed.
2. Hold the door opener button pressed and pick up the handset. The
apartment station outputs a tone to indicate that programming is
in progress.
BEE
P
1
2
SPECIAL DECODING Ref. 1082/80
PROGRAMMING
SPECIAL DECODING Ref. 1082/80

ACCESSORIES
4
−−−−
sec.4c 2GO! - Technical manual
3. Press the button to be programmed. The door unit will output a
confirmation tone.
BEEP
3
For buttons meaning, refer to “button function table” in section
1.
On Folio video door phones, the decoder code must be added
to the directory and calls must be made to that code.
4. Go to the special decoder and press the programming button.
The special decoder LED will blink four times and the apartment
station will beep to indicate that programming is over.
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
5. Hook up the handset of apartment station. It will beep to indicate
exit from programming mode.
6. Check programmed function: Pick up the handset, press the
programmed button and then check that the special decoder
service is activated.
7. Hang up.
The auto-on and video switching functions will not be lost if is
programmed for the special decoder call function because these
are available when the handset is off-hook.
B - OPERATION FOLLOWING OTHER EVENTS
Arrange the COD dip switch in the off position:
ON DIP
4321 5
ON
321
ON
21 ON
12
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
In this way, the special decoder can be activated alternatively by one
of the following 3 events:
1. Pressure of the door opening button on an apartment station.
2. Pressure of the switchboard calling button on an apartment
station.
3. Pressure of the staircase light button on an apartment station
and/or door unit.
§
§
1. Operation following pressure of the door opening button on
an apartment station
This service can be activated by pressing on an apartment station
the door opener button in any instant, also not following reception
of a call.
The PE dip switches may be arranged in any position but the COD
switch must be OFF:
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
ON
321
At this point, the group of users which must activate the special
decoder by pressing the door opener button must be defined.
This group must coincide with the users comprised when the
code set in INF and that set in SUP.
1234
LINE4 LINE3 LINE2 LINE1 LINE0
9
8
0
INF= 0
SUP= 8
Ref. 1082/80
TC
In the configuration example shown, the users with code from 0
to 8 can switch the special decoder relay while this function is not
allowed to users with code 9.
The last operation is self-learning of the “door opener button
pressure” event. Press the special decoder programming button.
The LED will start blinking.
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
SPECIAL DECODING Ref. 1082/80
SPECIAL DECODING Ref. 1082/80
PROGRAMMING

ACCESSORIES
sec.4c
−−−−
5
2GO! - Technical manual
Go to any user and press the door opener button. The LED will go
out to indicate that programming is over.
2. Operation following pressure of the switchboard calling
button on an apartment station
The service can be activated by pressing the switchboard call
button on apartment stations with handset off-hook.
The apartment station switchboard call button / /on the
video door phone or 2 on the door phone can be used for this
function only when the handset is off-hook and not following a call
providing if was not programmed for the intercom call function.
If this button was programmed for intercom call functions, the
switchboard call function is lost. In this case, restore the bracket
default settings, program the intercom function on another button;
alternatively, activate the special decoder by means of another
event.
The PE dip switches may be arranged in any position but the COD
switch must be OFF:
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
ON
321
At this point, the group of users which must activate the special
decoder by pressing the switchboard call button must be defined.
This group must coincide with the users comprised when the
code set in INF and that set in SUP.
1234
LINE4 LINE3 LINE2 LINE1 LINE0
9
8
0
INF= 0
SUP= 8
Ref. 1082/80
TC
In the configuration example shown, the users with code from 0
to 8 can switch the special decoder relay while this function is not
allowed to users with code 9.
The last operation is self-learning of the “switchboard call button
pressure” event. Press the special decoder programming button.
The LED will start blinking.
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
Go to any user, pick up the hanset and press the switchboard call
button. The LED will go out to indicate that programming is over.
3. Operation following pressure of the staircase light button on
an apartment station and/or door unit
This service can be activated by pressing the staircase light
function button after receiving a call or during a conversation on
an apartment station.
The apartment station staircase light button is the / /
on the video door phone or 3 on the door phone. It assumes
this function only after receiving a call, in auto-on mode or in
audio mode. The service can also be activated by pressing the
programmed “staircase light” function button (see below) on
apartment stations.
The position of the PE dip switch is not relevant for operation
using an apartment station button but the COD switch must be
OFF:
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
ON
321
At this point, the group of users which must activate the special
decoder by pressing the staircase light button must be defined.
This group must coincide with the users comprised when the
code set in INF and that set in SUP.
SPECIAL DECODING Ref. 1082/80
PROGRAMMING
SPECIAL DECODING Ref. 1082/80

ACCESSORIES
6
−−−−
sec.4c 2GO! - Technical manual
1234
LINE4 LINE3 LINE2 LINE1 LINE0
9
8
0
INF= 0
SUP= 8
Ref. 1082/80
TC
The last operation is self-learning of the “staircase light button
pressure” event. Press the special decoder programming button.
The LED will go on.
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
Go to any user, request door unit auto power-on and press the
staircase light button.
The led will go out to indicate that programming is over.
The special decoder can be activated also by pressing the
apartment station staircase lights. Position the PE dip switches
corresponding to the codes of the apartment station that must
activate it to the ON position:
1234
LINE4 LINE3 LINE2 LINE1 LINE0
Ref. 1082/80
ID= 2ID= 1 ID= 3
ON
32
PE
1
TC TC TC
In the configuration example shown, the special decoder can be
activated by pressing the staircase light button of door units with
ID 1 and 3; it cannot be activated from door unit with ID = 2.
At this point, program a staircase light function for each door unit
which must activate the special decoder.
1. Set the dip switch ID to 0 to start programming the door unit. The
door unit will beep every five seconds to indicate that programming
is in progress and the yellow LED will be on.
ID
12
ON
2. Hold the button to be assigned to the staircase light function
pressed. The door unit will beep when the button is pressed and
beep again after three seconds. Release the button immediately.
STAIRCASE LIGHTS
BEEP _ _ _ 3s _ _ _ BEE
P
3. Reposition the ID dip switches of the door unit in the correct
setting. The yellow LED of the door unit will go out.
4. At this point, run “staircase light button pressure” self-learning
unless this procedure has already been run on apartment
stations.
Press the special decoder programming button. The LED will go
on.
ON DIP
4321 5
ON
321
ON
21
ON DIP
4321 5
ON
PE
NA
INF SUP COD M/T PROG TIMER
OFF=M
ON=T
ON
ON
Sch.1082/80
NC C
Z
PCLINE
SPECIAL DECODING Ref. 1082/80
SPECIAL DECODING Ref. 1082/80
PROGRAMMING

ACCESSORIES
sec.4c
−−−−
7
2GO! - Technical manual
Go to the door unit and press the staircase light button. The
special decoder LED will go out to indicate that programming is
over.
If during programming, the button is held pressed for longer than
five seconds, all optional programming of the apartment station
will be returned to default settings (last user code in column =
31; surveillance cameras = not present; staircase lights button =
not present). Programming will need to be repeated.
§
CONFIGURATION AND OPERATION SUMMARY TABLE
Configurations PE
2
Any
Any
Any
Any Any
Switch the
buttons
corresponding
to the apartment
stations which
must activate the
special decoder to
the on position
13
Program
a value from
1” to 10’ of
M/T= OFF
Program
a value from
1” to 10’ of
M/T= OFF
Program
a value from
1” to 10’ of
M/T= OFF
Program
a value from
1” to 10’ of
M/T= OFF
Program
a value from
1” to 10’ of
M/T= OFF
Any
Program UT
user code
from 0 to 31
(must be INF= SUP
and not be the same
as any other user
code
in the system)
Program
the user group
for activating
the special decoder
(must be
INF<= SUP)
Program
the user group
for activating
the special decoder
(must be
INF<= SUP)
Program
the user group
for activating
the special decoder
(must be
INF<= SUP)
1 2 3 4 5
INF
1 2 3 4 5
SUP
1
ON
OFF
OFF
OFF
COD
OFF
ON
2
OFF
ON
OFF
ON
OFF
ON
OFF
ON
M/T TIMER Other programming
Program the intercom code
on an apartment station button
for activating
the special decoder.
The apartment stations are
all enabled
to activate the specialdecoder
by pressing the user code
call button.
Run “door opener
button pressure”
self-learning procedure
on special decoder
Run “switchboard
call button pressure”
self-learning procedure
on special decoder
Run “staircase
lights button pressure”
self-learning procedure
on special decoder.
Program the staircase
light button
on apartment stations
which must activate
the special decoder
Call from user
to door unit
or intercom call
Pressure of the door
opening button
on an
apartment station
Pressure of the
switchboard
calling button
on an
apartment station
Pressure of the
staircase light
button on an
apartment station
and/or door unit
Pressure of the
special decoder
remote button
(PC terminals)
Activation
following:
SPECIAL DECODING Ref. 1082/80
CONFIGURATION AND OPERATION SUMMARY TABLE
SPECIAL DECODING Ref. 1082/80

ACCESSORIES
8
−−−−
sec.4c 2GO! - Technical manual
WIRELESS CALL REPEATER Ref. 4311/13
The Ref. 4311/13 can be used to radio transmit the call signal from a
door phone system or video door phone system to a Mistral receiver.
The call repeater can be used in combination with the following
ringers:
Ringer with a range of up to 200m,
flash and powering by batteries or power supply unit Ref. 4311/2
Ringer with a range of up to 150m,
flash and 230Vac powering from the electricity mains Ref. 4311/3
Refer to the “Product Technical Manual - Door Phone and Video Door
Phone systems” for ringers, features and installation procedures.
The device is ready to be powered by a 9V battery (not included)
which ensures system operation also in unfavorable conditions. The
battery must be replaced approximately every two years or when the
device performance degrades.
TECHNICAL SPECIFICATIONS
Power: alkaline 6LR61 9V battery
Transmission frequency: 868,35MHz
Dimensions (L x H x P: 85 x 85 x 30mm
Working temperature range: +5 ÷ 40°C
INSTALLATION
Install the device away from sources of heat and in a place protected
from humidity and water sprays.
Be very careful when handling printed circuit components and
particularly the metallic antenna during installation and programming.
The metallic antenna must not be moved from its original position.
Before final installation of the device, make a test call to check that the
radio signal is correctly picked up by the receiver.
Open the product using a screwdriver as a lever in the points shown
(A).
A
•
•
•
Using the bolts and holes provided (B), fasten when screws the
product near the door phone or in a position where the connection
wires of the device it can be intercepted
B
B
D C
Connect to the terminal board as shown in the system diagram
below. Do not disconnect the 2-way battery cable from the terminal
board.
Connect the battery (D).
The signal can be sent to the receiver during programming by
pressing the button (C) on the printed circuit. The indicator LED will
start blinking.
For programming the receiver, refer to the wireless ringer instruction
paragraph.
WIRING DIAGRAM
Ref.4311/13
Cm
C+
C-
S+
S-
S+
LINE
LINE
FROM RISER COLUMN
•
•
•
•
•
WIRELESS CALL REPEATER Ref. 4311/13
WIRELESS CALL REPEATER REF. 4311/13
TECHNICAL SPECIFICATIONS
INSTALLATION

ACCESSORIES
sec.4c
−−−−
9
2GO! - Technical manual
VIDEO MEMORY MODULE Ref. 1082/88
SEGRETERIA
VIDEOCITOFONICA
Sch./Ref.
1082/88
180 mm
(10 DIN modules)
90 mm
55 mm
The Ref. 1082/88 video door phone answering machine (SVC for
short) is designed for 2GO! systems for storing films of unanswered
calls recorded by a video door phone station.
In brief, the functions of the SVC include:
Centralised function: up to eight 7-second films can be stored for
each user (up to 32) in the system.
Users can play and delete the films by pressing the rhomboid
button on the video door phone.
Films can be sent as MMS messages by a Ref. 1082/52 GPRS
modem. This function is available for the one-family 2GO! kits only
and can be activated and deactivated by appropriately connecting
two dedicated terminals.
Date, time, and other diagnostic messages appear on a four-digit
display.
Three buttons for adjusting date and time and using other test
functions.
SEGRETERIA
VIDEOCITOFONICA
Sch./Ref.
1082/88

Display
Function
buttons
Transformer
(provided)
Serial
modem port
Line terminal
Led
3214
7658
TECHNICAL SPECIFICATIONS
Terminal power (0~, 12~): 13Vac ÷ 21Vac
15Vdc ÷ 28Vdc
Maximum terminal draw (0~, 12~): 350mAdc
Temperature: -5°C / +45°C
Memory capacity: 8 films per user
7 seconds per film
user manager
This is a class A device. The device can cause radio interference
in residential environments. The installer may need to take
appropriate measures in such a case.
•
•
•
•
•
§
INSTALLATION
For the installation are valid the generic rules of the 2GO! system.
Observe the following rules:
1. Maximum number of devices: Only one SVC can be installed
in a 2GO! system. This device is included in the TOTAL count of
2GO! devices. Possible system configurations:
3 door units, 1 SVC, 31 apartment stations, 31 distributors.
2 door units, 1 SVC, 32 apartment stations, 31 distributors.
2. Type of usable wires. The same distances for Atlantico video
door phone apartment stations using the same types of wire apply
for connecting the SVC to the system (LINE terminals). Refer to
the section 2.
3. Wiring and line terminals. The SVC can be connected in in-
out mode (Z terminal = OFF), via distributor (Z terminal = ON) or
directly to a power line (Z terminal = ON).
1234
LINE4 LINE3 LINE2 LINE1 LINE0
Terminal
ON
Terminal
ON
Terminal
ON
3
2
14
7
6
58
TC
Terminal
OFF
Terminal
ON
1234
LINE4 LINE3 LINE2 LINE1 LINE0
Terminal
ON
3
2
14
7
6
58
TC
1234
LINE4 LINE3 LINE2 LINE1 LINE0
(IN/OUT)
LINE
(DER)
LINE
ON
OFF
1082/51 PATENTED
Terminal
ON
Terminal
ON
Terminal
ON
3
2
14
7
6
58
TC
Line terminal
ON
OFF
Z
4. Installation. The SVC can be installed in an electrical panel
on a DIN bar (it occupies ten 18mm DIN modules + two 18mm
DIN modules for the power transformer). Terminal boards and
configuration dip switches are accessible with the electrical panel
open.
•
•
VIDEO MEMORY MODULE REF. 1082/88
TECHNICAL SPECIFICATIONS
INSTALLATION
VIDEO MEMORY MODULE Ref. 1082/88

ACCESSORIES
10
−−−−
sec.4c 2GO! - Technical manual
5. Activation. After installing and testing the rest of the system,
connect and power up the SVC following the normal installation
rules shown in the manual. In particular, if a Ref. 1082/20 power
unit free line is connected to, remember to turn the dip switch on
the line used to the off position on the power unit. Check that the
system is still working normally and that the LED on the SVC is
off.
DESCRIPTION OF TERMINALS
0~
}
Power
12~
LINE 2GO! system connection
MMS MMS messaging activation terminals
If an optional modem is not installed, connect a bridge between
terminals MMS.
OPERATION
RECORDING FILMS
The SVC will start recording a 7 second film a few seconds after a call
from a video door phone calling station is received. The film will be
deleted if the user answers or opens the door. If the user either does
not answer or a call is made to another user, the film will be stored in
the permanent SVC memory. The date and time of the call will also be
stored with the film.
The permanent memory is dimensioned to contain 8 films for each
user in the system. The films started from the first will be deleted
when a new call is received by a user who already has eight previously
stored films.
FILM PLAYBACK
Press the button / /on the video door phone without picking
up the handset to check if films are stored. Three cases can occur:
Case A: The busy tone (series of beeps) will be heard and the video
door phone will not light up. This means that the line is busy because
another conversation is in progress. Try again later.
Case B: The video door phone lights up and the following image
appears:
This means that there are no stored films. The video door phone will
go out after a few seconds.
Case C: If the line is not busy and there are stored films, the video
door phone will light up and the number of stored films will appear:
3
§
The number of films will appear for two seconds and then the first
stored film will be played:
15/05/04 10:27 1/3 7
Recording
date and time
Film number/total number
of stored films
Seconds to the end
of the film
Video n°1
The deletion symbol will appear on a row on the top:
15/05/04 10:27 1/3 5
Instructions
for deleting
the film (blinking)
= X
Video n°1
To delete the film, press the button / to go directly to the next
film. If you do not want to delete the film, wait for it to end. The next
will be played:
15/05/04 11:35 2/3 7
= X
Video n°2
The Urmet Domus logo will appear when all the films have been
deleted and the video door phone will go out after a few seconds.
All playing and deletion functions will be available for 60 seconds after
the button / /is pressed for the first time. After 60 seconds,
the monitor will go out and the line will be freed. Alternatively, the
monitors can be switched off before the timeout by picking up and
hanging up the handset: this will free the line.
The playing cycle will start again from the beginning if all films are
played before the 60 second timeout (less than 8 stored films).
The deletion symbol ( = X) will appear immediately allowing
the immediate deletion of the film.
SV124-0423A
2
3
1
8
5
LINE
MMS
~0
~12
ACTIVATE MMS
TRANSMISSION
2Go! system
Bus line
Ref.1082/88
2GO! VIDEO
MEMORY MODULE
POWER SUPPLY
230Vac/12VCC
OPTIONAL
FOR ONE FAMILY
SYSTEMS
TRANSFORMER
MODEM GPRS
Ref.1082/52
LINE~
§
VIDEO MEMORY MODULE Ref. 1082/88
VIDEO MEMORY MODULE Ref. 1082/88
OPERATION