urmet domus 1058/010 User manual

DS1058-007A LBT8529
STAND ALONE WIRELESS INTERFACE
Ref. 1058/010
INSTALLATION AND USER'S MANUAL
Mod.
1058

2 DS1058-007A
SUMMARY
1GENERAL DESCRIPTION.................................................................................................................... 4
1.1 SYSTEM ARCHITECTURE ......................................................................................................... 4
1.2 SYSTEM MAXIMUM DIMENSIONS ............................................................................................ 4
1.3 SYSTEM COMPONENTS ............................................................................................................ 5
1.3.1 Interface radio module 1058/010 ............................................................................................. 5
1.3.2 Microcontact............................................................................................................................. 5
1.3.3 Indoor IR detector 1058/101 .................................................................................................... 5
1.3.4 Outdoor siren 1058/405 ........................................................................................................... 6
1.3.5 Remote control 1058/035.........................................................................................................6
2USE ....................................................................................................................................................... 7
2.1 ELEMENTS OF RADIO MODULE 1058/010 ............................................................................... 7
2.2 VISUAL AND ACOUSTIC WARNING .......................................................................................... 8
2.2.1 Visual warning.......................................................................................................................... 8
2.2.2 Acoustic warning...................................................................................................................... 8
2.2.3 Details on visual warning ......................................................................................................... 9
2.3 WARNINGS FROM DETECTION DEVICES ............................................................................. 10
2.3.1 Microcontact 1058/201 or 1058/202 ...................................................................................... 10
2.3.2 Detector 1058/101 ................................................................................................................. 10
2.4 WARNINGS FROM ACTUATION DEVICES (SIRENS)............................................................. 11
2.4.1 Siren 1058/405....................................................................................................................... 11
2.5 CONTROL DEVICE WARNINGS............................................................................................... 11
2.6 ARM AND DISARM MODULE 1058/010 ................................................................................... 11
2.6.1 From remote control............................................................................................................... 11
2.6.2 From external control ............................................................................................................. 11
3SYSTEM DESIGN ............................................................................................................................... 12
3.1 WARNINGS FOR CORRECT INSTALLATION.......................................................................... 12
3.2 OPERATING MODES ................................................................................................................ 13
3.2.1 Detection devices alarm status .............................................................................................. 13
3.2.2 Physical sabotage.................................................................................................................. 13
3.2.3 Radio sabotage or radio communications jammed................................................................ 13
3.2.4 Battery low condition.............................................................................................................. 13
4INSTALLATION ................................................................................................................................... 14
4.1 RADIO MODULE 1058/010........................................................................................................ 14
4.1.1 Fastening ............................................................................................................................... 14
4.1.2 Connection to power supply................................................................................................... 16
4.1.3 Connections to wired alarm control panel.............................................................................. 17
4.1.4 Configuration of radio module 1058/010................................................................................ 22
4.1.5 Supervision function............................................................................................................... 23
4.2 MICRO CONTACT 1058/201 OR 1058/202............................................................................... 23
4.2.1 Power supply ......................................................................................................................... 23
4.2.2 Acquiring detection devices ................................................................................................... 24
4.2.3 Fastening ............................................................................................................................... 24
4.2.4 Connection to external detectors ........................................................................................... 25
4.2.5 Configuration.......................................................................................................................... 25
4.3 IR INDOOR DETECTOR 1058/101............................................................................................ 26
4.3.1 Power supply ......................................................................................................................... 26
4.3.2 Acquisition.............................................................................................................................. 26
4.3.3 Fastening ............................................................................................................................... 26

DS1058-007A 3
4.3.4 Configuration.......................................................................................................................... 27
4.4 OUTDOOR SIREN 1058/405 ..................................................................................................... 27
4.4.1 Power supply ......................................................................................................................... 27
4.4.2 Acquisition.............................................................................................................................. 27
4.4.3 Fastening ............................................................................................................................... 28
4.4.4 Configuration.......................................................................................................................... 28
4.5 REMOTE CONTROL 1058/035 ................................................................................................. 29
4.5.1 Power supply ......................................................................................................................... 29
4.5.2 Acquiring control device......................................................................................................... 29
5TEST ................................................................................................................................................... 30
5.1 TEST DETECTION DEVICES.................................................................................................... 30
5.2 TEST ACTUATION DEVICES.................................................................................................... 31
5.3 TEST REMOTE CONTROL ....................................................................................................... 31
5.4 USER TRAINING ....................................................................................................................... 31
6MAINTENANCE .................................................................................................................................. 32
6.1 DEVICES.................................................................................................................................... 32
6.1.1 Adding a device ..................................................................................................................... 32
6.1.2 Removing a device ................................................................................................................ 32
6.1.3 Replacing a device................................................................................................................. 33
6.2 REPLACING BATTERIES.......................................................................................................... 33
6.2.1 Opening micro contact 1058/201 or 1058/202....................................................................... 34
6.2.2 Opening IR detector 1058/101............................................................................................... 34
6.2.3 Opening the battery compartment of 1058/405 siren............................................................. 35
6.3 RESET........................................................................................................................................ 35
6.3.1 Reset radio module 1058/010................................................................................................ 35
6.3.2 Reset sirens ........................................................................................................................... 35
7TECHNICAL CHARACTERISTICS ..................................................................................................... 36
7.1 INTERFACE RADIO MODULE 1058/010 .................................................................................. 36
7.2 MICROCONTACT 1058/201 OR 1058/202................................................................................ 37
7.3 INDOOR IR DETECTOR 1058/101............................................................................................ 37
7.4 OUTDOOR SIREN 1058/405 ..................................................................................................... 38
7.5 REMOTE CONTROL 1058/035 ................................................................................................. 38
8DEFAULT SETTINGS ......................................................................................................................... 39

4 DS1058-007A
1 GENERAL DESCRIPTION
1.1 SYSTEM ARCHITECTURE
1058/010 system allows to add wireless devices to an anti-intrusion system, although not prearranged to
manage radio devices.
The system includes a bidirectional radio module interfacing to the inputs and outputs of any wired control
panel, and a range of detectors and wireless devices by which existing anti-intrusion system can be
extended.
Wireless communication is bidirectional and the system is provided with protection means against physical
sabotage and radio sabotage (jamming).
The constancy of radio communications between devices and radio module 1058/010 is controlled by
supervision function.
The system can be programmed and personalised according to individual needs.
The status of system and single detectors is displayed via LEDs.
Radio module 1058/010 takes power supply out of wired control panel it is connected to, while wireless
devices are supplied via lithium batteries.
1.2 SYSTEM MAXIMUM DIMENSIONS
Bidirectional radio module 1058/010 can manage up to:
•16 radio input devices (micro contacts 1058/201 or 1058/202 and volumetric detectors 1058/101) on
choice.
•2 outdoor sirens 1058/405.
•8 remote controls 1058/035.
•8 output connections to wired alarm control panel for detectors warnings.
•4 alarm connections to wired alarm control panel.
•2 output connections per command and status repetition to wired alarm control panel.
•2 input connections from wired alarm control panel.

DS1058-007A 5
1.3 SYSTEM COMPONENTS
1.3.1 Interface radio module 1058/010
Outdoor bidirectional radio module controls the whole wireless system and
processes information from peripheral units; it makes up the interface between
wired alarm control panel and wireless devices.
The module includes:
•8 outputs with solid state relays for warnings from wireless detectors;
•1 output with solid state relays for physical sabotage alarm warning;
•1 output with solid state relays for radio sabotage alarm warning;
•1 output with solid state relays for battery low warning;
•1 output with solid state relays for arming/disarming command via remote
control;
•1 output with solid state relays for radio module (arm/disarm) status
repetition;
•1 input for radio module tamper;
•1 input S to detect wired alarm control panel status;
•1 input BL to arm wireless sirens from wired alarm control panel.
The module takes power supply out of wired alarm control panel it is connected to.
Other radio module characteristics are:
•protection against opening and removal;
•relays which can be biased by jumpers;
•status and warning LEDs.
1.3.2 Microcontact
Magnetic detector to detect opening or closing status in door or window it is
mounted on. It is supplied by a lithium battery and communicates via radio with
radio module 1058/010 in bidirectional mode.
The Microcontact has a programmable auxiliary input, to which there can be
connected either other NC (normally closed) detectors (e.g. magnetic detectors)
or a shutter detector; microcontact has also LEDs to warn about radio
communication. Programming is by jumpers. A tamper assures protection against
opening and removal.
The device has test, supervision and battery low warning functions.
The microcontact is available in two versions:
•White colour 1058/201
•Brown colour 1058/202
1.3.3 Indoor IR detector 1058/101
Detector with passive infrared rays to detect movements in area supervised by it.
It is supplied by a lithium battery and communicates via radio with radio module
1058/010 in bidirectional mode.
Detector 1058/101 has LEDs to warn about radio communication.
A tamper assures protection against opening and removal.
The detector can be mounted in angular position by provided support.
The device has test, supervision and battery low warning functions.

6 DS1058-007A
1.3.4 Outdoor siren 1058/405
Siren suitable to outdoor installation acoustically and optically warning, by strobe,
about an alarm condition when receiving alarm condition signal from radio module
1058/010.
The siren is supplied by alkaline batteries and communicates via radio with radio
module 1058/010 in bidirectional mode.
Siren programming and ringing times are by DIP switch. A tamper assures
protection against opening and removal.
The device has test, supervision and battery low warning functions.
1.3.5 Remote control 1058/035
Remote control allowing to arm and disarm module 1058/010.
The remote control is supplied by a lithium battery and communicates via radio
with radio module 1058/010 in bidirectional mode.
The device has both two-colour LEDs for command sent and battery low
warnings and a buzzer for warning about command received from radio module.

DS1058-007A 7
2 USE
2.1 ELEMENTS OF RADIO MODULE 1058/010
1. LED for alarm warning
2. LED for identification of device typology
3. Status LED of corresponding input 1÷16
4. Control key
5. LED for (armed/disarmed) status warning

8 DS1058-007A
2.2 VISUAL AND ACOUSTIC WARNING
2.2.1 Visual warning
Radio module 1058/010 front side is provided with LEDs displaying the status of system and its radio
devices.
LED Colour Meaning On Off
1 ÷ 16 Red Status of corresponding
radio detector
Input open or
movement detected
Input closed or no
movement
Red Physical sabotage Tampers of one or more
devices stressed
(device open).
LED blinking until user
examines alarm details
No sabotage to
devices
Red Radio sabotage •One or more
devices did not
reply to supervision
•A radio
transmission tries to
black out
communications
LED blinks until user
examines alarm details
No sabotage to
devices
Yellow Battery status One or more devices
are in battery low
condition
Battery charger
suitable
Green Device type identification Indicating that the
device is a detector
(microcontact or IR
detector)
Green Device type identification Indicating that involved
device is a siren
Green Device type identification Indicating that involved
device is remote control
Green Status 1058/010 On steady: armed
Blinking: disarmed
Lack of power supply
2.2.2 Acoustic warning
If enabled by programming, radio module 1058/010 buzzer sends out acoustic warnings in following cases:
•arm: 1 long beep;
•disarm: 3 long beeps;
•test on inputs: one beep whenever a detector (micro contact or IR detector) is stressed.

DS1058-007A 9
2.2.3 Details on visual warning
Detection device open/closed status is immediately identified by its LED (there is one LED per input).
Physical sabotage warning ( )
1. Press once control pushbutton at the front side on radio module 1058/010: 3 beeps are sent out
and LED stops blinking and is lit steady.
2. Press control pushbutton and keep it pressed for 3 seconds:
•radio module 1058/010 sends out 3 beeps,
•LED goes on steady,
•one or more status LEDs 1÷16 go on to show which detection devices (microcontacts and IR
detectors) have had tamper open
3. Press control pushbutton:
•radio module 1058/010 sends out 1 beep,
•LED goes off and LED goes on steady,
•one or more status LEDs 1÷2 go on to show which actuation devices (sirens) have had
tamper open.
4. Press control pushbutton and keep it pressed for 3 seconds:
•radio module 1058/010 sends out 3 beeps,
•if the tampers of all wireless devices are closed, LED goes off and alarm memory is
erased; otherwise, the LED resumes blinking.
5. Radio module 1058/010 returns to normal operation.
Warning: physical sabotage memory is also erased at every radio module 1058/010, arming operation,
provided that cause generating the alarm is not still present.
Radio sabotage warning ( )
1. Press twice control pushbutton at the front side on radio module 1058/010: 3 beeps are sent out
and LED stops blinking and is lit steady.
2. Press control pushbutton and keep it pressed for 3 seconds:
•radio module 1058/010 sends out 3 beeps,
•LED goes on steady,
•one or more status LEDs 1÷16 go on to show which actuation devices (micro contacts and IR
detectors) have not replied to supervision.
3. Press control pushbutton:
•radio module 1058/010 sends out 3 beeps,
•LED goes off and LED goes on steady,
•one or more status LEDs 1÷2 go on to show which actuation devices (sirens) have not
replied to supervision.
4. Press control pushbutton and keep it pressed for 3 seconds:
•radio module 1058/010 sends out 3 beeps,
•if all wireless devices replied to supervision, LED goes off and alarm memory is erased;
otherwise, the LED resumes blinking.
5. Radio module 1058/010 returns to normal operation.
NOTES:
•if detail LEDs do not go on, radio sabotage is of jamming type;
•if both missing reply to supervision and jamming were enabled and both sabotage types
occurred, radio module 1058/010 will only show details relating to missing supervision.
Warning: radio sabotage memory is also erased at every radio module 1058/010, arming operation,
provided that cause generating the alarm is not still present.

10 DS1058-007A
Battery low warning ( )
1. Press three times control pushbutton at the front side on radio module 1058/010: 3 beeps are
sent out and LED stops blinking and is lit steady.
2. Press control pushbutton and keep it pressed for 3 seconds:
•radio module 1058/010 sends out 3 beeps,
•LED goes on steady,
•one or more status LEDs 1÷16 go on to show which detection devices (microcontacts and IR
detectors) have battery low.
3. Press control pushbutton:
•radio module 1058/010 sends out 3 beeps,
•LED goes off and LED goes on steady,
•one or more status LEDs 1÷2 go on to show which actuation devices (sirens) have battery
low
4. Press control pushbutton and keep it pressed for 3 seconds:
•radio module 1058/010 sends out 3 beeps,
•if the batteries of all wireless devices have a sufficient charge, LED goes off and alarm
memory is erased; otherwise, the LED resumes blinking.
5. Radio module 1058/010 returns to normal operation
Warning: battery low warning goes off as soon as all wireless devices have batteries sufficiently charged,
although alarm details were not controlled.
2.3 WARNINGS FROM DETECTION DEVICES
2.3.1 Microcontact 1058/201 or 1058/202
In normal operation conditions, the microcontact does not warn about transmissions by LED.
Front LED blinks first red (signal sending) then green (reception confirmation from radio module 1058/010)
when:
•Microcontact is in battery low condition.
•The cover was opened or antiremoval (tamper) protection was anyhow armed.
•TEST key was pressed. When in Test mode, the LED will blink whenever the contact is armed.
2.3.2 Detector 1058/101
In normal operation conditions, detector 1058/101 does not warn about transmissions by LED.
Front LED blinks first red (signal sending) then green (reception confirmation from radio module 1058/010)
when:
•The detector is in battery low condition.
•The cover was opened or antiremoval (tamper) protection was anyhow armed.
•TEST key was pressed. When in Test mode, the LED will blink whenever the detector is armed.

DS1058-007A 11
2.4 WARNINGS FROM ACTUATION DEVICES (SIRENS)
2.4.1 Siren 1058/405
In case of alarm command on corresponding 1058/010 input, siren 1058/405 is ringing for programmed
time duration (3, 5 or 10 minutes).
If alarm cause is still present after programmed time has elapsed, the siren does not repeat the alarm.
Siren also provides following indications when 1058/010 module changes its status (armed/disarmed):
Siren Flash lamp
Arm (DIP switch B8 = ON) 1 beep 2 blinking
Disarm (DIP switch B8 = ON) 2 beeps 2 sequential blinking
Disarm (siren battery low condition) 5 beeps 2 sequential blinking
Arm (siren tamper open condition) 5 beeps 2 sequential blinking
Disarm (siren tamper open condition) 5 beeps 4 sequential blinking
2.5 CONTROL DEVICE WARNINGS
Remote control 1058/035 provides following warnings:
LED on The LED is lit:
•In colour red, if a key was pressed, or
•In colour green, if remote control battery charge level is low and the battery has
to be replaced.
Beep Radio module 1058/010 received and acknowledged command sent from remote
control.
Warning: beep sound level is very low and beep sound might be not heard in noisy
environments.
2.6 ARM AND DISARM MODULE 1058/010
2.6.1 From remote control
To arm the system:
1. Press key on remote control: remote control LED will be lit in colour red.
2. Remote control sends out a beep to confirm that radio module 1058/010 If it did not, press key
again to send the command again.
To disarm the system:
1. Press key on remote control: remote control LED will be lit in colour red.
2. Remote control sends out a beep to confirm that radio module 1058/010 received the command.
If it did not, press key again to send the command again.
2.6.2 From external control
Radio module 1058/010 can be armed or disarmed automatically by an external control, e.g. by wired
alarm control panel according to wired alarm control panel status.

12 DS1058-007A
3 SYSTEM DESIGN
3.1 WARNINGS FOR CORRECT INSTALLATION
Maximum distance in the connection between two radio sets is determined by the strength and cleanness
of signal from receiving set. A number of factors may either reduce the strength of received signal or
interfere with signal reception. With proper contrivances, these factors can be removed or minimised.
The strength of radio signal is affected either by the absorption of materials the signal is to run through or
by radio waves reflection phenomena. Below table shows how the different materials affect the power of
transmitted radio signal.
Low absorption Medium absorption High absorption Reflection
Wood (e.g. cabinets,
furniture), plastic,
synthetic materials (e.g.
plexiglas), glass, drilled
bricks (e.g. partition
walls).
Water(e.g. aquariums),
integer bricks, marble.
Concrete, bulletproof
windows, metal
structures (e.g.
household appliances,
piping, railings)
Mirrors, metal
surfaces
In some cases, the signal may practically extinguish, e.g. inside metal cabinets.
On the contrary, radio signal may be jammed by not sufficiently screened electronic equipment, electric
motors or other devices working in radio frequency.
For radio devices correct installation apply following precautions:
•position the devices far from sources of electromagnetic noise, such as electric motors, electric panels,
etc.;
•do not mount the devices on metal surfaces or close to large metal objects, or inside metal structures,
such as metal boxes or cabinets;
•should chosen position not allow suitable radio communication, try to displace the device to another
position to see if radio communication is improving.
Warning: always displace peripheral unit (detector, siren, etc.), not radio module.
To position the various devices, comply with following rules:
•Radio module 1058/010:
omust be mounted close to wired alarm control panel, possibly not on walls made of either
concrete or integer bricks;
oits position must allow to see warning LEDs easily;
oits position must as much as possible be a “middle” position with respect to the various radio
devices.
•Microcontact 1058/201 or 1058/202:
omust be placed inside protected premises;
othe detector must be placed on door or window frame and the magnet must be placed on door or
window frame wing or leaf, as far as possible from pintles or hinges.

DS1058-007A 13
•Indoor IR detector 1058/101
othe detector must not be placed where dust might build up;
othe detector must not be placed near sources of heat or where it may be hit by direct sun light, or
in areas possibly subjected to sudden changes in temperature (e.g. under an air conditioner);
othe detector must be mounted on a rigid surface, free from vibrations, at height ranging between
2 and 2.2 metres;
ofor its positioning, refer to detection diagrams (the detector must be able to cover the area to be
protected);
oavoid that in protected area exist blind zones — because of furniture, shelves, plants etc. —
within which a possible intruder can move;
oproperly aim the detector at the area to be protected, especially if the detector is mounted at
height over 2.2 metres;
oif necessary, more detectors can be mounted in the same environment, without any fear of
interferences.
•Outdoor siren 1058/405
omount the siren in vertical position, on a flat surface;
omount the siren in a position which is clearly visible from the outside and from frequently walked
by places, and cannot be reached without a ladder.
3.2 OPERATING MODES
3.2.1 Detection devices alarm status
Should a micro contact detect door or window opening, or an IR detector identify a movement in controlled
area, then radio module 1058/010 will arm LED corresponding to the input; relating relay output will behave
according to programming performed. When the cause of alarm status dies down, the LED goes off.
For precise operating modes of relay outputs relating to inputs, see paragraph 4.1.4 Configuration of radio
module 1058/010.
3.2.2 Physical sabotage
Should a physical sabotage attempt be detected caused by the opening of the tamper of one or more
devices, then radio module 1058/010 will react as follows:
•LED will blink;
•PHYSICAL SABOTAGE relay output will be armed according to what decided in programming step.
At the closing of all tampers, relay output will be disarmed, while LED will blink until alarm details are
checked.
3.2.3 Radio sabotage or radio communications jammed
Should either a radio sabotage (jamming) attempt be detected or any one of the devices (detectors and
sirens) not reply to supervision message, then radio module 1058/010 will react as follows:
•il LED blink;
•RADIO SABOTAGE relay output will be armed.
At full recovery of radio communications (no jamming and/or supervision working with all devices), relay
output will be disarmed, while LED will blink until alarm details are checked.
3.2.4 Battery low condition
Should one or more devices be in battery low condition, then radio module 1058/010 will react as follows:
•LED blink;
•BATTERY relay output will be armed.
When no device will warn about battery low condition, that is when all low batteries will be replaced, relay
output will be disarmed and LED stop blinking.

14 DS1058-007A
4 INSTALLATION
4.1 RADIO MODULE 1058/010
4.1.1 Fastening
1. Open radio module 1058/010 as illustrated in the following figure:
2. Prearrange passages for cables of connection to wired alarm control panel.
Radio module container base is prearranged with pre-fractured passages: if rear passages and
not side passages are to be used, first remove the electronic board, taking off the four screws that
are placed at the corners.

DS1058-007A 15
3. Secure radio module to a flat wall, using fixing plugs supplied.
The following figure shows possible alternatives:
•Hanging from slot Aand then blocked by holes Band C. In this case, the electronic board has
not to be taken off.
•Secured to an embedded box with 3 modules, using holes D.
•Secured to an embedded box with 2 modules, using two holes E.
Warning: to assure antiremoval protection to radio module, hole Cmust always be used too.

16 DS1058-007A
4.1.2 Connection to power supply
Radio module 1058/010 takes power supply at 12 V— out of wired alarm control panel it is connected to.
Before making the connection, check for wired control panel to be able to provide current requested by
radio module, that is that overall absorption of control panel, devices, connected to control panel, and radio
module does not exceed the current which control panel power supply unit is able to supply
Power supply cable must be connected at one side to pins + and – of radio module and at the other side to
wired alarm control panel 12 V— output. In connection, observe polarities!
Warning: wired control panel side connection must be downstream of control panel power supply unit and
backup battery to assure radio module 1058/010 power supply also in lack of network power supply (230 V).
NOTE: should control panel not have a current reserve sufficient to supply radio module 1058/010 too,
radio module 1058/010, can also be supplied by an additional power supply unit provided with a backup
battery, such as 1063/091.

DS1058-007A 17
4.1.3 Connections to wired alarm control panel
Relay output connection
Connect radio module relay outputs to wired alarm control panel inputs according to what indicated in the
table. Do not exceed voltages and currents accepted for solid state relays. The status of the relay at rest
(normally open or normally closed) is defined by DIP switches (see paragraph 4.1.4 Configuration of radio
module 1058/010).
Warning: the black dot identifies the pin, which, where the output is polarised to either 12 V or 0 V,
switches over, following the input and its programming. The pin without a black dot has either 12 V or 0 V
fixed potential independently of the status of associated radio device.
Where the radio output is not polarised, the two pins are similar to the ones of a circuit breaker.
Every wired alarm control panel follows specific conventions in naming its inputs and in the type of
connection (normal, balanced or with double balancing) to be made. In the table, for wired control panel
inputs, generic denominations are used. Refer to wired control panel instructions to identify correct inputs
and type of connection to be made.
Warning: where radio module is connected to a wired control panel, you are warned against programming,
on wired control panel, functions (e.g. “Insertion Block”) preventing the system from being armed when
inputs are open.

18 DS1058-007A
Output Jumper Description
OUT1 ÷ OUT8 J1 ÷ J8
Outputs directly associated to detection devices (micro contacts and IR
detectors). Each relay can be associated to two detectors (detectors 1 and 9
at output 1, detectors 2 and 10 at output 2, etc.).
When an input device warns about an alarm, the relay switches over
depending on radio module 1058/010 configuration.
Table Operating modes of output relays OUT1 ÷OUT8 shows possible
output operating modes.
Outputs used are to be connected to wired control panel detector inputs.
SAB J9
If PHYSICAL SABOTAGE function is enabled by programming, the relay
switches over if at least one device warns about physical sabotage
(tamper open). The output can be connected in series to wired alarm
control panel tamper input.
RF SAB J10
If JAMMING DETECTION and/or SUPERVISION ENABLING functions
were enabled by programming, the relay switches over whenever radio
sabotage (jamming and/or missing supervision) is detected. The output
can be connected to wired alarm control panel sabotage input (or in
series to tamper input, where sabotage input is missing).
BATT J11
The relay is armed where one or more devices warn out that battery is
low. The output can be connected to wired alarm control panel faulty
input.
ON/OFF J12
The relay is managed with remote control 1058/035.
When, on remote control, you press radio module 1058/010, arm control,
the relay switches:
•first to OFF and remains OFF for 500 ms and then to ON and remains
ON for 400 ms, if it is configured as NC,
•first to ON and remains ON for 500 ms and then to OFF and remains
OFF for 400 ms, if it is configured as NO.
When, on remote control, you press radio module 1058/010 disarm
control, the relay switches:
•first to OFF and remains OFF for 1000 ms and then to ON and
remains ON for 400 ms, if it is configured as NC,
•first to ON and remains ON for 1000 ms and then to OFF and remains
OFF for 400 ms, if it is configured as NO.
The output can be used to arm and disarm wired alarm control panel,
connecting the output to the “mechanical key” input of wired control panel,
if it is provided with it.
SYS ST J13
Relay output follows radio module 1058/010, armed or disarmed status.
This output can be used to display radio module 1058/010, status, e.g. by
connecting an external LED.
The polarisation of each output can be changed by modifying the position of corresponding jumper.

DS1058-007A 19
DIP switch A5 = OFF
Outputs OUT1÷OUT8 Free from potential Positive polarisation Negative polarisation
at rest Closed contact 12 V 0 V
in alarm condition Open contact - -
DIP switch A5 = ON
Outputs OUT1÷OUT8 Free from potential Positive polarisation Negative polarisation
at rest Open contact - -
in alarm condition Closed contact 12 V 0 V
Operating modes of output relays OUT1 ÷ OUT8
Relay operation mode Subordinated to radio
module status
Operating mode
Enabled
(DIP switch B1 = OFF)
When radio module 1058/010 is armed, the output
follows associated detection device.
Detection device 1 open -> relay 1 armed
Detection device 1 closed -> relay 1 disarmed
Bistable
(DIP switch A4 = OFF)
Disabled
(DIP switch B1 = ON)
The output always follows associated detection
device.
Detection device 1 open -> relay 1 armed
Detection device 1 closed -> relay 1 disarmed
Enabled
(DIP switch B1 = OFF)
When radio module 1058/010 is armed, the output is
armed and remains armed for about 1 second at
every opening operation on associated detection
device.
Monostable
(DIP switch A4 = ON)
Disabled
(DIP switch B1 = ON)
The output is armed and remains armed for about 1
second at every opening operation on associated
detection device.
Tamper 1058/010 connection
Pins TMP are a support to radio module 1058/010 tamper connection and must be taken back to wired
anti-intrusion control panel.

20 DS1058-007A
Connecting inputs
Radio module 1058/010 is provided with inputs through which it can learn wired system status and receive
commands from the system. Input polarity (reference to either positive or negative polarisation) is defined
by DIP switch B6 (see paragraph 4.1.4 Configuration of radio module 1058/010).
Below table shows connections to be made
Input Description
S This input must be connected to an output of wired control panel which follows
control panel status.
The value of voltage depends on input polarity chosen:
•positive polarity (DIP switch B6 = ON): by applying 12 V voltage, the module, if
armed, is disarmed; taking off the voltage, the module, if disarmed, is armed.
•negative polarity (DIP switch B6 = OFF): by applying 0 V voltage, the module, if
armed, is disarmed; taking off the voltage, the module, if disarmed, is armed.
BL This input is used to drive wireless sirens, by acknowledging a voltage at its pin. This
input must be connected to an output of wired control panel which is armed when the
sirens are armed. By applying 12 V voltage to the pin, radio sirens are silenced;
taking off the voltage, the sirens ring.