urmet domus FDi FD-500-481 User manual

Installation guide
HDMI interface / 17’’ screen
Overview
FDI Matelec produces vandal proof digital notice boards and HDMI interfaces for third party screens.
They have been designed to display files set-up on the web software www.ipnoticeboards.com.
The features are the same for both solutions and the HDMI interface can be connected to any tv or
monitor through a HDMI cable.
This install and user guide covers both solutions.
Specifications
17” display
HDMI interface
P U
24VDC 5A
24Vdc
(1A)
or POE
ize
540 x 360 x 50
(H x W x D in mm)
198 x 120 x 40
(H x W x D in mm)
Protection
Tempered glass
(Plastofloat 66) N/A
Max resolution 16/9
1280 x 720 pixels
Max
resolution 4/3
1280 x 1024 pixels
Maxi Size of the media files
(
any extension)
25 Mo
Available formats
JPG, JPEG, PNG, AVI, MPEG, WMV
Memory capacity
2 Go
50-001-815_A

Installation guide
Identification
Wiring diagram
HDMI interface
When the power supply is provided by the POE switch, the cable has to be CAT6 / 90 meters.
If the P U is a 24Vdc/1A, the section of the cable has to be:
1mm² up to 10 meters
1.5mm² up to 20 meters
The HDMI interface has to be plugged to the TV/monitor through a standard HDMI cable.
The “id”number has to be entered in the
ipnoticeboard.com software
IP factory setting
:
DHCP
Notice board Id :
12E . 012 . DE1 . 32E . 0AB . 4C5
D.C : 1726 Fv 3001

Installation guide
17’’ screen
Green led
Brightness
Tamper
24Vcc
button input
Factory use only
button input
Motion sensors input
12Vdc outputs
(motion sensors)

Installation guide
The section of the SU cable has to be:
1mm2 Up to 10 meters
1.5mm2 up to 20 meters
Motion detector and push button wiring
Commissioning
The HDMI interface or the 17” screen needs an internet connection to reach the web software
ipnoticeboard.com
By default, they use DHCP. In case the device needs to use a fix IP address, the FDI Ipsearch tool is
required. The gateway and DN servers need to be entered as the HDMI interface / 17” screen opens
the communication with the ipnoticeboard.com server.
Programming
Open ipnoticeboard.com then create an account if you don’t have one.
Note: a screen or interface ID is required to create your web account.
Create a site
A site is a building or group of buildings where the HDMI interfaces or the 17” screens are installed.
Motion
détector
1
Motion
détector
2
Push
button
24Vdc P U

Installation guide
Click on Add a site
Then fill the information in the empty fields:
Fields with a * are mandatory.

Installation guide
The time zone has to be entered as the system manages time profiles. For example, a scenario can be
displayed on day period but not on time period.
Create a digital notice board (=HDMI Interface or 17” screen)
Click on then enter a name plus the id of the device.
Note: two options are available but the first one “management of the push button” is only possible on
the vandal proof notice board as it has special inputs.
The time profile management gives the availability to display any media on a time range: day time but
not on night time for example.
Click on Validate.
Add a scenario
From the digital notice board setting, choose the “ ictures and video” tab then enter a name.
Add pictures, video, messages or documents to the scenario.
Note : A streaming period can be specified for each media (date and time setting up)
For a picture, it is possible to select the display time (25 secs by default).
For the video, the audio can be ticked or unticked.

Installation guide
Communication status
Both digital notice board or HDMI interface are setup to communicate with the web software.
Therefore, they need to have an internet access.
Every 5 minutes, a connection is triggered from the device to the server to check if any update is
needed.
On the left hand side, the status of the device is displayed with
-The firmware release
-The date and time of the last connection (last time the hdmi interface or notice board opened
a communication with the web server)
-The status of the communication and if the data is fully transferred to the notice board.
A click on the “Full upload” button will force an update of the device.

Installation guide
Information of union harmonisation legislation
FDI MATELEC, as a manufacturer, declares under its sole responsibility that the product IP Notice board
complies with the relevant Union harmonisation legislation:
RED 2014/53/EU – CEM 2014/30/EU – ROH 2011/65/EU
This declaration is fully available on request at [email protected] or on our web site
www.fdimatelec.com under this product part number.
roduct end of life management
Do not throw this product away with household waste. Please use your local recycling collection points
to make sure this product is properly recycled.