Ursalink UG85 User manual

1
UG85 LoRaWAN Gateway
Quick Start Guide
Ursalink Technology Co., Ltd.

www.ursalink.com
1
Welcome
Thank you for choosing Ursalink UG85 LoRaWAN Gateway.
This guide teaches you how to install the UG85 and how to log in the web GUI to configure the device. Once
you complete the installation, refer to the Ursalink UG85 User Guide for instructions on how to perform
configurations on the device.
Related Documents
This Quick Start Guide only explains the installation of Ursalink UG85 LoRaWAN Gateway. For more
functionality and advanced settings, please refer to the relevant documents as below.
Document
Description
Ursalink UG85 Datasheet
Datasheet for the Ursalink UG85 LoRaWAN Gateway.
Ursalink UG85 User Guide
Users can refer to the guide for instruction on how to log in the
web GUI, and how to configure all the settings.
The related documents are available on Ursalink website: http://www.ursalink.com.
Declaration of Conformity
UG85 is in conformity with the essential requirements and other relevant provisions of the CE, FCC, and
RoHS.
For assistance, please contact
Ursalink technical support:
Email: [e-mail]
Tel: [phone]
Fax: [phone]

Ursalink UG85 Quick Start Guide
www.ursalink.com
2
Before you begin to install the UG85 LoRaWAN Gateway, please check the package contents to verify that
you have received the items below.
1.1 Package Contents
1 × UG85
1 × Ethernet Cable
1 × Power Adapter
1 × Stubby LoRa
Antenna
1 × GPS Antenna
(Optional)
1 × Magnetic Cellular
Antenna (Optional)
1 × Stubby Wi-Fi
Antenna (Optional)
1 × Stubby Cellular
Antenna(Optional)
Note: If UG85 support cellular function, magnetic cellular antenna is default choice.
If any of the above items is missing or damaged, please contact your Ursalink sales
representative.
1 × 6-Pin Pluggable
Terminal
1 × DIN Rail Kit
4 × Setscrews
1 × Warranty Card
1. Packing List

Ursalink UG85 Quick Start Guide
www.ursalink.com
3
2.1 Overview
A. Front Panel
UG85 Front Panel
2.2 Dimensions (mm)
2. Hardware Introduction
1WIFI/LTE Antenna
2GPS Antenna
3LoRa Antenna
4LED Indicator Area
POWER: Power Indicator
SYSTEM: Status Indicator
LORA：LoRa Indicator
WIFI: WIFI Indicator
LTE: Cellular Status Indicator
LAN: Ethernet Port Status Indicator
5Serial Port & I/O
6Ethernet WAN/LAN Port
7Console Port
8Power Connector
9SIM and Reset Button Holder

Ursalink UG85 Quick Start Guide
www.ursalink.com
4
2.3 Pinouts
2.4 LED Indicators
LED
Indication
Status
Description
POWER
Power Status
On
The power is switched on
Off
The power is switched off
SYSTEM
System Status
Green Light
Static: Start-up
Blinking slowly: the system is running
properly
Red Light
The system goes wrong
LoRa
LoRa Status
Green Light
Packet Forwarder mode is running well.
Off
Packet Forwarder mode is running off.
WIFI
WIFI Status
Green Light
WIFI is connected
Off
WIFI is disconnected
LTE
Cellular Status
Off
SIM1 or SIM2 is registering or fails to register
(or there are no SIM cards inserted)
Green Light
Blinking slowly: SIM1 or SIM2 has been
registered and is ready for dial-up
Blinking rapidly: SIM1 or SIM2 has been
registered and is dialing up now
Static: SIM1 or SIM2 has been registered and
dialed up successfully
LAN
Ethernet
Port Status
Off
Disconnected
Green Light
Blinking: Transmitting data
Static: Connected
PIN
RS232
DI
DO
Description
1
---
---
OUT
Digital Output
2
---
IN
---
Digital Input
3
GND
---
---
Ground
4
---
COM
COM
Common Ground
5
RXD
---
---
Receive Data
6
TXD
---
---
Transmit Data
PIN
Description
11
Positive
12
Negative

Ursalink UG85 Quick Start Guide
www.ursalink.com
5
2.5 Reset Button
Function
Description
SYSTEM LED
Action
Reboot
Blinking
Press and hold the reset button for about 5-15 seconds.
Static Green
Release the button and wait for system to reboot.
Reset
Blinking
Press and hold the reset button for more than 15 seconds.
Static Green →
Rapidly Blinking
Release the button and wait.
Off → Blinking
The gateway is now reset to factory default.

Ursalink UG85 Quick Start Guide
www.ursalink.com
6
Environmental Requirements
- Power Input: 9-48 VDC
- Power Consumption: Typical 3.3W (Max 6.4 W)
- Operating Temperature: -40°C to 70°C (-40°F -158°F)
- Relative Humidity: 0% to 95% (non-condensing) at 25°C/77°F
3.1 SIM Card Installation
A. Unscrew the cover of the SIM card then B. Put SIM card into the slot and screw it up.
take it off.
3.2 Antenna Installation
Rotate the antenna into the antenna connector accordingly.
The external antenna should be installed vertically always on a site with a good cellular signal.
3. Hardware Installation

Ursalink UG85 Quick Start Guide
www.ursalink.com
7
3.3 Connect the UG85 to a Computer
3.4 Mount the gateway
The gateway can be placed on a desktop or mounted to a wall or a DIN rail.
3.4.1 Wall Mounting (Measured in mm)
Use 4 pcs of M3 × 6 flat head Phillips screws to fix the gateway on the wall.
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.
3.4.2 DIN Rail Mounting (Measured in mm)
Use 2 pieces of M3 × 6 flat head Phillips screws to fix the DIN rail to the gateway, and then hang the DIN rail
on the mounting bracket. It is necessary to choose a standard bracket.
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.

Ursalink UG85 Quick Start Guide
www.ursalink.com
8
3.5 Power Supply Installation
A. Take out the terminal from the gateway and unscrew the bolt on terminal.
B. Screw down the bolt after inserting power cable into the terminal.
Connecting the Power Cable
If you insert wires into the reverse holes, the gateway will not start and you must switch the wires
into the correct holes.
Color
Polarity
Red
+
Yellow
-

Ursalink UG85 Quick Start Guide
www.ursalink.com
9
Getting Started
Please connect PC to GE port of UG85 directly. PC can obtain an IP address, or you can configure a
static IP address manually. The following steps are based on Windows 10 operating system for your
reference.
③Click “Ethernet” (May have different names). ④Click “Properties”.
4. PC Configuration for UG85 Web GUI
①Click “Search Box” to search “Control Panel” on the
Windows 10 taskbar.
②Click “Control Panel” to open it, and then click
“View network status and tasks”.