V-tech Fire Command Rescue Center User manual

© 2014 VTech
Printed in China
91-009683-001 US
User’s Manual
Fire Command Rescue CenterFire Command Rescue CenterT M

2
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®Fire
Command Rescue Center™playset learning toy!
Deploy the two fire trucks to save lives and put out fires! The Go! Go!
Smart Wheels®Fire Command Rescue Center™ features lots of
manipulative features including a launcher, turning fire hydrant, elevator
and much more.
Introduction
7 TRACK
PIECES
FIRE ALARM SMARTPOINT™
FIRE TRUCK
MOVING
ELEVATOR
6 SMARTPOINT™
LOCATIONS
FIRE STATION
CURVED
RAMP
BIG FIRE
TRUCK

3
INCLUDED IN THIS PACKAGE
- One user’s manual
- One Go! Go! Smart Wheels®big fire truck
- One Go! Go! Smart Wheels®SmartPoint™ fire truck
- One fire station building
- One fire station base
- One elevator
- One fire hydrant
- One curved ramp piece
- One straight ramp piece
- One straight track
- One female connector track
- Two 90-degree tracks
- Three male/female connector tracks
Included In This Package

4
WARNING: All packing materials, such as tape, plastic
sheets, packaging locks and tags are not part
of this toy, and should be discarded for your
child’s safety.
ATTENTION: Pour la sécurité de votre enfant, débarrassez-
vous de tous les produits d’emballage tels que
rubans adhésifs, feuilles de plastique, attaches
et étiquettes. Ils ne font pas partie du jouet.
NOTE: Please keep this user’s manual as it contains
important information.
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom
of the SmartPoint™ fire truck. Use
a coin or a screwdriver to loosen the
screw.
3. Install 2 new ‘AAA’ (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new alkaline
batteries is recommended for maximum
performance.)
4. Replace the battery cover and tighten
the screw to secure.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
Getting Started

5
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging
(if removable).
• Rechargeable batteries are only to be charged under adult
supervision.
ASSEMBLY INSTRUCTIONS
With the VTech®Go! Go! Smart Wheels®Fire Command Rescue
Center™, safety comes first. To ensure your child’s safety, adult
assemblyisrequired.
1. Assemble the fire station: Slide the elevator onto the groove on
the side of the fire station building. Then, attach the fire station
building to the station base as shown.
2. Attach the fire hydrant: Attach the fire
hydrant to the fire station base as shown.
You will hear a click sound when it locks into
place.
Assembly Instructions

6
3. Assemble the ramp: Connect the curved and straight ramp pieces
together. Attach the curved ramp piece to the top of the fire station.
After the above steps, connect these pieces to the seven included track
pieces. You can configure them into different shapes.
SMARTPOINT™ FIRE TRUCK FEATURES
1. ON/OFF SWITCH
To turn the unit ON, slide the ON/OFF
SWITCH on the SmartPoint™ fire
truck to the ON ( ) position.To turn the
unit OFF, slide the ON/OFF SWITCH
to the OFF ( ) position.
2. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech®Go! Go! Smart Wheels®
SmartPoint™ fire truck will automatically power-down after
approximately 60 seconds without input. The unit can only be
turned on again by pressing the light-up button or pushing the
smallfiretruckquickly.
NOTE: This product is in a try-me mode in the packaging. After opening
the package, turn the vehicle off and on again to proceed with
normal play.
Product Features

7
NOTE : Ce produit est actuellement en mode démonstration. Une fois
déballé, veuillez éteindre puis remettre en marche ce jouet
pour activer toutes ses fonctionnalités.
SMARTPOINT™ FIRE TRUCK
ACTIVITIES
1. Slide the ON/OFF SWITCH to turn the
unit ON.You will hear fire truck sounds,
a song and a phrase.The light will flash
with the sounds.
2. Press the LIGHT-UP BUTTON to hear
fire truck sounds, songs and phrases.
The light will flash with the sounds.
3. Push the fire truck to hear fun sounds
and melodies. While the melody is
playing, push the fire truck again to add
in fun sounds on top of the melody.The
light will flash with the sounds.
4. For added fun, the SmartPoint™ fire
truck interacts with VTech®Go! Go!
Smart Wheels®playsets. Simply roll
the fire truck over one of the playset’s
SmartPoints™ to see the fire truck’s
light flash and to hear greetings, fun
sounds, short tunes and sing-along
songs (each playset sold separately).
Activities

8
FIRE STATION AND BIG FIRE TRUCK
ACTIVITIES
1. Drive the SmartPoint™ fire truck
over the playset’s six SmartPoints™
to trigger fun sounds, phrases and
sing-along songs.
2. Slide the FIRE ALARM lever to hear a
mechanical alarm sound.
3. Move the ELEVATOR up and down to
lift the SmartPoint™ fire truck to the
top of the station!
4. Launch the SmartPoint™ fire truck
down the CURVED RAMP and pretend
to race to an emergency!
5. Load your SmartPoint™ fire truck
onto the big fire truck to help it get
around. Use the ladder to lift up the
SmartPoint™ fire truck.
Activities

9
Care & Maintenance / Troubleshooting
6. Press the big fire truck’s button to hear
beeping sounds.
7. Move the fire hose and fire extinguisher
on the big fire truck.
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat
source.
3. Remove the batteries when the unit will not be in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
TROUBLESHOOTING
If for some reason the program/activity stops working or malfunctions,
pleasefollowthesesteps:
1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play again.
5. If the product still does not work, replace with a new set of batteries.