V-tech Go! Go! Smart Wheels Press & Race Monster Truck... Assembly Instructions

Parent’s Guide
Monster Truck Rally™
91-003359-007

2
INTRODUCTION
Thank you for purchasing the Go! Go! Smart Wheels®Press & Race™
Monster Truck Rally™by VTech®! Little racers will love watching the
monster truck launch over two jump zones. Place the monster truck on
the Press & Race™ zone to make the flames spin.
Smartpoint®
Press & Race™
Monster Truck
Jump Launcher
2 Smartpoint®
Locations
Stunt
Podium

3
INCLUDED IN THIS PACKAGE
Two ¼ straight
tracks, female
One 90-degree
track, female
One 90-degree
track, male
One ¾ straight track Two cross tracks One long ramp track
One SmartPoint®
launcher
One SmartPoint®
podium platform
SmartPoint®
Press & Race™
monster truck
One short
ramp track
One podium
landing track
Three ¼ straight
tracks

4
JUMP
One podium
jump track
One jump light One podium
board
One ramp sign One ramp gate One label sheet
One small track
support
Two large
podium supports
One ¼ straight
track, male
- One track configuration sheet
- One parent’s guide

5
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy, and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains important
information.
ATTENTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballage tels que rubans adhésifs, feuilles de plastique, attaches,
étiquettes et vis d’emballage. Ils ne font pas partie du jouet.
NOTE : Il est conseillé de conserver ce guide des parents car il
comporte des informations importantes.
Adult assembly required. For your child’s safety, do not let your
child play with the toy until it is fully assembled.
Unlock the packaging lock:
WARNING:
For your child’s safety, do not press and release the vehicle on
clothing, body or hair.
Turn the packaging lock counter-
clockwise several times.
Pull out and discard the packaging lock.

6
GETTING STARTED
BATTERY INSTALLATION
Press & Race™Monster Truck
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the
back of the monster truck. Use a
screwdriver to loosen the screw.
3. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended
for maximum performance.)
4. Replace the battery cover and tighten the screw to secure the
battery cover.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.

7
JUMP
1
2
6
7
8
9
10
3
5a
4a
5b
4b
10
12
7
6
8
5a
5b
4a
4b
9
10
3
LABEL APPLICATION
Please securely adhere the labels to the playset as
indicated below:

8
ASSEMBLY INSTRUCTIONS
Monster Truck Rally™
1. Insert the two Large Podium Supports into the slots underneath
the SmartPoint®Podium Platform.Then, insert the Podium Board
into the SmartPoint®Podium Platform, as shown below.
2. Insert the Small Track Support into the slot underneath the Podium
Jump Track. Then, connect the SmartPoint®Podium Platform to
the Podium Jump Track, as shown below.
3. Attach the Ramp Gate to the Ramp Sign. Then, insert the Ramp
Gate to the Short Ramp Track, as shown below.
With the VTech®Go! Go! Smart Wheels®Press & Race™
Monster Truck Rally™, safety comes first. To ensure your child’s
safety, adult assembly is required.

9
4. Insert the Jump Light to the Podium Landing Track, as shown
below.
5. After the above steps, connect these pieces to the included track
pieces.You can configure them into different arrangements.

10
EXPAND & EXPLORE
Connect to the Go! Go! Smart Wheels
®
3-in-1 Launch
& Play Raceway™ (as shown below) or other Go! Go!
Smart Wheels
®
playsets (each sold separately) to expand
the Press & Race™Monster Truck Rally™ and inspire
creativity.
PRODUCT FEATURES
Press & Race™Monster Truck
1.ON/OFF Switch
To turn the monster truck ON, slide the On/
Off Switch to the ON ( ) position. To turn the
monster truck OFF, slide the On/Off Switch to
the OFF ( ) position.
2.AUTOMATIC SHUT-OFF
To preserve battery life, the included monster
truck will automatically power down after approximately 60 seconds
without input. The unit can be turned on again by pressing the light-
up button, pushing quickly, initiating the press and release feature or
triggering a SmartPoint®location.
Note: If the unit powers down while playing, we suggest changing
the batteries.