V-tech Toot Toot Drivers User manual

Instruction Manual
Fire Station

C
M
Y
CM
MY
CY
CMY
K
Grow with VTech(101x127)bw1P-V2.pdf 1 08/18/2014 9:29:01

2
INTRODUCTION
Thank you for purchasing the VTech®Toot-Toot Drivers®Station.
This busy Fire Engine is coming to the rescue! Little ones will explore
role-play excitement with the Fire Station. Press the bell button to
sound the alarm and launch the Fire Engine into action! Hear phrases,
music and sounds when your vehicle responds to the four SmartPoint™
locations.
SmartPointTM
Fire Engine
4 SmartPointTM
Locations
3 Accessories
( Fire Extinguisher,
Fire Hydrant, Fire)
Lift

3
INCLUDED IN THE PACKAGE
One training tower
with a bell
Ramp track A Ramp track B
Road support A
One fire
extinguisher
Ramp track D
One fireOne SmartPointTM
Fire Engine
Ramp track C
One fire hydrant
One door
One right wall

4
One lift platform One lift track One launcher
piece
One back wall One door top One door floor
One tower One fire flipper
Two door frontsRoad support B Three road
support-middles

5
•Sticker Sheet
•Quick Start Guide
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part
of this toy, and should be discarded for your child’s safety.
NOTE
Please save this manual as it contains important information.
Removing the Packaging Locks:
Pull out the packaging locks and discard.
Turn the packaging locks anticlockwise
several times.
INSTRUCTIONS
Battery Removal And Installation
1. Make sure the unit is turned OFF.
2. Find the battery cover located on
the bottom of the Fire Truck, use a
screwdriver to loosen the screw and
then open the battery cover.
3. Remove old batteries by pulling up on
one end of each battery.
4. Install 2 new AAA (AM-4/LR03)
batteries following the diagram
inside the battery box. (For best
performance, alkaline batteries or fully charged Ni-MH rechargeable
batteries are recommended).
5. Replace the battery cover and tighten the screw to secure.

6
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
MPORTANT: BATTERY INFORMATION
• Insertbatterieswiththecorrectpolarity(+and-).
• Donotmixoldandnewbatteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Onlybatteriesofthesameorequivalenttypeasrecommendedare
to be used.
• Donotshort-circuitthesupplyterminals.
• Removebatteriesduringlongperiodsofnon-use.
• Removeexhaustedbatteriesfromthetoy.
• Disposeofbatteriessafely.Donotdisposeofbatteriesinfire.
RECHARGEABLE BATTERIES
• Removerechargeablebatteries(ifremovable)fromthetoybefore
charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Donotchargenon-rechargeablebatteries.

7
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specified
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in the Batteries and Accumulators Regulation.
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Please dispose of your product and batteries responsibly.
In the UK, give this toy a second life by disposing of it at a small
electricals collection point* so all of its materials can be recycled.
Learn more at:
www.vtech.co.uk/recycle
www.vtech.com.au/sustainability
* Visit www.recyclenow.com to see a list of collection points near you.

8
123
4
6
7
8
9
10
5
LABEL APPLICATION
Please stick the labels to the play set as shown below:
6
1
2
3
7
5
4
8
9
10

9
ASSEMBLY INSTRUCTIONS
1. Assemble the door, door floor and wall components. Following the
steps below:
A. Snap the two door fronts to the door floor. The side with a 1 on
the back should be inserted on the left of the door floor. Insert the
side with a 2 on the back into the right of the door floor, as shown
below. Then Insert the door into the two grooves in the base as
shown.
B. Fix the door top onto the two door fronts, as shown below.
Attach the back wall of the door building using the tabs on the door
floor and door top. You will hear a clicking sound when they are
correctly attached.
With the Toot-Toot Drivers® Fire Station, safety comes first.
To ensure your child’s safety, adult assembly is required.
12