Vacon 10 User manual

INDEX
Document: DPD00717C
Version release date: 20.11.2011
1. Safety 1
1.1 Warnings 1
1.2 Safety instructions 3
1.3 Earthing and earth fault protection 3
1.4 Before running the motor 4
2. Receipt of delivery 5
2.1 Type designation code 5
2.2 Storage 5
2.3 Maintenance 6
2.3.1 Capacitor recharge 6
2.4 Warranty 7
2.5 Manufacturer’s declaration of conformity 8
3. Installation 9
3.1 Mechanical installation 9
3.1.1 Vacon 10 dimensions 10
3.1.2 Cooling 12
3.1.3 Power losses 13
3.1.4 EMC levels 18
3.1.5 Changing the EMC protection class from C2 or C3 to C4 18
3.2 Cabling and connections 20
3.2.1 Power cabling 20
3.2.2 Control cabling 21
3.2.3 Screw of cables 23
3.2.4 Cable and fuse specifications 25
3.2.5 General cabling rules 28
3.2.6 Stripping lengths of motor and mains cables 29
3.2.7 Cable installation and the UL standards 29
3.2.8 Cable and motor insulation checks 29
4. Commissioning 30
4.1 Commissioning steps of Vacon 10 30
5. Fault tracing 32
6. Vacon 10 application Interface 35
6.1 Introduction 35
6.2 Control I/O 37
7. Control panel 38
7.1 General 38
7.2 Display 38
7.3 Keypad 39
7.4 Navigation on the Vacon 10 control panel 41
7.4.1 Main menu 41

8. Standard application parameters 49
8.1 Quick setup par. (Virtual menu, shows when par. 17.2 = 1) 50
8.2 Motor settings (Control panel: Menu PAR -> P1) 52
8.3 Start / stop setup (Control panel: Menu PAR -> P2) 53
8.4 Frequency references (Control panel: Menu PAR -> P3) 54
8.5 Ramps and brakes setup (Control panel: Menu PAR -> P4) 55
8.6 Digital inputs (Control panel: Menu PAR -> P5) 56
8.7 Analogue inputs (Control panel: Menu PAR -> P6) 56
8.8 Digital outputs (Control panel: Menu PAR -> P8) 57
8.9 Analogue outputs (Control panel: Menu PAR -> P9) 57
8.10 Protections (Control panel: Menu PAR -> P13) 58
8.11 Fault autoreset parameters (Control panel: Menu PAR -> P14) 58
8.12 PI control parameters (Control panel: Menu PAR -> P15) 59
8.13 Application Setting (Control panel: Menu PAR -> P17) 59
8.14 System parameters 60
9. Parameter descriptions 62
9.1 Motor settings (Control panel: Menu PAR -> P1) 62
9.2 Start / stop setup (Control panel: Menu PAR -> P2) 67
9.3 Frequency references (Control panel: Menu PAR -> P3) 74
9.4 Ramps & brakes setup (Control panel: Menu PAR -> P4) 75
9.5 Digital inputs (Control panel: Menu PAR -> P5) 79
9.6 Analogue inputs (Control panel: Menu PAR -> P6) 80
9.7 Digital outputs (Control panel: Menu PAR -> P8) 81
9.8 Analogue outputs (Control panel: Menu PAR -> P9) 82
9.9 Protections (Control panel:Menu Par->P13) 83
9.10 Automatic reset (Control panel: Menu PAR -> P14) 87
9.11 PI control parameters (Control panel: Menu PAR -> P15) 88
9.12 Application setting (Control panel: Menu PAR->P17) 89
9.13 Modbus RTU 91
9.13.1 Termination resistor 91
9.13.2 Modbus address area 91
9.13.3 Modbus process data 92
10. Technical data 94
10.1 Vacon 10 technical data 94
10.2 Power ratings 96
10.2.1 Vacon 10 – Mains voltage 208-240 V 96
10.2.2 Vacon 10 – Mains voltage 115 V 97
10.2.3 Vacon 10 – Mains voltage 380-480 V 97
10.2.4 Vacon 10 – Mains voltage 575 V 98
10.3 Brake resistors 98

safety vacon • 1
24-hour support [phone] • Email: [email protected]
1
1. SAFETY
ONLY A COMPETENT ELECTRICIAN IS ALLOWED TO CARRY
OUT THE ELECTRICAL INSTALLATION!
This manual contains clearly marked cautions and warnings which are intended for
your personal safety and to avoid any unintentional damage to the product or con-
nected appliances.
Please read the information included in cautions and warnings carefully:
1.1 Warnings
=Dangerous voltage
Risk of death or severe injury
=General warning
Risk of damage to the product or
connected appliances
The components of the power unit of the frequency converter
are live when Vacon 10 is connected to mains. Coming into
contact with this voltage is extremely dangerous and may
cause death or severe injury. The control unit is isolated from
the mains potential.
The motor terminals U, V, W (T1, T2, T3) and the possible brake
resistor terminals - / + are live when Vacon 10 is connected to
mains, even if the motor is not running.
The control I / O-terminals are isolated from the mains poten-
tial. However, the relay output terminals may have a danger-
ous control voltage present even when Vacon 10 is
disconnected from mains.
The earth leakage current of Vacon 10 frequency converters
exceeds 3.5 mA AC. According to standard EN61800-5-1, a
reinforced protective ground connection must be ensured.
If the frequency converter is used as a part of a machine, the
machine manufacturer is responsible for providing the
machine with a main switch (EN 60204-1).
If Vacon 10 is disconnected from mains while running the
motor, it remains live if the motor is energized by the process.
In this case the motor functions as a generator feeding energy
to the frequency converter.

2• vacon safety
Tel. [phone] • Fax [phone]
1
After disconnecting the frequency converter from the mains,
wait until the fan stops and the indicators on the display go
out. Wait 5 more minutes before doing any work on Vacon 10
connections.
The motor can start automatically after a fault situation, if the
autoreset function has been activated.

safety vacon • 3
24-hour support [phone] • Email: [email protected]
1
1.2 Safety instructions
The Vacon 10 frequency converter has been designed for fixed
installations only.
Do not perform any measurements when the frequency con-
verter is connected to the mains.
Do not perform any voltage withstand tests on any part of
Vacon 10. The product safety is fully tested at factory.
Prior to measurements on the motor or the motor cable, dis-
connect the motor cable from the frequency converter.
Do not open the cover of Vacon 10. Static voltage discharge
from your fingers may damage the components. Opening the
cover may also damage the device. If the cover of Vacon 10 is
opened, warranty becomes void.
1.3 Earthing and earth fault protection
The Vacon 10 frequency converter must always be earthed with an earthing conduc-
tor connected to the earthing terminal. See figure below:
MI1 - MI3
•The earth fault protection inside the frequency converter protects
only the converter itself against earth faults.
•If fault current protective switches are used they must be tested
with the drive with earth fault currents that are possible to arise in
fault situations.

4• vacon safety
Tel. [phone] • Fax [phone]
1
1.4 Before running the motor
Checklist:
Before starting the motor, check that the motor is mounted
properly and ensure that the machine connected to the motor
allows the motor to be started.
Set the maximum motor speed (frequency) according to the
motor and the machine connected to it.
Before reversing the motor shaft rotation direction make sure
that this can be done safely.
Make sure that no power correction capacitors are connected
to the motor cable.

receipt of delivery vacon •5
24-hour support [phone] • Email: [email protected]
2
2. RECEIPT OF DELIVERY
After unpacking the product, check that no signs of transport damages are to be
found on the product and that the delivery is complete (compare the type designation
of the product to the code below).
Should the drive have been damaged during the shipping, please contact primarily
the cargo insurance company or the carrier.
If the delivery does not correspond to your order, contact the supplier immediately.
2.1 Type designation code
Figure 2.1: Vacon 10 type designation code
2.2 Storage
If the frequency converter is to be kept in store before use make sure that the ambi-
ent conditions are acceptable:
Storing temperature -40…+70°C
Relative humidity < 95%, no condensation
VACON0010- 1L- 0001- 1 +OPTIONS
Vacon 10
1L = Single phase
3L = Three phases
1 =115V
2 = 208 - 230V
4 = 380 - 480V
7 = 575V
Output Current
Input Voltage
+Options
EMC2
QPES
+DLNL = Dutch
+DLNO = Norwegian
+DLPT = Portuguese
+DLRU = Russian
+DLSE = Swedish
+DLTR = Turkish
+DLUS = US English
empty = English
Language of the documentation
+DLCN = Chinese
+DLCZ = Czech
+DLDE = German
+DLDK = Danish
+DLES = Spanish
+DLFI = Finnish
+DLFR = French
+DLIT = Italian
Input phase

6•vacon receipt of delivery
Tel. [phone] • Fax [phone]
2
2.3 Maintenance
In normal operating conditions, Vacon 10 frequency converters are maintenance-
free. However, regular maintenance is recommended to ensure a trouble-free oper-
ating and a long lifetime of the drive. We recommended to follow the table below for
maintenance intervals.
2.3.1 Capacitor recharge
After a longer storage time the capacitors need to be recharge in order to avoid ca-
pacitor damage. Possible high leakage current through the capacitors must be lim-
ited. The best way to achieve this is to use a DC-power supply with adjustable current
limit.
1) Set the current limit to 300…800 mA according to the size of the drive.
2) Then connect the DC-power supply to the input phase L1 and L2.
3) Then set the DC-voltage to the nominal DC-voltage level of the (1.35*Un AC) and
supply the converter for at least 1 h.
If DC-voltage is not available and the unit has been stored much longer than 12
months deenergized, consult the factory before connecting power.
Maintenance interval Maintenance action
Whenever necessary • Clean headsink
Regular • Check tightening torques of terminals
12 months (If stored)
• Check input and output terminals and con-
trol I / O terminals.
• Clean cooling tunnel.
• Check operation of cooling fan, check for
corrosion on terminals, busbars and other
surfaces.
6 - 24 months (depending on environment)
• Chang cooling fans:
• Main fan
• Interminal fan
5 - 7 years • The motor cables should cross other cables
at an angle of 90 degrees.

receipt of delivery vacon •7
24-hour support [phone] • Email: [email protected]
2
2.4 Warranty
Only manufacturing defects are covered by the warranty. The manufacturer as-
sumes no responsibility for damages caused during or resulting from transport, re-
ceipt of the delivery, installation, commissioning or use.
The manufacturer shall in no event and under no circumstances be held responsible
for damages and failures resulting from misuse, wrong installation, unacceptable
ambient temperature, dust, corrosive substances or operation outside the rated
specifications. Neither can the manufacturer be held responsible for consequential
damages.
The Manufacturer's time of warranty is 18 months from the delivery or 12 months
from the commissioning whichever expires first (Vacon Warranty Terms).
The local distributor may grant a warranty time different from the above. This war-
ranty time shall be specified in the distributor's sales and warranty terms. Vacon as-
sumes no responsibility for any other warranties than that granted by Vacon itself.
In all matters concerning the warranty, please contact first your distributor.

8•vacon receipt of delivery
Tel. [phone] • Fax [phone]
2
2.5 Manufacturer’s declaration of conformity
EU DECLARATION OF CONFORMITY
We
Manufacturer's name: Vacon Oyj
Manufacturer's address: P.O.Box 25
Runsorintie 7
FIN-65381 Vaasa
Finland
hereby declare that the product
Product name: Vacon 10 Frequency Converter
Model designation: Vacon101L00012…to 00092
Vacon103L00012…to 00112
Vacon103L00014…to 00124
has been designed and manufactured in accordance with the following
standards:
Safety: EN 60204 -1 (2009) (as relevant) ,
EN 61800-5-1 (2007)
EMC: EN 61800-3 (2004)
and conforms to the relevant safety provisions of the Low Voltage Directive
2006/95/EC and EMC Directive 2004/108/EC.
It is ensured through internal measures and quality control that the product
conforms at all times to the requirements of the current Directive and the
relevant standards.
In Vaasa, 30th of July, 2010
Vesa Laisi
President
The year the CE marking was affixed: 2011

installation vacon • 9
24-hour support (0)201 212 575 • Email: [email protected]
3
3 INSTALLATION
3.1 Mechanical installation
There are two possible ways to mount Vacon 10 in the wall. For MI1-MI3, either screw
or DIN-rail mounting. The mounting dimensions are given on the back of the drive
and on the following page.
Figure 3.1: Screw mounting, MI1 - MI3
Figure 3.2: DIN-rail mounting, MI1 - MI3
= M5
MI3
MI1
=M4
MI2
=M5
LOC
REM
BACK
RESET
OK
LOC
REM
BACK
RESET
OK
LOC
REM
BACK
RESET
OK
12

10 • vacon installation
Tel. [phone] • Fax [phone]
3
3.1.1 Vacon 10 dimensions
Figure 3.3: Vacon 10 dimensions, MI1 - MI3
Type H1 H2 H3 W1 W2 W3 D1 D2
MI1 160.1 147 137.3 65.5 37.8 4.5 98.5 7
MI2 195 183 170 90 62.5 5.5 101.5 7
MI3 254.3 244 229.3 100 75 5.5 108.5 7
Table 1: Vacon 10 dimensions in millimetres
Frame Dimensions(mm) Weight*
W H D (kg.)
MI1 66 157 98 0.5
MI2 90 195 102 0.7
MI3 100 262 109 1
*without shipping package
Table 2: Vacon 10 frame dimensions (mm) and weights (kg)
W1 D1
H3
D2
H1
W2
W3
H2
LOC
REM
BACK
RESET
OK

installation vacon • 11
24-hour support (0)201 212 575 • Email: [email protected]
3
Frame Dimensions(Inches) Weight*
W H D (Ibs.)
MI1 2.6 6.2 3.9 1.2
MI2 3.5 9.9 4 1.5
MI3 3.9 10.3 4.3 2.2
*without shipping package
Table 3: Vacon 10 frame dimensions (Inch) and weights (Ibs)

12 • vacon installation
Tel. [phone] • Fax [phone]
3
3.1.2 Cooling
Enough free space shall be left above and below the frequency converter to ensure
sufficient air circulation and cooling. You will find the required dimensions for free
space in the table below.
If several units are mounted above each other the required free space equals C + D
(see Installation space). Moreover, the outlet air used for cooling by the lower unit
must be directed away from the air intake of the upper unit.
The amount of cooling air required is indicated below. Also make sure that the tem-
perature of the cooling air does not exceed the maximum ambient temperature of
the converter.
*. Min clearance A and B for drives for
MI1 ~ MI3 can be 0 mm if the ambient
temperature is below 40 degrees.
F i g u r e 3 . 4 : I n s t a l l a t i o n s p a c e
A = clearance around the freq. converter (see also B)
B = distance from one frequency converter to another or distance to cabinet wall
C = free space above the frequency converter
D = free space underneath the frequency converter
NOTE! See the mounting dimensions on the back of the drive.
Leave free space for cooling above (100 mm), below (50 mm), and on the sides
(20 mm) of Vacon 10! For MI1 - MI3, side-to-side installation allowed only if the am-
bient temperature is below 40 °C.
Min clearance (mm)
Type A* B* C D
MI1 20 20 100 50
MI2 20 20 100 50
MI3 20 20 100 50
Table 3.1: Min. clearances around AC drive
Type Cooling air required (m³/h)
MI1 10
MI2 10
MI3 30
Table 3.2: Required cooling air
B
C
B
A
D
A

installation vacon • 13
24-hour support (0)201 212 575 • Email: [email protected]
3
3.1.3 Power losses
If the operator wants to raise the switching frequency of the drive for some reason
(typically e.g. in order to reduce the motor noise), this inevitably affects the power
losses and cooling requirements, for different motor shaft power, operator can se-
lect the switching frequency according to the graphs below.
MI1 - MI3 3P 380 V POWER LOSS

14 • vacon installation
Tel. [phone] • Fax [phone]
3
MI1 - MI3 3P 230 V POWER LOSS

installation vacon • 15
24-hour support (0)201 212 575 • Email: [email protected]
3

16 • vacon installation
Tel. [phone] • Fax [phone]
3
MI1 - MI3 1P 230 V POWER LOSS

installation vacon • 17
24-hour support (0)201 212 575 • Email: [email protected]
3