Vaporfi PRO II User manual

USER MANUAL
ENGLISH • ESPAÑOL

01
VAPORFI PRO II USER MANUAL
Thank you for purchasing the VaporFi Pro II vaporizer. In order to use your vaporizer
correctly, efficiently and safely, please follow the instructions in this manual.

THE VAPORFI PRO II STARTER KIT INCLUDES:
» (1) 650 mAh, 3.7 volt battery
» (1) Pro-L II tank with 1.5 OHM dual organic cotton coil (OCC)
» (1) USB charging cable
» (1) Wall charger
» (3) Additional 1.5 Ohm dual organic cotton coils (OCC) atomizers

03
GETTING STARTED
1. Turn the tank upside-down and unscrew the steel cap (see page 4).
2. Point and pour e-liquid into the sides of the tank. Fill to the edge of the center tube of the
tank. (DO NOT OVER-FILL OR POUR E-LIQUID INSIDE OF THE CENTER TUBE)
3. Screw the steel cap back onto the tank.
4. Screw the tank onto the battery. Do not over tighten parts, but ensure that all parts are
securely assembled.
5. To saturate the cotton coil with e-liquid, wait 1 to 2 minutes before vaping, then take a few
“dry puffs” without pressing the battery power button. This will avoid a “dry hit.”
6. Quickly press down and release on the battery’s power button 5 times within 2 seconds
to turn on your battery.
7. To use, press down and hold the power button while you take a puff. Release the button
when you have finished puffing and enjoy!

REFILLING E-LIQUID
When you have about 25% of e-liquid remaining or you experience a
slightly burnt taste, you will need to refill your tank with e-liquid.
1. Always remove the battery from the tank before refilling
with e-liquid. When unscrewing your tank from your battery,
always turn your device sideways, hold the steel cap located on
the tank and unscrew the battery counterclockwise.
2. Turn the tank upside-down and unscrew the steel cap.
3. Point and pour e-liquid into the sides of the tank. Fill to about 75%
capacity of the tank. (DO NOT OVER-FILL OR POUR E-LIQUID
INSIDE OF THE CENTER TUBE)
4. Screw the steel cap back onto the tank.
*VaporFi Pro-L II tanks contain O-rings that maintain an air-tight seal in order to
prevent leaking from the tank. Avoid over tightening of the tank’s steel base or
atomizer head as this could damage the O-rings and cause leaking. Therefore, when
screwing on your atomizer head or steel base, only tighten until you feel resistance.

05
CHANGING YOUR ATOMIZER HEAD
Once you experience a burnt taste, a decrease in flavor or vapor
production, it may be time to replace your atomizer head. It is
recommended to change your atomizer head once every 1-2 weeks
(depending on use).
To get the truest flavor from your e-liquid, we also suggest changing your
atomizer head when switching e-liquid flavors.
1. Before replacing your atomizer head, make sure your tank does not contain
any e-liquid.
2. To replace the atomizer head, turn your tank upside-down and unscrew and
remove the steel base by turning it counterclockwise.
3. While still holding onto the steel base, grip the top of the atomizer head and
unscrew it counterclockwise to remove the atomizer head from the steel base.

4. Once the old atomizer has been removed, screw in a new atomizer head by turning it clockwise
into the steel base until you feel resistance. Make sure not to over tighten the atomizer head as
this may damage the rubber O-rings and cause leakage.
5. Screw the steel base back onto your tank by turning it clockwise. Make sure not to over tighten.
6. Prime your atomizer by taking a few “dry puffs” without pressing the power button in order to
saturate the cotton within the coil, then let the device sit for 5 minutes to allow the e-liquid to
saturate the cotton ensuring a flavorful first pull and avoid a dry hit.

07
BATTERY OPERATION
TURNING BATTERY ON/OFF
» To turn the battery on, quickly press and release the power button 5 times within 2
seconds. The power button will flash 3 times to indicate that the device is ready for use.
» To turn the battery off, quickly press and release the power button 5 times within 2
seconds. The power button will flash 5 times to indicate that the device has turned off.
POWER SAVING SAFETY FEATURE
» If the battery’s power button is continuously pressed and held for 10 seconds, the
battery will flash 3 times and go into standby mode (hibernating).
» To continue use of the device after the battery hibernates, simply press the battery’s
power button and use as normal

CHARGING BATTERY
1. The LED indicator will flash 15 times to indicate that
the battery needs recharging.
2. Remove the tank and unscrew the steel cap from the
bottom of the battery.
3. Connect the USB charging cable into the port on the battery’s end.
4. Connect the other end of the USB charging cable to either the USB
port located on the wall charging adapter or to a fully powered USB
port, such as on a computer.
5. The indicator light on the battery will turn red
when charging and will glow green when complete.
6. Allow 2.5-3 hours for the battery to complete charging.
POWER
BUTTON
STEEL
CAP

09
WARNING
1. Always unplug the charger from the power supply before cleaning or refilling your device.
2. Do not use the battery with any charger that is not made specifically for this device.
3. Be careful to not let dust get into the tank or battery device.
4. Keep this device out of reach of children, and avoid improper operation.
5. Avoid making skin contact with the nicotine e-liquid.
6. If you experience an adverse reaction, reduce the strength of your nicotine, or switch to
0 nicotine. If problems persist, we recommend that you discontinue use of this product
and see a physician.

GUARANTEE
A 90-day warranty applies on manufacturing defects only. We cannot guarantee products
that have been damaged through improper use or have been mistreated. Visit our website
(www.VaporFi.com) for more details.
DISCLAIMER
VaporFi products are not smoking cessation proIducts and have not been tested as such.
The U.S. FDA has not approved these products for any use and they are not intended to
diagnose, cure, mitigate, treat or prevent any disorder, disease, or physical or mental
condition. Some VaporFi products contain nicotine, a chemical known to the State of
California to cause birth defects or other reproductive harm. Nicotine is addictive and
habit forming, and it is very toxic by inhalation, in contact with the skin, or if swallowed.
Ingestion of the non-vaporized concentrated ingredients in the cartridges can be
poisonous.

11
Physical effects of nicotine may include increased heart rate and accelerated blood
pressure. If the cartridge is swallowed, seek medical assistance immediately. VaporFi
products are intended for the use by adults of legal smoking age (18 or older in California),
and not by children, women who are pregnant or breast feeding, or persons with or at
risk of heart disease, high blood pressure, diabetes or taking medicine for depression or
asthma. VaporFi products may not be sold to minors. Identification of all persons under 26
will be required before purchase. KEEP OUT OF REACH OF CHILDREN.

MANUAL DE USUARIO

13
MANUAL DE USUARIO DE VAPORFI PRO II
Gracias por comprar el vaporizador VaporFi Pro II. Para poder usar su vaporizador en
forma correcta, eficiente y segura, siga las instrucciones de este manual.

EL KIT INICIAL DE VAPORFI PRO II INCLUYE:
» ( 1 ) Batería de 3,7 voltios, 650 mAh
» ( 1 ) Tanque doble bobina Pro-L II de 1.5 OHM con algodon organico (OCC)
» ( 1 ) Cable de carga USB
» ( 1 ) Cargador de pared
» ( 3 ) Atomizadores adicionales doble bobina de 1.5 OHM con algodon organico (OCC)

15
PARA EMPEZAR
1. Ponga el tanque hacia abajo y desenrosque la tapa de acero (página 14).
2. Apunte y vierta el e-líquido a los lados del tanque. Llene hasta el borde del tubo central
del tanque. (NO LO LLENE DEMASIADO NI VIERTA EL E-LÍQUIDO DENTRO DEL TUBO
CENTRAL).
3. Enrosque la tapa de acero de nuevo en el tanque.
4. Enrosque el tanque en la batería. No ajuste demasiado las piezas, pero sí asegúrese de
que todas las piezas estén bien ensambladas.
5. Deje reposar el dispositivo durante 1 a 2 minutos para que el e-líquido sature el algodón.
Esto garantiza un gran sabor y evita un “golpe seco”.
6. Presione y suelte rápidamente el botón de encendido de la batería 5 veces en 2 segundos
para encenderla.
7. Para usar el cigarrillo, mantenga presionado el botón de encendido mientras da una
pitada. Suelte el botón cuando haya terminado de pitar y ¡disfrute!

RECARGAR EL E-LÍQUIDO
Cuando le quede aproximadamente 25% del e-líquido en el tanque o
siente un sabor ligeramente quemado, tendrá que volver a llenar su
tanque de e-líquido.
1. Cuando el tanque esté vacío o cuando sienta un ligero sabor a
quemado, deberá recargar el tanque con el e-líquido.
2. Siempre retire la batería del tanque antes de recargarlo con el
e-líquido. Al desenroscar el tanque de su batería, siempre gire su
aparato de lado, sostenga la tapa de acero ubicada en el tanque y
afloje la batería en sentido antihorario.
3. Ponga el tanque hacia abajo y desenrosque la tapa de acero.
4. Apunte y vierta el e-líquido a los lados del tanque. Llene hasta aPro
IIximadamente el 75% de capacidad del tanque. (NO LO LLENE
DEMASIADO NI VIERTA EL E-LÍQUIDO DENTRO DEL TUBO CENTRAL).
*VaporFi Pro-L II tanques contienen O-Rings que mantienen un sello hermético para evitar fugas del
tanque. Evite el ajuste excesivo de la base de acero del tanque o la cabeza del atomizador, ya que
podría dañar los O-rings y causar fugas. Por lo tanto, cuando se ajuste la cabeza del atomizador o
base de su tanque, sólo aprete hasta que sienta resistencia.

17
CÓMO CAMBIAR EL CABEZAL DE SU ATOMIZADOR
Cuando sienta un sabor a quemado, una disminución en el sabor o la
Produducción de vapor, puede ser momento de reemplazar el cabezal de
su atomizador. Se recomienda cambiar el cabezal de su atomizador una
vez cada 1 - 2 semanas (dependiendo del uso).
A fin de obtener el sabor más auténtico del e-líquido, también sugerimos
cambiar el cabezal de su atomizador cuando cambie los sabores del
e-líquido.
1. Antes de reemplazar el cabezal de su atomizador, asegúrese de que su
tanque no contenga e-líquido.
2. Para reemplazar el cabezal del atomizador, ponga su tanque hacia abajo,
desenrosque y retire la base de acero girándola en sentido contrario a las
agujas del reloj.

3. Mientras aún sostiene la base de acero, sujete la parte superior del cabezal del atomizador y
desenrósquelo en sentido contrario a las agujas del reloj para retirarlo de la base de acero.
4. Una vez que haya retirado el atomizador usado, enrosque un nuevo cabezal de atomizador
girándolo en el sentido de las agujas del reloj en la base de acero hasta que sienta resistencia.
Asegúrese de no ajustar demasiado el cabezal del atomizador ya que esto puede dañar las
juntas de goma y ocasionar fugas.
5. Enrosque la base de acero de nuevo en su tanque girándola en el sentido de las agujas del reloj.
Asegúrese de no ajustarla demasiado.
6. Prepare su atomizador tomando algunas bocanadas de aire seco, sin pulsar el botón de
encendido con el fin de saturar el algodón dentro de la bobina, luego deje reposar el dispositivo
durante 5 minutos para que el e-líquido sature el algodón. Esto garantiza un gran sabor y evita
un golpe seco.