Vaporfi VOLT 2 User manual

QUICK START GUIDE
ENGLISH

WHAT’S INCLUDED
» [ 1 ] 4 ML Tank
» [ 1 ] SSOCC 0.5ohm Nichrome Atomizer
(Pre-Installed)
» [ 1 ] OCC 1.5ohm Atomizer
» [ 1 ] SSOCC Ni200 0.15 ohm Atomizer
» [6] O-Rings
» [ 1 ] Quick Start Guide

PRIMING & FILLING YOUR VOLT 2 TANK
1. Turn your tank upside down and unscrew atomizer base
from the tank.
2. Drop 3 drops of e-liquid into the exposed cotton holes
ensuring to wet each exposed cotton hole.
3. Screw the atomizer base back into the tank ensuring that
the atomizer base is snug but not too tight.
4. Unscrew the top fill cap by gripping the drip tip base
counter clockwise.
5. Use the top fill ports to fill your e-liquid to no more than
3/4 of the tank capacity.

CHANGING YOUR VOLT 2 ATOMIZER
Atomizers will endure anywhere between 7 – 14 days
depending on use and must be replaced when it has burned
out or no longer produces the proper volume of vapor.
1. Ensure that your tank is completely empty of e-liquid.
2. Remove the atomizer base from the tank and set the top
6. Once your e-liquid is filled, screw the top cap back
onto the tank and let your e-liquid soak the atomizer for 5
minutes.
7. Once Your liquid has properly saturated your atomizer,
you are ready to vape.

section of the tank aside.
3. Unscrew the atomizer using a counter clockwise motion
and discard the used atomizer.
4. Take a fresh atomizer and screw it into the tank base in
a clockwise motion. Ensure that your atomizer fits snuggly
without over tightening.
5. Follow the aforementioned steps to prime and fill your
tank then enjoy your favorite E-Liquid.
USING THE VOLT SERIES RBA IN YOUR VOLT 2 TANK
1. Follow the aforementioned steps to remove your atomizer.

NOTE: DO NOT REBUILD THIS DECK IF YOU ARE NOT AN
EXPERIENCED USER. REBUILDING AN RBA REQUIRES
KNOWLEDGE OF OHMS LAW AND A GREATER LEVEL OF
PATIENCE THEN A PRE-BUILT ATOMIZER.
BUILDING YOUR RBA DECK
2. Prime your RBA by dropping liquid onto the exposed
cotton while ensuring that you also drop generous amounts
of e-liquid onto the exposed coil as well.
3. Follow the previously mentioned steps to priming and
filling your tank and enjoy your favorite e-liquid.

1. To Rebuild your RBA, unscrew the top cap and side screw
to reveal the buildable deck.
2. Once this rebuildable deck is exposed, unscrew your used
replacement wire and discard it.
3. Take the replacement Volt Series RBA Replacement Wire
and mount into the screw holes and tighten the screws. (Be
sure to tighten the screws as much as possible in order to
ensure the best possible contact.)
4. Feed cotton into the center wrap of the wire and pull the
cotton through. Once the cotton is fed through the wire
hole, cut the cotton ensuring that it sits snuggly into the
deck.

NOTE: To ensure the most effective cotton feed, twist your
cotton between your finger tips and make a small point with
the leg of your cotton. When the cotton is able to enter the
wire, twist from both sides and feed it gently into the wire
opening. After the cotton has been guided through the wire
opening, cut both sides to fit into the RBA head.
5. Screw side screw back onto the RBA and screw the top
cap back onto RBA.
AIRFLOW CONTROL RING
To Adjust your airflow, twist the bottom airflow ring to your

TROUBLE SHOOTING YOUR VOLT 2 TANK
FLOODING:
If your tank begins to spit back, gurgle or produce less
preference. Cutting a 1/4 of the airflow is recommended for
users looking to achieve a restricted direct to lung draw.
To achieve a mouth to lung draw when using the 1.5 ohm
OCC coil, Close the airflow to 50%. It is not recommend to
completely close off the airflow as this will cause flooding
and spit back.

1. Blow into your drip tip while not firing your vape device.
2. If flooding persists, fire your vape device and blow into
tank. Be prepared for liquid to come out from the airflow
holes. Have a paper towel or napkin ready to clear residual
e-liquid.
3. If flooding continues to persist, blow into your drip tip
again while firing with your fingers wrapped in a paper
towel over all exposed airflow holes, lift and repeat.
vapor production it is likely that your tank has flooded. To
fix this issue follow the following steps:

You may then remove the atomizer base, remove your
atomizer and clean excess e-liquid from the atomizer base
reservoir using a paper towel.
VOLT 2 NOT FIRING
If your MOD reads atomizer short or no atomizer found,
ensure that your atomizer is screwed in tightly to the
atomizer base. If this issue persists, try another Atomizer
to ensure that your Atomizer is not defective. Repeat this
process and this issue will be resolved.

WARNING
Do not attempt to modify equipment; doing so can result
in permanent damage, overheating and/or explosion which
may lead to severe injuries or death.
For more information visit: vaporfi.com/how-it-works

DISCLAIMER
Vaporfi products are not smoking cessation products
and have not been tested as such. The U.S. FDA has not
approved these products for any use and they are not
intended to diagnose, cure, mitigate, treat or prevent any
disorder, disease, or physical or mental condition. Some
Vaporfi products contain a chemical known to the State
of California to cause cancer or birth defects or other
reproductive harm. Nicotine is addictive and habit forming,
and it is very toxic by inhalation, in contact with the skin, or
if swallowed.

DISCLAIMER

GUIA DE INICIO RAPIDO
ESPANOL

QUÉ ESTÁ INCLUIDO
» [ 1 ] 4 ML Tank
» [ 1 ] SSOCC 0.5ohm Nichrome Atomizador
(Pre-Instalado)
» [ 1 ] OCC 1.5ohm Atomizador
» [ 1 ] SSOCC Ni200 0.15 ohm Atomizador
» [6] O-Rings
» [ 1 ] Guia de Inicio Rapido

CÓMO LLENAR Y CEBAR SU TANQUE VOLT 2
1. Voltee el tanque y desenrosque el atomizador de la base
del mismo
2. Deje caeer 3 gotas de líquido en los agujeros de algodón
expuestos, asegurándose de mojar cada uno de dichos
agujeros
3. Vuelva a enroscar la base del atomizador en el tanque,
asegurándose de que la base del atomizador estés ajustada,
pero no demasiado apretada.
4. Desenrosque la tapa superior de llenado, agarrando la
base de la punta de goteo hacia la izquierda.

CAMBIAR SU ATOMIZADOR VOLT 2
Los atomizadores van a durar un perdíodo de entre 7-14
días dependiendo del uso y deben ser sustituidos cuando
5. Utilice el puerto superior de llenado para llenar su
e-liquido a no mas de 3/4 de la capacidad del tanque.
6. Una vez que el e-líquido ha sido llenado, atornille de
nuevo la tapa en el tanque y deje que el líquido remoje el
atomizador por 5 minutos.
7. Una vez que su líquido ha saturado correctamente su
atomizador, usted está listo para iniciar el vaping.

se han quemado o ya no producen el volumen apropiado de
vapor.
1. Asegúrese que el tanque esté completamente vacío de
líquido.
2. Retire la base del atomizador del tanque retirar y separe
la parte superior del mismo.
3. Desatornille atomizador con un movimiento hacia la
izquierda y deseche el atomizador usado.
4. Tome un atomizador fresco y atorníllelo en el tanque
en un movimiento hacia la derecha. Asegúrese de que el
atomizador se ajusta perfectamente sin apretar.