Vaporfi VOX 60 TC User manual

USER MANUAL
ENGLISH
VOX 60 TC

VAPORFI VOX® 60 TC USER MANUAL
Thank you for purchasing the Vaporfi VOX®60 TC. In order to
use your device correctly, efficiently and safely, please follow the
instructions in this manual.

THE VOX® 60 TC INCLUDES
» [ 1 ] 60W TC Mod
» [ 1 ] USB Charger
» [ 1 ] Manual

FEATURES
» Adjustable Output Power in 0.5W increments
» 2600 mAh dual internal Li-Po battery
» Accepts Atomizer Resistance from 0.1ohm (sub) - 3.5ohm
» Resistance (Standard coil): 0.1ohm - 3.5ohm
» Resistance (Ni 200/Ti coil) .05ohm – 1.0ohm
» Temperature Regulation Range (200F-600F), (100C-300C)
» Silver-plated brass Electrodes
» Output Voltage Range: 3.0V - 8V
» Output Power Range: 7W – 60W
» Maximum Output Current: 24.5 Amps
» 510 Threading with Spring Loaded Pin
» Output Short-Circuit Protection

» Reverse Battery Protection
» Auto Ohm Resistance Meter (Finds ideal voltage for RBA/RDA)
» Low Voltage Protection
» Device Lock Feature
» Low Resistance Protection
» Input High Voltage Warning
» Vented Battery Casing
» Zinc Alloy Construction
» Digital OLED Screen
» Pocket Sized: 79mm x 39mm x 24mm

TEMPERATURE CONTROL
Temperature control (TC) is the industry’s latest technology and
greatly benefits users. It is essentially the next step in consistent and
smooth vaping. If you’re unfamiliar with the technology, it ultimately
controls the temperature generated to your atomizer. As a result,
not only does temperature control prevent burnt coils, charring of
the wicking material, and dry hits, but it also increases your device’s
battery life. Adjusting the temperature in TC Mode (Ti/Ni) enables
customized temperature control of the coil.
The VOX®60W TC function works by determining the change in the
resistance of your coil as it heats up. Immediately after the device
notices a significant change in the resistance, the temperature
control function will reduce the power flow to the atomizer.
TURNING ON/OFF YOUR DEVICE
To turn your VOX®60W TC on or off simply click the power button 5
times within 2 seconds.

CHARGING YOUR DEVICE
Keeping a charged battery is just as important as the housing it rests
in. We recommend that you charge the VOX®60W TC built-in battery
to full capacity before using the device. By doing so, you will ensure
that the initial charge on the device is complete for a lengthy and
satisfying vaping experience at the beginning of use.
To charge your VOX®60W TC, plug the Micro-USB cord into the Micro-
USB port that is located on the bottom of the device. While the opposite
end is plugged into a USB port for power, an animation will appear on
the VOX®60W TC display screen, showing the battery is being charged.

ATTACHING A NEW ATOMIZER
The atomizer (also referred to as a coil) is the most important part of
any device. The coil is the part that turns the e- liquid within your tank
or RDA into vapor. Coils come in standard (Kanthal, Stainless Steel
or Clapton) & temperature control (Titanium or Nickel) resistances.
Atomizers also come in various resistance levels. The lower the
resistance the high the power, which means more vapor, flavor and a
stronger throat hit. Atomizers are like light bulbs – eventually will burn
out in time. Some will last a very long time (3 months) and some will go
quickly (1 to 2 weeks or less).
Once the battery has fully charged, you will see an animation appear on
the display screen showing a fully charged battery.

When attaching a standard (non-tc) atomizer in a tank or RDA of choice,
the VOX®60W TC is immediately ready for use.
However, when attaching a temperature control atomizer in a tank or
RDA of choice, the display screen will automatically prompt you with
“TEMP COIL SELECT” You’re given the option to choose what heating
wire that is currently in use. (Ti or Ni). ) If it does not read “TEMP COIL
SELECT” take off the tank and fire the device without a tank on it to
“reset” the device.
Once you’ve made your selection to indicate what heating wire you’ll
be using during the current session, another prompt will then ask if the
atomizer that is attached is a “New” or “Old” coil.

If you’ve previously attached the atomizer to the VOX®60W TC and
have the resistance already dialed in, then you may want to choose
“old”. If the atomizer is being freshly attached to the VOX®60W TC,
you may want to choose “new” to ensure that the correct resistance
has been established before use.
NOTE: Always ensure that when attaching an atomizer to your VOX
60W TC, that the coil is at room temperature. If you’ve recently
used the atomizer, give the coil time to cool down before following
the prompted steps. When choosing whether it is a new coil or old,
you are setting the resistance of your atomizer. If you get a “temp

LOCKING THE DEVICE
If you would like to lock/unlock the VOX®60W TC, press the power
button 3 times within 2 seconds. To lock/unlock your preferred settings
hold the power button and the “-“ button at the top of the device
simultaneously, this will lock in your preferred user setting on the VOX®
60W TC.
ADJUSTING WATTAGE
Wattage can be increased by 0.5 watt increments when pressing “+”
until the desired wattage is displayed. Press and hold the “+” button to
toggle through wattage quickly. Wattage can be decreased by 0.5 watt
protected” message, take off the tank and fire the device without
anything on it. Then make sure the coil is screwed in correctly and
tight. For the device to properly determine the resistance of the
atomizer and for the device to perform accurately, always follow the
above steps while the coil is at room temperature.

BYPASS/ MECH MODE
Bypass Mode is a direct output mode of voltage. This mode can only be
used with atomizer resistances under the range of 0.1-3.5 ohms.
To access bypass mode, increase wattage past 60 watts, the screen will
prompt “mecha”
increments when pressing “-” until the desired wattage is displayed.
Press and hold the “-” button to toggle through wattage quickly.

Your voltage level will be pointed to, and the device should fire at the
strength of the voltage vs the strength of your battery power. This mode
allows for maximum ratios between the device and atomizer.
NOTE: Vaporfi recommends only using Bypass mode with non-TC atomizers.
TEMP MODE
To access the temperature menu, you’ll need to first lock the device.
You can lock the device by pressing the power button 3 times within 2
seconds. Once you’ve entered the lock screen, resume by holding the
plus and minus buttons down until the temperature menu appears on the
display screen.

You may now adjust the temperature to your desired level. A higher
temperature provides a warmer vape experience; lower temperature
provides a lighter softer vape.
If you would like to disengage the temperature control feature, simply
choose the “OFF” setting. Once the desired level is reached, you may
now unlock the VOX®60W TC by clicking the power button 3 times
within 2 seconds.
MAINTENANCE & CARE
To properly maintain your device to ensure that it’s working to its full
potential, wipe the device down periodically with a micro fiber or dry
cloth. This will prevent any dust and particles from entering the device in
any way.
The 510 connection is highly important, since this is where your device
delivers power to the attached tank. Use a dry q-tip and periodically
clean the threading on the connection, as well as the spring-loaded

Being an electronic device, you’ll want to always avoid any contact with
water. If water or any liquid substance enters the device, it could cause
the battery to short and malfunction.
If you accidentally drop your device, vigorously inspect it and ensure that
it continues to work properly before being put back to use. If more than
visual damage appears, do not use the device, as the battery and internal
circuitry may be damaged and may potentially malfunction.
center pin. By doing so, you’re ensuring that your device and the
attached atomizer makes a solid connection each and every single time.

WARNING
Do not attempt to modify equipment; doing so can result in permanent
damage, overheating and/or explosion which may lead to severe injuries
or death.
For more information visit: vaporfi.com/how-it-works

GUARANTEE
All products come with a limited warranty. Please visit our website
(www.vaporfi.com) for more details.

DISCLAIMER
Vaporfi products are not smoking cessation products and have
not been tested as such. The U.S. FDA has not approved these
products for any use and they are not intended to diagnose, cure,
mitigate, treat or prevent any disorder, disease, or physical or
mental condition. Some Vaporfi products contain a chemical known
to the State of California to cause cancer or birth defects or other
reproductive harm. Nicotine is addictive and habit forming, and it is
very toxic by inhalation, in contact with the skin, or if swallowed.